I-Autonics TK Series Izilawuli Zezinga Lokushisa Ze-Autonics kanye Nokupholisa Kokukhiphayo kwe-PID

Siyabonga ngokukhetha umkhiqizo wethu we-Autonics

Funda futhi uqonde incwadi yeziqondiso kanye nemanuwali kahle ngaphambi kokusebenzisa umkhiqizo. Ukuze uphephe, funda futhi ulandele ukucatshangelwa kokuphepha okungezansi ngaphambi kokusebenzisa. Ukuze uphephe, funda futhi ulandele ukucatshangelwa okulotshwe encwadini yeziqondiso, amanye amamanuwali nama-Autonics webindawo. Gcina le manuwali yeziqondiso endaweni lapho ungathola khona kalula. Ukucaciswa, ubukhulu, njll kungashintsha ngaphandle kwesaziso sokuthuthukiswa komkhiqizo Amanye amamodeli angayekwa ngaphandle kwesaziso. Landela i-Autonics webindawo yemininingwane yakamuva.

Ulwazi Lomkhiqizo

I-TK Series Heating Simultaneous & Cooling Output PIDTemperature Controllers ingamadivayisi asetshenziselwa ukulawula izinga lokushisa ezinhlelweni ezihlukene. Ziza nezici ezingaphumeleli eziqinisekisa ukuphepha kwabasebenzisi futhi zinqande ukulimala kwemishini.

Izici Eziyinhloko

• Ukushisa ngesikhathi esisodwa kanye nokukhishwa kokupholisa
• I-algorithm yokulawula i-PID yokulawula izinga lokushisa okunembile
• Izinketho ezihlukene zokukhiphayo zokulawula ukuze zivumelane nezinhlelo zokusebenza ezithile
• Isekela imisebenzi eminingi ehlanganisa i-alamu, ukuphuma kokudlulisela, nokuxhumana kwe-RS485
• Ilinganiselwe ukusetshenziswa kwasendlini ezindaweni ezihlangabezana nemibandela ethile

Ukucatshangelwa Kokuphepha

Ngaphambi kokusebenzisa lo mkhiqizo, kubalulekile ukucabangela izinyathelo zokuphepha ezilandelayo:

1. Faka idivayisi engaphumeleli uma usebenzisa iyunithi enemishini engase ibangele ukulimala okubi noma ukulahlekelwa okukhulu kwezomnotho.
2. Gwema ukusebenzisa iyunithi ezindaweni lapho kukhona igesi evuthayo, eqhumayo, ebolayo, umswakama ophezulu, ukukhanya kwelanga okuqondile, ukushisa okukhazimulayo, ukudlidliza, umthelela noma usawoti omningi.
3. Faka iyunithi kuphaneli yedivayisi ozoyisebenzisa futhi ugweme ukuxhuma, ukulungisa noma ukuhlola iyunithi ngenkathi uxhumeke kumthombo wamandla.
4. Hlola ukuxhumana ngaphambi kokufakwa kwezintambo futhi ugweme ukuqaqa noma ukulungisa iyunithi.

Imiyalo yokusetshenziswa komkhiqizo

Landela le miyalo ukuze usebenzise i-TK Series Kanye Kanye
Izilawuli Zezinga Lokushisa Ze-PID Zokushisisa Nokupholisa:

1. Qinisekisa ukuthi ufake idivayisi engaphumeleli uma usebenzisa iyunithi enemishini engase ibangele ukulimala okubi noma ukulahlekelwa okukhulu kwezomnotho.
2. Khetha indawo efanelekile ngaphakathi endlini ehlangabezana nezimo zemvelo ezishiwo kumanuwali womkhiqizo.
3. Faka iyunithi kuphaneli yedivayisi ngaphambi kokuyisebenzisa.
4. Hlola uxhumo ngaphambi kokufakwa kwezintambo futhi usebenzise osayizi bekhebula abanconyiwe abachazwe kumanuwali womkhiqizo. Qinisa izikulufu zetheminali ekucacisweni kwetorque enconyiwe.
5. Sebenzisa isilawuli ngaphakathi kwezicaciso ezilinganiselwe ukugwema ukulimala noma ukungasebenzi kahle.
6. Sebenzisa indwangu eyomile ukuhlanza iyunithi futhi ugweme ukusebenzisa amanzi noma izincibilikisi eziphilayo ezingase zidale umlilo noma ukushaqeka kukagesi.
7. Gwema ukubeka umkhiqizo kuma-chips ensimbi, uthuli, nezinsalela zocingo ezingagelezela kuyunithi, zidale umonakalo noma umlilo.

Uku-oda Ulwazi

I-TK Series I-Simltaneous Heating & Cooling Output PID Temperature Controllers iza ngamamodeli ahlukene anezinketho ezihlukene zokufaka/okukhiphayo, umsebenzi, ukunikezwa kwamandla, nokukhishwa kokulawula. Ukuze uthole ulwazi olwengeziwe nokukhetha imodeli efanelekile, ungavakashela i-Autonics webindawo.

Ukucatshangelwa Kokuphepha

• Bheka konke 'Ukucatshangelwa Kokuphepha' ukuze usebenze ngendlela ephephile futhi efanele ukugwema izingozi.
• Uphawu lubonisa ukuqapha ngenxa yezimo ezikhethekile lapho izingozi zingase zenzeke khona.

Isexwayiso: Ukwehluleka ukulandela imiyalelo kungase kubangele ukulimala okubi kakhulu noma ukufa

1. Idivayisi ehluleka ukuphepha kufanele ifakwe uma kusetshenziswa iyunithi enemishini engase ibangele ukulimala okubi kakhulu noma ukulahlekelwa okukhulu komnotho. amadivaysi, njll.)
   • Ukwehluleka ukulandela lo myalelo kungase kubangele ukulimala komuntu siqu, ukulahlekelwa kwezomnotho noma umlilo.
2. Ungayisebenzisi iyunithi endaweni lapho igesi evuthayo/eqhumayo/ebolayo, umswakama ophezulu, ukukhanya kwelanga okuqondile, ukushisa okukhazimulayo, ukudlidliza, umthelela noma usawoti omningi.
   • Ukwehluleka ukulandela lo myalelo kungase kubangele ukuqhuma noma umlilo.
3. Faka kuphaneli yedivayisi ozoyisebenzisa.
   • Ukwehluleka ukulandela lo myalelo kungase kubangele ukushaqeka kukagesi.
4. Ungaxhumeki, ulungise, noma uhlole iyunithi ngenkathi uxhumeke kumthombo wamandla.
   • Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma ukushaqeka kukagesi.
5. Hlola 'Izixhumi' ngaphambi kokufaka izintambo.
   • Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo.
6. Ungaliqeqeshi noma uliguqule iyunithi.
   • Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma ukushaqeka kukagesi.

Isexwayiso: Ukwehluleka ukulandela imiyalelo kungase kubangele ukulimala noma ukulimala komkhiqizo.

1. Uma uxhuma okokufaka kwamandla kanye nokuphumayo kwe-relay, sebenzisa ikhebuli engu-AWG 20 (0.50 mm2) noma ngaphezulu, futhi uqinise isikulufu setheminali ngetorque eqinisayo engu-0.74 kuya ku-0.90 N m. Uma uxhuma ikhebuli yenzwa neyokuxhumana ngaphandle kwekhebula elizinikele, sebenzisa ikhebuli engu-AWG 28 ukuya ku-16 futhi uqinise isikulufu setheminali ngetorque eqinisayo engu-0.74 ukuya ku-0.90 N m.
   • Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma ukungasebenzi kahle ngenxa yokwehluleka ukuxhumana.
2. Sebenzisa iyunithi ngaphakathi kokucaciswa okulinganiselwe.
   • Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma umonakalo womkhiqizo
3. Sebenzisa indwangu eyomile ukuhlanza iyunithi, futhi ungasebenzisi amanzi noma i-organic solvent.
   • Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma ukushaqeka kukagesi.
4. Gcina umkhiqizo kude ne-chip yensimbi, uthuli, nezinsalela zocingo ezigelezela kuyunithi.
   • Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma umonakalo womkhiqizo.

Izixwayiso ngesikhathi sokusetshenziswa

• Landela imiyalelo kokuthi 'Izixwayiso ngesikhathi sokusebenzisa'. Uma kungenjalo, kungase kubangele izingozi ezingalindelekile.
• Hlola i-polarity yamatheminali ngaphambi kokufaka izintambo zenzwa yezinga lokushisa. Ngenzwa yezinga lokushisa ye-RTD, yifake ngentambo njengohlobo lwezintambo ezi-3, usebenzisa amakhebuli awugqinsi nobude obufanayo. Ngenzwa yethempelesha ye-thermocouple (TC), sebenzisa intambo yesinxephezelo emisiwe ukuze unwebe intambo.
• Gcina kude nevolumu ephezulutagolayini be-e noma izintambo zikagesi ukuvimbela umsindo ongenisayo. Uma kufakwa ulayini wamandla kanye nolayini wesignali wokufaka eduze, sebenzisa isihlungi somugqa noma i-varistor kulayini wamandla kanye nentambo evikelekile kulayini wesiginali yokufaka. Ungasebenzisi eduze kwesisetshenziswa esikhiqiza amandla kazibuthe anamandla noma umsindo wefrikhwensi ephezulu.
• Ungasebenzisi amandla weqile lapho uxhuma noma unqamula izixhumi zomkhiqizo.
• Faka iswishi yamandla noma i-circuit breaker endaweni efinyeleleka kalula ukuze unikeze noma unqamule amandla.
• Ungasebenzisi iyunithi ngezinye izinjongo (isb. voltmeter, ammeter), kodwa isilawuli lokushisa.
• Lapho ushintsha inzwa yokufaka, cisha ugesi kuqala ngaphambi kokushintsha. Ngemuva kokushintsha inzwa yokufaka, shintsha inani lepharamitha ehambisanayo.
• 24 VAC, 24-48 VDC Ukunikezwa kwamandla kufanele kufakwe i-insulated kanye nevolumu elinganiselwetagi-e/current noma i-Class 2, idivayisi yokunikeza amandla ka-SELV.
• Musa ukweqa ulayini wezokuxhumana nolayini wamandla. Sebenzisa izintambo zombili ezisontekile kulayini wokuxhumana bese uxhuma ubuhlalu be-ferrite ekugcineni ngakunye kolayini ukunciphisa umphumela womsindo wangaphandle.
• Yenza indawo edingekayo ezungeze iyunithi ngemisebe yokushisa. Ngokwesilinganiso sokushisa esinembile, fudumeza iyunithi ngaphezulu kwemizuzu engama-20 ngemuva kokuvula amandla.
• Qinisekisa ukuthi ukunikezwa kwamandla kagesi voltage ifinyelela ku-voltage elinganiselwetage phakathi kwamasekhondi angu-2 ngemva kokunikeza amandla.
• Ungafaki ucingo kumatheminali angasetshenziswanga.
• Le yunithi ingasetshenziswa ezindaweni ezilandelayo.
  • Ngaphakathi (kwisimo semvelo sikalwe 'Ngezici')
  • I-Altitude Max. 2,000 m
  • Idigri yokungcola 2
  • Isigaba sokufakwa II

Uku-oda Ulwazi

• Lokhu okokubhekisela kuphela, umkhiqizo wangempela awusekeli zonke izinhlanganisela.
• Ukuze ukhethe imodeli eshiwo, landela i-Autonics webindawo.

1. Usayizi
   • N: I-DIN W 48 × H 24 mm
   • SP: I-DIN W 48 × H 48 mm (uhlobo lwepulagi yamaphini angu-11)
   • S: I-DIN W 48 × H 48 mm
   • M: I-DIN W 72 × H 72 mm
   • W: I-DIN W 96 × H 48 mm
   • H: I-DIN W 48 × H 96 mm
   • L: I-DIN W 96 × H 96 mm
2. Inketho yokungena/yokukhiphayo
   

   Usayizi: N
   PN	OUT2	Umsebenzi
   1	Uhlobo olujwayelekile 01)	Okokufaka kwe-alamu 1 + CT
   	Ukushisa Nokuphola	I-alamu 2
   2	Uhlobo olujwayelekile	I-alamu 1 + I-alamu 2
   D	Uhlobo olujwayelekile	I-alamu 1 + Okokufaka kwedijithali 1/2
   	Ukushisa Nokuphola	Okokufaka kwedijithali 1/2
   R	Uhlobo olujwayelekile	I-alamu 1+Transmission okukhiphayo
   	Ukushisa Nokuphola	Ukudluliswa kokukhipha
   T	Uhlobo olujwayelekile	Okukhipha i-alamu 1 + RS485 ukuxhumana
   	Ukushisa Nokuphola	Ukuxhumana kwe-RS485

   Usayizi: SP
   PN	Umsebenzi
   1	I-alamu 1

   Usayizi: S, M, W, H, L
   PN	Umsebenzi
   1	I-alamu 1
   2	I-alamu 1 + I-alamu ephumayo 2
   R	I-alamu 1 + Ukukhipha okukhiphayo
   T	Ukuxhumana kwe-alamu 1 + RS485
   A	I-alamu 1 + I-alamu 2 + Ukukhipha okukhiphayo
   B	I-alamu 1 + Alarm 2 + RS485 ukuxhumana
   D	I-alamu 1 + I-alamu 2 + Okokufaka kwedijithali 1/2 02)

3. Ukunikezwa kwamandla kagesi
   • 2: 24 VAC 50/60 Hz, 24-48 VDC
   • 4: I-100-240 VAC 50/60 Hz
4. OUT1 Lawula okukhiphayo
   • R:  I-Relay
   • S: Ukushayela kwe-SSR
   • C: Okukhiphayo okukhethekayo kwedrayivu yamanje noma ye-SSR
5. OUT2 Lawula okukhiphayo
   • N: Uhlobo olujwayelekile
     • [Ayikho i-OUT2 (Ukushisisa noma Ukupholisa)]
   • R: Uhlobo lokushisisa nokupholisa
     • [Okukhiphayo kokudlulisa] 03)
   • C: Uhlobo lokushisisa nokupholisa
     • [Okukhiphayo kwamanje okukhethekayo noma kwedrayivu ye-SSR] 04)

Imodeli yokufaka ye-CI ot TK4N ingakhethwa kuphela kumodeli yohlobo oluvamile nge-alam Output 1. (ngaphandle kwe-TK4sP)

1. Ku-TK4S-D kuphela, ukuphela kwe-OUT2 okuphumayo kusetshenziswa njengetheminali yokufaka ye-D-2.
2. Uma imodi yokusebenza ingukulawula kokushisisa noma ukupholisa, i-OUT2 ingasetshenziswa njengokuphuma kwe-alamu 3 (ngaphandle kwe-TK4N).
3. Uma imodi yokusebenza ingukulawula kokushisisa noma ukupholisa, i-OUT2 ingasetshenziswa njengokuphuma kokudlulisela 2.

Imanuwali

• Ukuze usebenzise kahle umkhiqizo, bheka kumanuwali futhi uqiniseke ukuthi ulandela ukucatshangelwa kokuphepha kumamanuwali.
• Landa izincwadi ezivela ku-Autonics webindawo.

Isofthiwe

• Landa ukufakwa file kanye namamanuwali avela kuma-Autonics webindawo.

I-DAQMaster

• I-DAQMaster iwuhlelo oluphelele lokuphatha idivayisi. Iyatholakala ekusethweni kwepharamitha, ukuqapha.

Ithengiswa Ngokuhlukana

• 11 pin isokhethi: PG-11, PS-11 (N)
• I-Transformer yamanje (CT)
• Ikhava yokuvikela itheminali: Ikhava ye-RSA / RMA / RHA / RLA
• Isiguquli sokuxhumana: Uchungechunge lwe-SCM

Imininingwane

Uchungechunge		I-TK4N	I-TK4SP	I-TK4S	I-TK4M
Amandla hlinzeka	Uhlobo lwe-AC	100 – 240 VAC 50/60 Hz ±10%
	Uhlobo lwe-AC/DC	–	24 VAC 50/60 Hz ±10%, 24-48 VDC ±10%
Amandla ukusetshenziswa	Uhlobo lwe-AC	≤ 6 VA	≤ 8 VA
	Uhlobo lwe-AC/DC	–	AC: ≤ 8 VA, DC ≤ 5W
Iyunithi isisindo (pakishiwe)		≈ 70 g (≈ 140 g)	≈ 85 g (≈ 130 g)	≈ 105 g (≈ 150 g)	≈ 140 g (≈ 210 g)

 

Uchungechunge		I-TK4W	I-TK4H	I-TK4L
Amandla hlinzeka	Uhlobo lwe-AC	100 – 240 VAC 50/60 Hz ±10%
	Uhlobo lwe-AC/DC	24 VAC 50/60 Hz ±10%, 24-48 VDC ±10%
Amandla ukusetshenziswa	Uhlobo lwe-AC	≤ 8 VA
	Uhlobo lwe-AC/DC	AC: ≤ 8 VA, DC ≤ 5W
Iyunithi isisindo (pakishiwe)		≈ 141 g (≈ 211 g)	≈ 141 g (≈ 211 g)	≈ 198 g (≈ 294 g)

 

Sampling isikhathi		50 ms
Ukucaciswa kokokufaka		Bheka 'Uhlobo Lokufaka Nokusebenzisa Ububanzi'
Inketho okokufaka	Okokufaka kwe-CT	0.0-50.0 A (ibanga lokulinganisa eliyinhloko lamanje) Isilinganiso se-CT: 1/1,000 Ukunemba kokulinganisa: ±5% FS ±1dijithi
	Okokufaka kwedijithali	Othintana naye – VULIWE: ≤ 2 kΩ, VALIWE: ≥ 90 kΩ Abangaxhumani nabo - residual voltage ≤ 1.0 V, ukuvuza kwamanje ≤ 0.1 mA Ukuphuma kwamanje: ≈ 0.5 mA okokufaka ngakunye
Lawula okukhiphayo	I-Relay	250 VAC 3 A, 30 VDC 3 a1a
	I-SSR	11 VDC±2 V, ≤ 20 mA
	Okwamanje	I-DC 4-20 mA noma i-DC 0-20 mA (ipharamitha), Ukumelana nomthwalo: ≤ 500 Ω
I-alamu okukhiphayo	I-Relay	I-AL1, AL2: 250 VAC 3 a1a I-TK4N AL2: 250 VAC 0.5 A 1a (≤ 125 VA)
Inketho okukhiphayo	Ukudluliswa	I-DC 4 – 20 mA (Ukumelana nomthwalo: ≤ 500 Ω, Ukunemba kokuphumayo: ±0.3% FS)
	RS485 com.	I-Modbus RTU
Bonisa uhlobo		7 ingxenye (obomvu, oluhlaza, ophuzi), uhlobo lwe-LED
Lawula uhlobo	Ukushisisa, Ukupholisa	VULIWE/VAMILE, P, PI, PD, PID Control
	Ukushisisa & Ukupholisa
I-Hysteresis		I-Thermocouple, i-RTD: 1 kuya ku-100 (0.1 kuya ku-100.0) ℃/℉ I-Analog: idijithi engu-1 kuye kweyi-100
Ngokulinganayo ibhande (P)		0.1 kuye ku-999.9 ℃/℉ (0.1 kuya ku-999.9%)
Okuphelele isikhathi (I)		0 kuya ku-9,999 isekhondi
Okuphuma kokunye isikhathi (D)		0 kuya ku-9,999 isekhondi
Lawula umjikelezo (T)		Ukukhishwa kwe-relay, ukuphuma kwedrayivu ye-SSR: 0.1 kuya ku-120.0 sec Okuphumayo kwedrayivu ekhethekayo yamanje noma ye-SSR: 1.0 kuya ku-120.0 sec
Imanuwali setha kabusha		0.0 ukuya ku-100.0%
I-Relay ukuphila umjikelezo	Omakhenikha	OUT1/2: ≥ 5,000,000 imisebenzi AL1/2: ≥ 20,000,000 imisebenzi (TK4H/W/L: ≥ 5,000,000 imisebenzi)
	Ezogesi	≥ 100,000 imisebenzi
I-Dielectric amandla		Phakathi kwetheminali yomthombo wamandla kanye netheminali yokokufaka: 2,000 VAC 50/60 Hz iminithi elingu-1
Ukudlidliza		0.75 mm amplitude imvamisa ye-5 kuye ku-55 Hz (iminithi elingu-1) endaweni ngayinye engu-X, Y, Z amahora ama-2
I-Insulation ukumelana		≥ 100 MΩ (500 VDC megger)
Umsindo ukungatheleleki		±2 kV umsindo oyisikwele oyisikwele ngesifanisi somsindo (ububanzi be-pulse: 1 ㎲) Isigaba se-R, isigaba se-S
Inkumbulo ukugcinwa		≈ iminyaka eyi-10 (uhlobo lwenkumbulo ye-semiconductor engaguquki)
I-ambient izinga lokushisa		-10 kuya ku-50 ℃, isitoreji: -20 kuya ku-60 ℃ (akukho ukuqandisa noma ukujiya)
I-ambient umswakama		35 kuya ku-85%RH, isitoreji: 35 kuya ku-85%RH (akukho ukuqandisa noma ukujiya)
Ukuvikelwa isakhiwo		IP65 (Iphaneli yangaphambili, amazinga e-IEC) • I-TK4SP: IP50 (Iphaneli yangaphambili, amazinga e-IEC)
I-Insulation uhlobo		Ukufakwa kabili noma ukufakwa okuqinisiwe (maka: , amandla e-dielectric phakathi kwengxenye yokukala nengxenye yamandla: 2 kV)
Isesekeli		Ubakaki, ikhava yokuvikelwa kwetheminali (TK4N)
Ukugunyazwa

Isixhumanisi Esibonakalayo

RS485

Comm. umthetho olandelwayo	I-Modbus RTU
Ukuxhumana uhlobo	RS485
Isicelo ejwayelekile	Ukuhambisana ne-EIA RS485
Ubuningi uxhumano	Amayunithi angama-31 (ikheli: 01 kuya ku-99)
Kuyavumelaniswa indlela	Asynchronous
Comm. Indlela	I-double-wire half duplex
Comm. ngempumelelo ububanzi	≤ 800 m
Comm. isivinini	2,400 / 4,800 / 9,600 (okuzenzakalelayo) / 19,200 / 38,400 bps (ipharamitha)
Impendulo isikhathi	5 kuya ku-99 ms (okuzenzakalelayo: 20 ms)
Qala kancane	Ibhithi elingu-1 (elilungisiwe)
Idatha kancane	Ibhithi elingu-8 (elilungisiwe)
Ukulingana kancane	Akukho (okuzenzakalelayo), Okungajwayelekile, Ngisho
Ima kancane	1 bit, 2 bit (okuzenzakalelayo)
EEPROM ukuphila umjikelezo	≈ 1,000,000 imisebenzi (Sula / Bhala)

Uhlobo Lokufaka kanye Nokusetshenziswa Kwebanga

Uhla lwamasethingi lwamanye amapharamitha lunomkhawulo uma usebenzisa isibonisi sephoyinti ledesimali.

Okokufaka uhlobo		Idesimali iphuzu	Bonisa	Ukusebenzisa ububanzi (℃)			Ukusebenzisa ububanzi (℉)
Thermo -umbhangqwana	I-K (CA)	1	KCaH	-200	ku	1,350	-328	ku	2,463
		0.1	I-KCaL	-199.9	ku	999.9	-199.9	ku	999.9
	I-J (IC)	1	I-JIcH	-200	ku	800	-328	ku	1,472
		0.1	I-JIcL	-199.9	ku	800.0	-199.9	ku	999.9
	E (CR)	1	I-ECrH	-200	ku	800	-328	ku	1,472
		0.1	I-ECrL	-199.9	ku	800.0	-199.9	ku	999.9
	I-T (CC)	1	I-TccH	-200	ku	400	-328	ku	752
		0.1	I-TCcL	-199.9	ku	400.0	-199.9	ku	752.0
	B (PR)	1	B PR	0	ku	1,800	32	ku	3,272
	I-R (PR)	1	R PR	0	ku	1,750	32	ku	3,182
	I-S (PR)	1	S PR	0	ku	1,750	32	ku	3,182
	N (NN)	1	N NN	-200	ku	1,300	-328	ku	2,372
	C (TT) 01)	1	C TT	0	ku	2,300	32	ku	4,172
	G (TT) 02)	1	G TT	0	ku	2,300	32	ku	4,172
	I-L (IC)	1	I-LIcH	-200	ku	900	-328	ku	1,652
		0.1	I-LIcL	-199.9	ku	900.0	-199.9	ku	999.9
	U (CC)	1	UCCH	-200	ku	400	-328	ku	752
		0.1	UCCL	-199.9	ku	400.0	-199.9	ku	752.0
	I-Platinel II	1	I-PLII	0	ku	1,390	32	ku	2,534
I-RTD	ku50 Ω	0.1	CU5	-199.9	ku	200.0	-199.9	ku	392.0
	ku100 Ω	0.1	CU10	-199.9	ku	200.0	-199.9	ku	392.0
	I-JPt100 Ω	1	I-JPtH	-200	ku	650	-328	ku	1,202
		0.1	I-JPtL	-199.9	ku	650.0	-199.9	ku	999.9
	I-DPt50 Ω	0.1	I-DPT5	-199.9	ku	600.0	-199.9	ku	999.9
	I-DPt100 Ω	1	I-DPtH	-200	ku	650	-328	ku	1,202
		0.1	I-DPtL	-199.9	ku	650.0	-199.9	ku	999.9
	I-Nickel 120 Ω	1	NI12	-80	ku	200	-112	ku	392
I-Analog	0 ukuze 10 V	–	I-AV1			0 kuye	10 V
	0 ukuze 5 V	–	I-AV2			0 kuye	5 V
	1 ukuze 5 V	–	I-AV3			1 kuye	5 V
	0 kuya ku-100 mV	–	I-AMV1			0 kuye	100 mV
	0 kuya ku-20 mA	–	AMA1			0 kuye	20 mA
	4 kuya ku-20 mA	–	AMA2			4 kuye	20 mA

1. C (TT): Ngokufanayo nenzwa yohlobo lwe-W5 (TT) ekhona
2. G (TT): Ngokufanayo nenzwa yohlobo lwe-W (TT) ekhona

• Ukumelana komugqa okuvunyelwe ngomugqa ngamunye: ≤ 5 Ω

Bonisa ukunemba

Okokufaka uhlobo	Ukusebenzisa izinga lokushisa	Bonisa ukunemba
Thermo - I-RTD yombhangqwana	Ngezinga lokushisa lekamelo (23℃ ±5 ℃)	(PV ±0.3% noma ±1 ℃ eyodwa ephakeme) ±1-idijithi • I-Thermocouple K, J, T, N, E ngezansi -100 ℃ kanye no-L, U, PII, RTD Cu50 Ω, Dpt50 Ω: (PV ±0.3% noma ±2 ℃ eyodwa ephakeme) ±1 idijithi • I-Thermocouple C, G no-R, S ngaphansi kuka-200 ℃: (PV ±0.3% noma ±3 ℃ eyodwa ephakeme) ±1-idijithi • I-Thermocouple B ngaphansi kuka-400 ℃: Awekho amazinga okunemba
	Ngaphandle kwebanga lokushisa kwegumbi	(PV ±0.5% noma ±2 ℃ eyodwa ephakeme) ±1-idijithi • RTD Cu50 Ω, Dpt50 Ω: (PV ±0.5% noma ±3 ℃ eyodwa ephakeme) ±1 idijithi • I-Thermocouple R, S, B, C, G: (PV ±0.5% noma ±5 ℃ eyodwa ephakeme) ±1-idijithi • Ezinye izinzwa: ≤ ±5 ℃ (≤-100 ℃)
I-Analog	Ngezinga lokushisa lekamelo (23℃ ±5 ℃)	±0.3% FS ±1-idijithi
	Ngaphandle kwebanga lokushisa kwegumbi	±0.5% FS ±1-idijithi

• Esimeni se-TK4SP Series, ±1 ℃ izokwengezwa kuzinga ledigri.

Izincazelo zeyunithi

1. Ingxenye yesibonisi se-PV (Bomvu)
   • Imodi yokuqalisa: Ibonisa i-PV (inani lamanje).
   • Imodi yokusetha: Ibonisa igama lepharamitha.
2. Ingxenye yesibonisi ye-SV (Luhlaza)
   • Imodi yokuqalisa: Ibonisa i-SV (Inani lokusetha).
   • Imodi yokusetha: Ibonisa inani lokusetha ipharamitha.
3. Ukhiye wokufaka
   

   Bonisa	Igama
   [A/M]	Lawula ukhiye wokushintsha
   [IMODE]	Ukhiye wemodi
   [◀], [▼], [▲]	Ukusetha ukhiye wokulawula inani

4. Inkomba
   

   Bonisa	Igama	Incazelo
   ℃, %, ℉	Iyunithi	Ibonisa iyunithi ekhethiwe (ipharamitha)
   AT	Ukushuna okuzenzakalelayo	Iyabaneka ngesikhathi sokushuna okuzenzakalelayo njalo ngesekhondi elingu-1
   OUT1/2	Lawula okukhiphayo	IVULA uma okukhiphayo kokulawula KUVULIWE Okukhiphayo kwe-SSR (ukulawula umjikelezo/isigaba) I-MV ngaphezu kuka-5% IVULIWE Okukhiphayo kwamanje Ukulawula mathupha: 0% ISELULE, phezu VULIWE Ukulawula okuzenzakalelayo: ngaphansi kuka-2% ISELWE, ngaphezu kuka-3% VULIWE
   AL1/2	Okukhipha i-alamu	IVULA uma okukhiphayo kwe-alamu KUVULIWE
   INDODA	Ukulawula mathupha	IVULA ngesikhathi sokulawula mathupha
   SV1/2/3	I-Multi SV	Inkomba ye-SV IVULIWE okwamanje eboniswayo. (Uma usebenzisa umsebenzi we-SV eminingi)

   

5. Imbobo ye-PC loader: Okokuxhuma isiguquli sokuxhumana (uchungechunge lwe-SCM).

• Ukuze uthole imininingwane mayelana nemodeli endala, bheka imanuwali yomsebenzisi. Landa izincwadi ezivela ku-Autonics webindawo.

Ubukhulu

• Iyunithi: mm, Ukuze uthole imidwebo enemininingwane, landela i-Autonics webindawo.
• Ngezansi kusekelwe ku-TK4S Series.

Ukuphuma kwepaneli

Ubakaki

I-TK4N /TK4S/SP/Olunye uchungechunge

Ikhava yokuvikela itheminali

I-TK4N

Indlela Yokufaka

I-TK4N

• Ngemva kokukhweza umkhiqizo kuphaneli ngobakaki, qinisa amabhawodi usebenzisa isikrudrayiva.

Okunye uchungechunge

• Faka iyunithi kuphaneli, qinisa ubakaki ngokuphusha nge-screwdriver ye-flathead.

Amaphutha

Bonisa	Okokufaka	Incazelo	Okukhiphayo	Ukuxazulula inkinga
	Inzwa yezinga lokushisa	Ikhanya ngesikhawu samasekhondi angu-0.5 lapho inzwa yokufaka inqanyulwa noma inzwa ingaxhumekile.	'Iphutha lenzwa, MV' inani lokusetha ipharamitha	Hlola isimo sesizweli sokufaka.
VULA
	I-Analog	Ibaneka ngesikhawu sesekhondi elingu-0.5 uma okokufaka kungaphezu kwe-FS ±10%.	'Iphutha lenzwa, Ipharamitha ye-MV ukusetha inani	Hlola isimo sokufakwayo kwe-analogi.
	Inzwa yezinga lokushisa	Ibaneka ngezikhawu zamasekhondi angu-0.5 uma inani lokokufaka lingaphezu kobubanzi bokufaka.	Ukushisisa: 0%, Ukupholisa: 100%
HHHH
	I-Analog	Ibaneka ngezikhawu zamasekhondi angu-0.5 uma i inani lokufakwayo lingaphezu kuka-5 kuya ku-10% wokuphakama umkhawulo noma inani eliphansi lomkhawulo.	Okukhipha okujwayelekile	Lapho okokufaka kungaphakathi kwebanga lokufaka elinganisiwe, lesi sibonisi siyanyamalala.
	Inzwa yezinga lokushisa	Ikhanya ngo-0.5 sec. izikhawu uma inani lokokufaka lingaphansi kobubanzi bokufaka.	Ukushisisa: 100%, Ukupholisa: 0%
I-LLLL
	I-Analog	Ibaneka ngezikhawu zamasekhondi angu-0.5 uma i inani lokokufaka lingaphezu kuka-5 kuya ku-10% of low umkhawulo noma inani eliphezulu lomkhawulo.	Okukhipha okujwayelekile
IPHUTHA	Inzwa yezinga lokushisa	Ibaneka ngezikhawu ezingamasekhondi angu-0.5 uma kunephutha lokusetha futhi ibuyela kuphutha-ngaphambi kwesikrini.	–	Hlola indlela yokusetha.
	I-Analog

Ukuxhumana

• Amatheminali anomthunzi ayimodeli evamile.
• Okokufaka kwedijithali akuvalwa ngogesi kusuka kumasekhethi angaphakathi, ngakho-ke kufanele kugqunywe lapho kuxhunywa amanye amasekhethi.

I-TK4N

I-TK4S

I-TK4SP

I-TK4M

TK4H / W / L

Ukucaciswa kwetheminali ye-Crimp

• Iyunithi: mm, Sebenzisa itheminali ye-crimp yomumo wokulandela.

Isibonisi Sasekuqaleni Lapho Amandla Evuliwe

• Uma amandla enikezwa, ngemva kokuthi isibonisi sizokhanyisa isekhondi elingu-1, igama lemodeli liboniswa ngokulandelana. Ngemuva kokuthi uhlobo lwenzwa yokufaka luzokhanya kabili, ngena kumodi ye-RUN.

	1. Konke isibonisi	2. Imodeli	3. Okokufaka ukucaciswa	4. Imodi yokuqalisa
PV isibonisi ingxenye	*** 8	I-TK4	I-TK4	VULA
Ingxenye yokubonisa ye-SV	*** 8	I-14RN	KCaH	0

Ukusetha Imodi

Ukusetha Ipharamitha

• Amanye amapharamitha ayenziwa asebenze/angasebenzi kuye ngemodeli noma ukulungiselelwa kwamanye amapharamitha.
• Isici esithi 'Imaski Yepharamitha', esifihla amapharamitha angadingekile noma angasebenzi, kanye nesici 'seqembu lepharamitha yomsebenzisi', esisetha ngokushesha futhi kalula amapharamitha athile asetshenziswa njalo, singasethwa ku-DAQMaster.
• Bheka kumanuwali yomsebenzisi ukuze uthole imininingwane.

Ipharamitha 1 iqembu

Ipharamitha	Bonisa	Okuzenzakalelayo
Lawula okukhiphayo GIJIMA / YIMA	RS	GIJIMA
Ukukhetha okuningi kwe-SV	I-SV-N	I-SV-0
I-heater yamanje ukuqapha	I-CT-A	)0
Okukhipha i-alamu1 umkhawulo ophansi	AL!L	1550
Okukhipha i-alamu1 umkhawulo ophezulu	AL!H	1550
Okukhipha i-alamu2 umkhawulo ophansi	AL@L	1550
Okukhipha i-alamu2 umkhawulo ophezulu	AL@H	1550
Okukhipha i-alamu3 umkhawulo ophansi	AL#L	1550
Okukhipha i-alamu3 umkhawulo ophezulu	AL#H	1550
I-Multi SV 0	I-SV-0	0000
I-Multi SV 1	I-SV-1	0000
I-Multi SV 2	I-SV-2	0000
I-Multi SV 3	I-SV-3	0000

Ipharamitha 2 iqembu

Ipharamitha	Bonisa	Okuzenzakalelayo
Ukushuna okuzenzakalelayo RUN/STOP	AT	VALIWE
Ukushisa ngokulingana ibhande	HP	01)0
Ibhendi elinganiselayo yokupholisa	I-CP	01)0
Isikhathi esibalulekile sokushisa	H-1	0000
Ukupholisa isikhathi esibalulekile	C-1	0000
Isikhathi sokuphuma kokushisisa	I-HD	0000
Ukupholisa isikhathi sokuphuma kokunye	I-CD	0000
Ibhendi yokudlulana efile	DB	0000
Ukusetha kabusha mathupha	PHUMULA	05)0
Ukushisa kwe-hysteresis	HYS	002
Ukushisisa OFF offset	i-hoST	000
Ukupholisa i-hysteresis	I-chYS	002
Ukupholisa OFF offset	I-COST	000
MV umkhawulo ophansi	I-L-MV	`0)0
Inani eliphakeme kakhulu lama-MV	H-MV	10)0
RAMP izinga lokushintsha	I-RAMU	000
RAMP izinga lokushintsha eliphansi	RAMD	000
RAMP iyunithi yesikhathi	I-rUNT	MIN

Ipharamitha 3 iqembu

Ipharamitha	Bonisa	Okuzenzakalelayo
Ukucaciswa kokokufaka	I-IN-T	KCaH
Iyunithi yezinga lokushisa	I-UNIT	?C
Umkhawulo ophansi we-analogi	I-L-RG	0)00
Umkhawulo ophezulu we-analogi	H-RG	1)00
Ukukala iphoyinti ledesimali	I-DOT	)0
Isikali somkhawulo ophansi	L-SC	00)0
Isilinganiso esiphezulu somkhawulo	H-SC	10)0
Iyunithi yokubonisa	I-dUNT	?/O
Ukulungisa okokufaka	IN-B	0000
Isihlungi sedijithali sokufaka	MAVF	00)1
SV umkhawulo ophansi	I-L-SV	-200
Inani eliphakeme kakhulu lama-SV	H-SV	1350
Lawula imodi yokuphumayo	O-FT	UKUSHISA (Uhlobo olujwayelekile)
		HC (Ukushisa nokupholisa uhlobo)
Uhlobo lokulawula	C-MD	I-PID (Ejwayelekile           uhlobo)
		pP (Ukushisisa nokupholisa- uhlobo)
Imodi yokushuna ngokuzenzakalela	E-T	I-TUN1
OUT1 ukulawula okukhiphayo ukukhetha	OUT1	I-CURR
OUT1 okukhiphayo kwedrayivu ye-SSR uhlobo	O!SR	STND
OUT1 okukhiphayo kwamanje ububanzi	O!MA	4-20
OUT2 lawula ukukhetha okukhiphayo	OUT2	I-CURR
OUT2 ibanga lokuphumayo lamanje	O@MA	4-20
Umjikelezo wokulawula ukushisa	HT	02)0 (Relay) 00@0 (SSR)
Umjikelezo wokulawula ukupholisa	CT

Ipharamitha 4 iqembu

Ipharamitha	Bonisa	Okuzenzakalelayo
Okukhipha i-alamu1 Ukusebenza imodi	AL-1	I-DVCC
Okukhipha i-alamu1 Inketho	AL!T	I-AL-A
Okukhipha i-alamu1 I-Hysteresis	A!HY	001
Oxhumana naye we-alamu ophumayo uhlobo	A!N	CHA
Okukhipha i-alamu1 KUVULIWE ukubambezeleka isikhathi	A!VULIWE	0000
Okukhipha i-alamu1 KUVALIWE ukubambezeleka isikhathi	A!KWE	0000
Okukhipha i-alamu2 Imodi yokusebenza	AL-2	]]DV
Okukhipha i-alamu2 Inketho	AL@T	I-AL-A
Okukhipha i-alamu2 I-Hysteresis	A@HY	001
Uhlobo lokuxhumana lwe-alamu2	A@N	CHA
Okukhipha i-alamu2 KUVULIWE isikhathi sokulibaziseka	A@ON	0000
Isikhathi sokulibaziseka se-alamu2 VALIWE	A@OF	0000
Okukhipha i-alamu3 Imodi yokusebenza	AL-3	VALIWE
Okukhipha i-alamu3 Inketho	AL#T	I-AL-A
Okukhipha i-alamu3 I-Hysteresis	A#HY	001
Uhlobo lokuxhumana lwe-alamu3	A#N	CHA
Okukhipha i-alamu3 KUVULIWE isikhathi sokulibaziseka	A#ON	0000
Isikhathi sokulibaziseka se-alamu3 VALIWE	A#OF	0000
Isikhathi se-LBA	LBaT	0000
Iqembu le-LBA	LBaB	002 (003)
I-Analog Transmission okukhipha1 Imodi	I-AoM1	PV
Ukukhipha okukhipha1 umkhawulo ophansi	FsL1	-200
Ukukhipha okukhipha1 umkhawulo ophezulu	FsH1	1350
Imodi ye-Analog Transmission2	I-AoM2	PV
Umkhawulo wokudlulisa ongu-2 umkhawulo ophansi	FsL2	-200
Ukukhishwa kokudlulisela2 umkhawulo ophezulu	FsH2	1350
Ikheli lokuxhumana	ADRS	01
Isivinini sokuxhumana	I-BPS	96
Comm. ukulingana kancane	PRTY	AKUKHO
Comm. yima kancane	I-STP	2
Isikhathi sokuphendula	I-RSWT	20
Comm. bhala	I-COMW	I-EnA

Ipharamitha 5 iqembu

OXHUMANA NABO

• 18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002
• www.kuzithin.com
• +82-2-2048-1577
• sales@autonics.com

Amadokhumenti / Izinsiza

I-Autonics TK Series Izilawuli Zezinga Lokushisa Ze-Autonics kanye Nokupholisa Kokukhiphayo kwe-PID [pdf] Incwadi Yeziqondiso I-TK Series, i-TK Series, i-TK Series, Izilawuli Zezinga lokushisa Eziphuma Ngasikhathi sinye kanye Nezokupholisa ze-PID, Izilawuli Zezinga lokushisa ze-PID, Izilawuli Zezinga Lokushisa Zokushisisa kanye Nokupholisa, Izilawuli Zezinga lokushisa ze-PID

Izithenjwa

• Imaniwali yosebenzisayo