I-Autonics TCD210240AC Izilawuli Zezinga lokushisa ze-PID ngesikhathi esisodwa kanye Nokupholisa

Ulwazi Lomkhiqizo

Izilawuli ze-TK Series Zokushisisa kanye Nokupholisa Kokukhipha I-PID zingamadivayisi asetshenziselwa ukulawula izinga lokushisa ezinhlelweni ezihlukahlukene ezihlanganisa imishini, okokusebenza kwezokwelapha, okokusebenza zokuphepha, nokunye. Izilawuli zinamadivayisi angaphumeleli afakiwe ukuze kuvinjelwe ukulimala okubi noma ukulahlekelwa kwezomnotho. Zenzelwe ukusebenza endaweni yasendlini enobude obungafika ku-2,000m kanye nedigri yokungcola engu-2. Izilawuli zinezinketho ezihlukahlukene zoku-oda okokufaka/okuphumayo, umsebenzi, kanye nokunikezwa kwamandla. Banokukhiphayo kokulawula okungaba idrayivu edluliselwe, idrayivu ye-SSR, noma idrayivu ekhethekayo yamanje noma ye-SSR. Umkhiqizo akufanele usetshenziswe ezindaweni lapho igesi evuthayo/eqhumayo/ebolayo, umswakama ophezulu, ukukhanya kwelanga okuqondile, ukushisa okukhazimulayo, ukudlidliza, umthelela, noma usawoti.

Imiyalo yokusetshenziswa komkhiqizo

1. Faka isilawuli kuphaneli yedivayisi endaweni yasendlini enobude obungafika ku-2,000m kanye nedigri yokungcola engu-2.
2. Qinisekisa ukuthi amadivayisi angaphumeleli afakiwe uma usebenzisa isilawuli esinemishini engase ibangele ukulimala okubi noma ukulahlekelwa okukhulu komnotho.
3. Sebenzisa ikhebuli ye-AWG 20 (0.50 mm2) noma ngaphezulu lapho uxhuma okokufaka kwamandla kanye nokuphumayo kwe-relay. Sebenzisa ikhebuli engu-AWG 28 ukuya ku-16 lapho uxhuma okokufaka kwenzwa nekhebuli yokuxhumana ngaphandle kwekhebula elizinikele.
4. Qinisa izikulufu zetheminali ngetorque engu-0.74 ukuya ku-0.90 N m lapho uxhuma izintambo.
5. Hlola ukuxhumana ngaphambi kokufakwa kwezintambo ukuze uvimbele umlilo.
6. Sebenzisa isilawuli ngaphakathi kwezicaciso ezilinganiselwe ukuze ugweme ukulimala komlilo noma komkhiqizo.
7. Hlanza isilawuli ngendwangu eyomile futhi ugweme ukusebenzisa amanzi noma i-organic solvent ukuvimbela umlilo noma ukushaqeka kukagesi.
8. Gcina umkhiqizo kude ne-chip yensimbi, uthuli, nezinsalela zocingo ezigelezela kuyunithi engase ibangele umlilo noma umonakalo womkhiqizo.
9. Ungasiqeqeshi noma usiguqule isilawuli ukuze uvimbele umlilo noma ukushaqeka kukagesi.

Isingeniso

Siyabonga ngokukhetha umkhiqizo wethu we-Autonics. Funda futhi uqonde incwadi yeziqondiso kanye nemanuwali kahle ngaphambi kokusebenzisa umkhiqizo. Ukuze uphephe, funda futhi ulandele ukucatshangelwa kokuphepha okungezansi ngaphambi kokusebenzisa. Ukuze uphephe, funda futhi ulandele ukucatshangelwa okulotshwe encwadini yeziqondiso, amanye amamanuwali nama-Autonics webindawo. Gcina le manuwali yeziqondiso endaweni lapho ungathola khona kalula. Ukucaciswa, ubukhulu, njll kungashintsha ngaphandle kwesaziso sokuthuthukiswa komkhiqizo Amanye amamodeli angayekwa ngaphandle kwesaziso. Landela i-Autonics webindawo yemininingwane yakamuva.

Ukucatshangelwa Kokuphepha

• Bheka konke 'Ukucatshangelwa Kokuphepha' ukuze usebenze ngendlela ephephile futhi efanele ukugwema izingozi.
• uphawu lubonisa ukuqapha ngenxa yezimo ezikhethekile lapho izingozi zingase zenzeke.

Isexwayiso Ukwehluleka ukulandela imiyalelo kungase kubangele ukulimala okubi kakhulu noma ukufa

1. Idivayisi ehluleka ukuphepha kufanele ifakwe uma kusetshenziswa iyunithi enemishini engase ibangele ukulimala okubi kakhulu noma ukulahlekelwa okukhulu komnotho. amadivaysi, njll.) Ukwehluleka ukulandela lo myalelo kungase kubangele ukulimala komuntu siqu, ukulahlekelwa kwezomnotho noma umlilo.
2. Ungayisebenzisi iyunithi endaweni lapho igesi evuthayo/eqhumayo/ebolayo, umswakama ophezulu, ukukhanya kwelanga okuqondile, ukushisa okukhazimulayo, ukudlidliza, umthelela noma usawoti omningi. Ukwehluleka ukulandela lo myalelo kungase kubangele ukuqhuma noma umlilo.
3. Faka kuphaneli yedivayisi ozoyisebenzisa. Ukwehluleka ukulandela lo myalelo kungase kubangele ukushaqeka kukagesi.
4. Ungaxhumeki, ulungise, noma uhlole iyunithi ngenkathi uxhume kumthombo wamandla. Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma ukushaqeka kukagesi.
5. Hlola 'Ukuxhuma' ngaphambi kwezintambo. Ukwehluleka ukulandela lo myalo kungaholela emlilweni.
6. Ungaliqeqeshi noma uliguqule iyunithi. Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma ukushaqeka kukagesi.

Isexwayiso Ukwehluleka ukulandela imiyalelo kungase kubangele ukulimala noma ukulimala komkhiqizo

1. Uma uxhuma okokufaka kwamandla kanye nokuphumayo kwe-relay, sebenzisa ikhebuli engu-AWG 20 (0.50 mm2) noma ngaphezulu, futhi uqinise isikulufu setheminali ngetorque eqinisayo engu-0.74 kuya ku-0.90 N m. Uma uxhuma ikhebuli yenzwa neyokuxhumana ngaphandle kwekhebula elizinikele, sebenzisa ikhebuli engu-AWG 28 ukuya ku-16 futhi uqinise isikulufu setheminali ngetorque eqinisayo engu-0.74 ukuya ku-0.90 N m. Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma ukungasebenzi kahle ngenxa yokwehluleka ukuxhumana.
2. Sebenzisa iyunithi ngaphakathi kokucaciswa okulinganiselwe. Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma umonakalo womkhiqizo
3. Sebenzisa indwangu eyomile ukuhlanza iyunithi, futhi ungasebenzisi amanzi noma i-organic solvent. Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma ukushaqeka kukagesi.
4. Gcina umkhiqizo kude ne-chip yensimbi, uthuli, nezinsalela zocingo ezigelezela kuyunithi. Ukwehluleka ukulandela lo myalelo kungase kubangele umlilo noma umonakalo womkhiqizo.

Izixwayiso ngesikhathi sokusetshenziswa

• Landela imiyalelo kokuthi 'Izixwayiso ngesikhathi sokusebenzisa'. Uma kungenjalo, kungase kubangele izingozi ezingalindelekile.
• Hlola i-polarity yamatheminali ngaphambi kokufaka izintambo zenzwa yezinga lokushisa. Ngenzwa yezinga lokushisa ye-RTD, yifake ngentambo njengohlobo lwezintambo ezi-3, usebenzisa amakhebuli awugqinsi nobude obufanayo. Ngenzwa yethempelesha ye-thermocouple (TC), sebenzisa intambo yesinxephezelo emisiwe ukuze unwebe intambo.
• Gcina kude nevolumu ephezulutagolayini be-e noma izintambo zikagesi ukuvimbela umsindo ongenisayo. Uma kufakwa ulayini wamandla kanye nolayini wesignali wokufaka eduze, sebenzisa isihlungi somugqa noma i-varistor kulayini wamandla kanye nentambo evikelekile kulayini wesiginali yokufaka. Ungasebenzisi eduze kwesisetshenziswa esikhiqiza amandla kazibuthe anamandla noma umsindo wefrikhwensi ephezulu.
• Ungasebenzisi amandla weqile lapho uxhuma noma unqamula izixhumi zomkhiqizo.
• Faka iswishi yamandla noma i-circuit breaker endaweni efinyeleleka kalula ukuze unikeze noma unqamule amandla.
• Ungasebenzisi iyunithi ngezinye izinjongo (isb. voltmeter, ammeter), kodwa izinga lokushisa
  isilawuli.
• Uma ushintsha inzwa yokufaka, cisha amandla kuqala ngaphambi kokushintsha. Ngemva kokushintsha
  inzwa yokufaka, shintsha inani lepharamitha ehambisanayo.
• 24 VAC, 24-48 VDC Ukunikezwa kwamandla kufanele kufakwe i-insulated kanye nevolumu elinganiselwetagi-e/current noma i-Class 2, idivayisi yokunikeza amandla ka-SELV.
• Ungadluleli kulayini wokuxhumana kanye nentambo kagesi. Sebenzisa izintambo ezimbili ezisontekile kulayini wokuxhumana futhi uxhume ubuhlalu be-ferrite ekugcineni komugqa ukuze unciphise umphumela womsindo wangaphandle.
• Yenza indawo edingekayo ezungeze iyunithi ngemisebe yokushisa. Ngokwesilinganiso sokushisa esinembile, fudumeza iyunithi ngaphezulu kwemizuzu engama-20 ngemuva kokuvula amandla.
• Qinisekisa ukuthi ukunikezwa kwamandla kagesi voltage ifinyelela ku-voltage elinganiselwetage phakathi kwamasekhondi angu-2 ngemva kokunikeza amandla.
• Ungafaki ucingo kumatheminali angasetshenziswanga.
• Le yunithi ingasetshenziswa ezindaweni ezilandelayo.
  • Ngaphakathi (kwisimo semvelo sikalwe 'Ngezici')
  • I-Altitude Max. 2,000 m
  • Idigri yokungcola 2
  • Isigaba sokufakwa II

Uku-oda Ulwazi
Lokhu okokubhekisela kuphela, umkhiqizo wangempela awusekeli zonke izinhlanganisela. Ukuze ukhethe imodeli eshiwo, landela i-Autonics webindawo .

Usayizi

• N: I-DIN W 48 × H 24 mm
• SP: I-DIN W 48 × H 48 mm (uhlobo lwepulagi yamaphini angu-11)
• S: I-DIN W 48 × H 48 mm
• M: I-DIN W 72 × H 72 mm
• W: I-DIN W 96 × H 48 mm
• H: I-DIN W 48 × H 96 mm
• L: I-DIN W 96 × H 96 mm

Inketho yokungena/yokukhiphayo

Usayizi: N
PN	OUT2	Umsebenzi
1	Uhlobo olujwayelekile 01)	Okokufaka kwe-alamu 1 + CT
	Ukushisa Nokuphola	I-alamu 2
2	Uhlobo olujwayelekile	I-alamu 1 + I-alamu 2
D	Uhlobo olujwayelekile	I-alamu 1 + Okokufaka kwedijithali 1/2
	Ukushisa Nokuphola	Okokufaka kwedijithali 1/2
R	Uhlobo olujwayelekile	I-alamu 1+Transmission okukhiphayo
	Ukushisa Nokuphola	Ukudluliswa kokukhipha
T	Uhlobo olujwayelekile	Okukhipha i-alamu 1 + RS485 ukuxhumana
	Ukushisa Nokuphola	Ukuxhumana kwe-RS485

Usayizi: Umsebenzi we-SP PN 1 I-alamu 1

Usayizi: S, M, W, H, L
PN	Umsebenzi
1	I-alamu 1
2	I-alamu 1 + I-alamu ephumayo 2
R	I-alamu 1 + Ukukhipha okukhiphayo
T	Ukuxhumana kwe-alamu 1 + RS485
A	I-alamu 1 + I-alamu 2 + Ukukhipha okukhiphayo
B	I-alamu 1 + Alarm 2 + RS485 ukuxhumana
D	I-alamu 1 + I-alamu 2 + Okokufaka kwedijithali 1/2 02)

1. Imodeli yokufaka ye-CT ye-TK4N ingakhethwa kuphela kumodeli yohlobo oluvamile ngokuphuma kwe-alamu 1. (ngaphandle kwe-TK4SP)
2. Ku-TK4S-D kuphela, ukuphela kwe-OUT2 okukhiphayo kusetshenziswa njengetheminali yokufaka ye-DI-2.
3. Uma imodi yokusebenza ingukulawula kokushisisa noma ukupholisa, i-OUT2 ingasetshenziswa njengokuphuma kwe-alamu 3 (ngaphandle kwe-TK4N).
4. Uma imodi yokusebenza ingukulawula kokushisisa noma ukupholisa, i-OUT2 ingasetshenziswa njengokuphuma kokudlulisela 2.

Ithengiswa Ngokuhlukana

• 11 pin isokhethi: PG-11, PS-11 (N)
• I-Transformer yamanje (CT)
• Ikhava yokuvikela yetheminali: Ikhava ye-RSA / RMA / RHA / RLA
• Isiguquli sokuxhumana: Uchungechunge lwe-SCM

Imininingwane

Uchungechunge		I-TK4N	I-TK4SP	I-TK4S	I-TK4M
Amandla hlinzeka	Uhlobo lwe-AC	100 – 240 VAC 50/60 Hz ±10%
	Uhlobo lwe-AC/DC	–	24 VAC 50/60 Hz ±10%, 24-48 VDC ±10%
Amandla ukusetshenziswa	Uhlobo lwe-AC	≤ 6 VA	≤ 8 VA
	Uhlobo lwe-AC/DC	–	AC: ≤ 8 VA, DC ≤ 5W
Isisindo seyunithi (ipakishiwe)		≈ 70 g (≈ 140 g)	≈ 85 g (≈ 130 g)	≈ 105 g (≈ 150 g)	≈ 140 g (≈ 210 g)

Uchungechunge		I-TK4W	I-TK4H	I-TK4L
Amandla hlinzeka	Uhlobo lwe-AC	100 – 240 VAC 50/60 Hz ±10%
	Uhlobo lwe-AC/DC	24 VAC 50/60 Hz ±10%, 24-48 VDC ±10%
Amandla ukusetshenziswa	Uhlobo lwe-AC	≤ 8 VA
	Uhlobo lwe-AC/DC	AC: ≤ 8 VA, DC ≤ 5W
Isisindo seyunithi (ipakishiwe)		≈ 141 g (≈ 211 g)	≈ 141 g (≈ 211 g)	≈ 198 g (≈ 294 g)

Sampisikhathi sokulala		50 ms
Ukucaciswa kokokufaka		Bheka 'Uhlobo Lokufaka Nokusebenzisa Ububanzi'
Okokufaka kwenketho	Okokufaka kwe-CT	• 0.0-50.0 A (ibanga lokulinganisa eliyinhloko lamanje) • Isilinganiso se-CT: 1/1,000 • Ukunemba kwesilinganiso: ±5% FS ±1dijithi
	Okokufaka kwedijithali	• Othintana naye – VULIWE: ≤ 2 kΩ, VALIWE: ≥ 90 kΩ • Abangaxhunywanga – ivolumu eyinsalelatage ≤ 1.0 V, ukuvuza kwamanje ≤ 0.1 mA • Ukuphuma kwamanje: ≈ 0.5 mA okokufaka ngakunye
Lawula okukhiphayo	I-Relay	250 VAC 3 A, 30 VDC 3 A 1a
	I-SSR	11 VDC±2 V, ≤ 20 mA
	Okwamanje	I-DC 4-20 mA noma i-DC 0-20 mA (ipharamitha), Ukumelana nomthwalo: ≤ 500 Ω
I-alamu okukhiphayo	I-Relay	I-AL1, AL2: 250 VAC 3 A 1a • I-TK4N AL2: 250 VAC 0.5 A 1a (≤ 125 VA)
Okukhipha inketho	Ukudluliswa	I-DC 4 – 20 mA (Ukumelana nomthwalo: ≤ 500 Ω, Ukunemba kokuphumayo: ±0.3% FS)
	RS485 com.	I-Modbus RTU
Uhlobo lokubonisa		7 ingxenye (obomvu, oluhlaza, ophuzi), uhlobo lwe-LED
Uhlobo lokulawula	Ukushisisa, Ukupholisa	VULIWE/VAMILE, P, PI, PD, PID Control
	Ukushisisa & Ukupholisa
I-Hysteresis		• I-Thermocouple, i-RTD: 1 ukuya ku-100 (0.1 kuya ku-100.0) ℃/℉ • I-Analog: idijithi engu-1 ukuya kweyi-100
Ibhendi ye-Proportional (P)		0.1 kuye ku-999.9 ℃/℉ (0.1 kuya ku-999.9%)
Isikhathi esibalulekile (I)		0 kuya ku-9,999 isekhondi
Isikhathi sokuphuma (D)		0 kuya ku-9,999 isekhondi
Umjikelezo wokulawula (T)		• Ukukhishwa kwe-relay, ukuphuma kwedrayivu ye-SSR: 0.1 kuya ku-120.0 isekhondi • Okukhiphayo okukhethekayo kwedrayivu yamanje noma ye-SSR: 1.0 ukuya ku-120.0 isekhondi
Ukusetha kabusha mathupha		0.0 ukuya ku-100.0%
Umjikelezo wokuphila odluliselwe	Omakhenikha	OUT1/2: ≥ 5,000,000 imisebenzi AL1/2: ≥ 20,000,000 imisebenzi (TK4H/W/L: ≥ 5,000,000 imisebenzi)
	Ezogesi	≥ 100,000 imisebenzi
Amandla e-Dielectric		Kuncike ekunikezeni amandla
Ivolumu ye-ACtage uhlobo		Phakathi kwengxenye yokushaja nekesi: 3,000 VAC ~ 50/60 Hz iminithi elingu-1
I-AC / DC ivolumutage uhlobo		Phakathi kwengxenye yokushaja nekesi: 2,000 VAC ~ 50/60 Hz iminithi elingu-1
Ukudlidliza		0.75 mm amplitude imvamisa ka-5 kuye ku-55 Hz ku-X, Y, Z ngayinye isiqondiso amahora angu-2
Ukumelana ne-insulation		≥ 100 MΩ (500 VDC megger)
Ukungavikeleki komsindo		±2 kV umsindo oyisikwele oyisikwele ngesifanisi somsindo (ububanzi be-pulse: 1 ㎲) Isigaba se-R, isigaba se-S
Ukugcinwa kwememori		≈ iminyaka eyi-10 (uhlobo lwenkumbulo ye-semiconductor engaguquki)
Izinga lokushisa le-ambient		-10 kuya ku-50 ℃, isitoreji: -20 kuya ku-60 ℃ (akukho ukuqandisa noma ukujiya)
Umswakama we-ambient		35 kuya ku-85%RH, isitoreji: 35 kuya ku-85%RH (akukho ukuqandisa noma ukujiya)
Isakhiwo sokuvikela		IP65 (Iphaneli yangaphambili, amazinga e-IEC) • I-TK4SP: IP50 (Iphaneli yangaphambili, amazinga e-IEC)
Uhlobo lwe-insulation		Ukufakwa kabili noma ukwahlukanisa okuqinisiwe (maka: , amandla e-dielectric phakathi kwengxenye yokukala nengxenye yamandla: 2 kV)
Isesekeli		Ubakaki, ikhava yokuvikelwa kwetheminali (TK4N)
Ukugunyazwa

Isixhumanisi Esibonakalayo

RS485

Comm. umthetho olandelwayo	I-Modbus RTU
Uhlobo lokuxhuma	RS485
Izinga lokusebenza	Ukuhambisana ne-EIA RS485
Ubuningi bokuxhumana	Amayunithi angama-31 (ikheli: 01 kuya ku-99)
Indlela evumelanisiwe	Asynchronous
Comm. Indlela	I-double-wire half duplex
Comm. uhla olusebenzayo	≤ 800 m
Comm. isivinini	2,400 / 4,800 / 9,600 (okuzenzakalelayo) / 19,200 / 38,400 bps (ipharamitha)
Isikhathi sokuphendula	5 kuya ku-99 ms (okuzenzakalelayo: 20 ms)
Qala kancane	Ibhithi elingu-1 (elilungisiwe)
Idatha kancane	Ibhithi elingu-8 (elilungisiwe)
Ubunye kancane	Akukho (okuzenzakalelayo), Okungajwayelekile, Ngisho
Yima kancane	1 bit, 2 bit (okuzenzakalelayo)
Umjikelezo wokuphila we-EEPROM	≈ 1,000,000 imisebenzi (Sula / Bhala)

Uhlobo Lokufaka kanye Nokusetshenziswa Kwebanga

Uhla lwamasethingi lwamanye amapharamitha lunomkhawulo uma usebenzisa isibonisi sephoyinti ledesimali.

Uhlobo lokokufaka		Idesimali iphuzu	Bonisa	Ukusebenzisa ububanzi (℃)			Ukusebenzisa ububanzi (℉)
Thermo -umbhangqwana	I-K (CA)	1	KCaH	-200	ku	1,350	-328	ku	2,462
		0.1	I-KCaL	-199.9	ku	999.9	-199.9	ku	999.9
	I-J (IC)	1	I-JIcH	-200	ku	800	-328	ku	1,472
		0.1	I-JIcL	-199.9	ku	800.0	-199.9	ku	999.9
	E (CR)	1	I-ECrH	-200	ku	800	-328	ku	1,472
		0.1	I-ECrL	-199.9	ku	800.0	-199.9	ku	999.9
	I-T (CC)	1	I-TccH	-200	ku	400	-328	ku	752
		0.1	I-TCcL	-199.9	ku	400.0	-199.9	ku	752.0
	B (PR)	1	B PR	0	ku	1,800	32	ku	3,272
	I-R (PR)	1	R PR	0	ku	1,750	32	ku	3,182
	I-S (PR)	1	S PR	0	ku	1,750	32	ku	3,182
	N (NN)	1	N NN	-200	ku	1,300	-328	ku	2,372
	C (TT) 01)	1	C TT	0	ku	2,300	32	ku	4,172
	G (TT) 02)	1	G TT	0	ku	2,300	32	ku	4,172
	I-L (IC)	1	I-LIcH	-200	ku	900	-328	ku	1,652
		0.1	I-LIcL	-199.9	ku	900.0	-199.9	ku	999.9
	U (CC)	1	UCCH	-200	ku	400	-328	ku	752
		0.1	UCCL	-199.9	ku	400.0	-199.9	ku	752.0
	I-Platinel II	1	I-PLII	0	ku	1,390	32	ku	2,534
I-RTD	ku50 Ω	0.1	CU5	-199.9	ku	200.0	-199.9	ku	392.0
	ku100 Ω	0.1	CU10	-199.9	ku	200.0	-199.9	ku	392.0
	I-JPt100 Ω	1	I-JPtH	-200	ku	650	-328	ku	1,202
		0.1	I-JPtL	-199.9	ku	650.0	-199.9	ku	999.9
	I-DPt50 Ω	0.1	I-DPT5	-199.9	ku	600.0	-199.9	ku	999.9
	I-DPt100 Ω	1	I-DPtH	-200	ku	650	-328	ku	1,202
		0.1	I-DPtL	-199.9	ku	650.0	-199.9	ku	999.9
	I-Nickel 120 Ω	1	NI12	-80	ku	200	-112	ku	392
I-Analog	0 ukuze 10 V	–	I-AV1			0 kuye	10 V
	0 ukuze 5 V	–	I-AV2			0 kuye	5 V
	1 ukuze 5 V	–	I-AV3			1 kuye	5 V
	0 kuya ku-100 mV	–	I-AMV1			0 kuye	100 mV
	0 kuya ku-20 mA	–	AMA1			0 kuye	20 mA
	4 kuya ku-20 mA	–	AMA2			4 kuye	20 mA

1. C (TT): Ngokufanayo nenzwa yohlobo lwe-W5 (TT) ekhona
2. G (TT): Iyafana nenzwa yohlobo lwe-W (TT) ekhona

• Ukumelana komugqa okuvunyelwe ngomugqa ngamunye:

Bonisa ukunemba

Uhlobo lokokufaka	Ukusebenzisa izinga lokushisa	Bonisa ukunemba
Thermo - I-RTD yombhangqwana	Ngezinga lokushisa lekamelo (23℃ ±5 ℃)	(PV ±0.3% noma ±1 ℃ eyodwa ephakeme) ±1-idijithi • I-Thermocouple K, J, T, N, E ngezansi -100 ℃ kanye no-L, U, PII, RTD Cu50 Ω, Dpt50 Ω: (PV ±0.3% noma ±2 ℃ eyodwa ephakeme) ±1 idijithi • I-Thermocouple C, G no-R, S ngaphansi kuka-200 ℃: (PV ±0.3% noma ±3 ℃ eyodwa ephakeme) ±1-idijithi • I-Thermocouple B ngaphansi kuka-400 ℃: Awekho amazinga okunemba
	Ngaphandle kwebanga lokushisa kwegumbi	(PV ±0.5% noma ±2 ℃ eyodwa ephakeme) ±1-idijithi • RTD Cu50 Ω, Dpt50 Ω: (PV ±0.5% noma ±3 ℃ eyodwa ephakeme) ±1 idijithi • I-Thermocouple R, S, B, C, G: (PV ±0.5% noma ±5 ℃ eyodwa ephakeme) ±1-idijithi • Ezinye izinzwa: ≤ ±5 ℃ (≤-100 ℃)
I-Analog	Ngezinga lokushisa lekamelo (23℃ ±5 ℃)	±0.3% FS ±1-idijithi
	Ngaphandle kwebanga lokushisa kwegumbi	±0.5% FS ±1-idijithi

Izincazelo zeyunithi

1. Ingxenye yesibonisi se-PV (Bomvu)
   • Imodi yokuqalisa: Ibonisa i-PV (inani lamanje).
   • Imodi yokusetha: Ibonisa igama lepharamitha.
2. Ingxenye yesibonisi ye-SV (Luhlaza)
   • Imodi yokuqalisa: Ibonisa i-SV (Inani lokusetha).
   • Imodi yokusetha: Ibonisa inani lokusetha ipharamitha.
3. Ukhiye wokufaka

Inkomba

Bonisa	Igama	Incazelo
℃, %, ℉	Iyunithi	Ibonisa iyunithi ekhethiwe (ipharamitha)
AT	Ukushuna okuzenzakalelayo	Iyabaneka ngesikhathi sokushuna okuzenzakalelayo njalo ngesekhondi elingu-1
OUT1/2	Lawula okukhiphayo	IVULA uma okukhiphayo kokulawula KUVULIWE • Okukhiphayo kwe-SSR (ukulawula umjikelezo/isigaba) I-MV ngaphezu kuka-5% IVULIWE • Okukhiphayo kwamanje Ukulawula mathupha: 0% ISELULE, phezu VULIWE Ukulawula okuzenzakalelayo: ngaphansi kuka-2% ISELWE, ngaphezu kuka-3% VULIWE
AL1/2	Okukhipha i-alamu	IVULA uma okukhiphayo kwe-alamu KUVULIWE
INDODA	Ukulawula mathupha	IVULA ngesikhathi sokulawula mathupha
SV1/2/3	I-Multi SV	Inkomba ye-SV IVULIWE okwamanje eboniswayo. (Uma usebenzisa umsebenzi we-SV eminingi)

Imbobo yesilayishi se-PC
Okokuxhuma isiguquli sokuxhumana (uchungechunge lwe-SCM).

• Ukuze uthole imininingwane mayelana nemodeli endala, bheka imanuwali yomsebenzisi. Landa izincwadi ezivela ku-Autonics webindawo.

Ubukhulu

• Iyunithi: mm, Ukuze uthole imidwebo enemininingwane, landela i-Autonics webindawo.
• Ngezansi kusekelwe ku-TK4S Series

 

Ubakaki

Ikhava yokuvikela itheminali

Indlela Yokufaka

• Ngemva kokukhweza umkhiqizo kuphaneli ngobakaki, qinisa amabhawodi usebenzisa isikrudrayiva.
• Faka iyunithi kuphaneli, qinisa ubakaki ngokuphusha nge-screwdriver ye-flathead.

Amaphutha

Bonisa	Okokufaka	Incazelo	Okukhiphayo	Ukuxazulula inkinga
	Inzwa yezinga lokushisa	Ikhanya ngesikhawu samasekhondi angu-0.5 lapho inzwa yokufaka inqanyulwa noma inzwa ingaxhumekile.	'Iphutha lenzwa, MV' inani lokusetha ipharamitha	Hlola isimo sesizweli sokufaka.
VULA
	I-Analog	Ibaneka ngesikhawu sesekhondi elingu-0.5 uma okokufaka kungaphezu kwe-FS ±10%.	'Iphutha lenzwa, Ipharamitha ye-MV ukusetha inani	Hlola isimo sokufakwayo kwe-analogi.
	Inzwa yezinga lokushisa	Ibaneka ngezikhawu zamasekhondi angu-0.5 uma inani lokokufaka lingaphezu kobubanzi bokufaka.	Ukushisisa: 0%, Ukupholisa: 100%
HHHH
	I-Analog	Ibaneka ngezikhawu zamasekhondi angu-0.5 uma i inani lokufakwayo lingaphezu kuka-5 kuya ku-10% wokuphakama umkhawulo noma inani eliphansi lomkhawulo.	Okukhipha okujwayelekile	Lapho okokufaka kungaphakathi kwebanga lokufaka elinganisiwe, lesi sibonisi siyanyamalala.
	Inzwa yezinga lokushisa	Ikhanya ngo-0.5 sec. izikhawu uma inani lokokufaka lingaphansi kobubanzi bokufaka.	Ukushisisa: 100%, Ukupholisa: 0%
I-LLLL
	I-Analog	Ibaneka ngezikhawu zamasekhondi angu-0.5 uma i inani lokokufaka lingaphezu kuka-5 kuya ku-10% of low umkhawulo noma inani eliphezulu lomkhawulo.	Okukhipha okujwayelekile
IPHUTHA	Inzwa yezinga lokushisa	Ibaneka ngezikhawu ezingamasekhondi angu-0.5 uma kunephutha lokusetha futhi ibuyela kuphutha-ngaphambi kwesikrini.	–	Hlola indlela yokusetha.
	I-Analog

Ukuxhumana

• Amatheminali anomthunzi ayimodeli evamile.
• Okokufaka kwedijithali akuvalwa ngogesi kusuka kumasekhethi angaphakathi, ngakho-ke kufanele kugqunywe lapho kuxhunywa amanye amasekhethi.

I-TK4N

I-TK4S

I-TK4SP

I-TK4M

TK4H / W / L

Imininingwane ye-Crimp Terminal

• Iyunithi: mm, Sebenzisa itheminali ye-crimp yomumo wokulandela.

Isibonisi Sasekuqaleni Lapho Amandla Evuliwe

Uma amandla enikezwa, ngemva kokuthi isibonisi sizokhanyisa isekhondi elingu-1, igama lemodeli liboniswa ngokulandelana. Ngemuva kokuthi uhlobo lwenzwa yokufaka luzokhanya kabili, ngena kumodi ye-RUN.

Ukusetha Imodi

1. Esimeni semodeli ye-TK4N / 4S / 4SP, ukucindezela okufushane kokhiye we-[MODE] kungena esikhundleni somsebenzi wokhiye ongu-[A/M].

Ukusetha Ipharamitha

• Amanye amapharamitha ayenziwa asebenze/angasebenzi kuye ngemodeli noma ukulungiselelwa kwamanye amapharamitha.
• Isici esithi 'Imaski Yepharamitha', esifihla amapharamitha angadingekile noma angasebenzi, kanye nesici 'seqembu lepharamitha yomsebenzisi', esisetha ngokushesha futhi kalula amapharamitha athile asetshenziswa njalo, singasethwa ku-DAQMaster.
• Bheka kumanuwali yomsebenzisi ukuze uthole imininingwane.

Ipharamitha 1 iqembu

Ipharamitha 2 iqembu

Ipharamitha 3 iqembu

Ipharamitha 4 iqembu

Ipharamitha 5 iqembu

18, Bansong-ro 513Beon-gil, Haeundae-gu, Busan, Republic of Korea, 48002  www.kuzithin.com | +82-2-2048-1577 | sales@autonics.com

Amadokhumenti / Izinsiza

I-Autonics TCD210240AC Izilawuli Zezinga lokushisa ze-PID ngesikhathi esisodwa kanye Nokupholisa [pdf] Incwadi Yeziqondiso I-TCD210240AC Izilawuli Zezinga lokushisa Zokushisisa kanye Nokupholisa Ngasikhathi sinye ze-PID, TCD210240AC, Izilawuli Zezinga lokushisa ezihambisanayo ze-PID, Izilawuli ze-PID zokushisisa nokupholisa, Izilawuli ze-PID zokupholisa, Izilawuli Zezinga lokushisa, Izilawuli Zezinga lokushisa ID rs

Izithenjwa

• Imaniwali yosebenzisayo