Ubuy DC 12V 4-Wire PWM Fan Temperature Controller

Imiyalo yokusetshenziswa komkhiqizo

• Use the buttons on the controller for various functions such as switching display parameters, increasing or decreasing parameter values, and setting PWM parameters.
• Set the ‘L**’ Accelerated Temperature, ‘H**’ Full Speed Temperature, and ‘C**’ Shutdown Temperature to control the fan speed based on temperature thresholds.
• Configure the PWM output time sequence by pressing the ‘OK’ button and using the ‘+’ and ‘-‘ buttons to switch between values P1 or P-1.

DC 12V 4-Wire PWM Fan Isilawuli Sezinga lokushisa

Incazelo

• It is a DC 12V 4-Wire PWM Fan Temperature Controller. 3Bit red LED digital display screen shows temperature and speed which can be used for Host box, CPU, Server host, etc.

Izici

1. 4-Wire Fan Dedicated Controller
2. 100% PWM Speed Control
3. Support Reverse Time Sequence Fan
4. Support 3A Fan Low Temperature Shutdown
5. Temperature and Speed Dual Display
6. Power-OFF Parameter Memory Function

Amapharamitha

• Ukusebenza Voltage: DC 8V-16V ( Recommend 12V)
• Working Current: <40mA at 12V
• Drive Current: <3.5A
• PWM Range: 1%~100% (+/-0.5% )
• Imvamisa ye-PWM: 25KHz (+/-1KHz)
• I-PWM Ampamandla: 5V lapho alayishiwe
• Measure Temperature: -9.9C~99.9C Celsius Degree
• Temperature Error : +/-1.2C at 0C~50C and +/-2C at others
• Inzwa Yezinga lokushisa: NTC 10K B=3590 Inzwa
• Sensor Length : 40cm
• Usayizi wemojuli: 60*29*21mm

Button Set Method

1. ’ + ’ Button : Switch display parameters at Normal Running State; Increase parameter value at Parameter Set State. Keep press to increase parameter values quickly and continuously at Parameter Set State.
2. ’ – ’ Button : Switch display parameters at Normal Running State; Decrease parameter value at Parameter Set Mode. Keep press to decrease parameter values quickly and continuously at Parameter Set State.
3. ’ OK ’ Button :
   1. >.At Normal Running State: Short-press enter into Set PWM Parameter State. Then press ‘ + ’ and ‘ – ’ buttons to change the parameter value and set range is 1% to 100%. Short-press again to save value and exit.
   2. >.At Normal Running State: Keep press 2 second enter into Set Temperature State. Then short-press press ‘ OK ’ button to switch parameters ‘ L** ’, ‘ H** ’, ‘ C** ’. Press ‘ + ’ and ‘ – ’ buttons to change the parameter value. Short press ‘ OK ’ button again to save value and exit.
   3. >.Set PWM OUT Time Sequence: Keep pressing ‘ OK ’ button and then turn ON the working power supply, then enter into set mode for PWM OUT Time Sequence. Press the‘ + ’ and ‘ – ’ buttons to switch the value of P1 or P-1. Press ‘ OK ’ button again to save value and exit.
      1. >. P1 : Forward Output, Default Normal PWM OUT Time Sequence.
      2. >. P-1: Reverse PWM OUT Time Sequence.

Temperature Parameter Set

1. ‘ L** ’ Accelerated Temperature: Set range is 5~94. PWM output increases with temperature rise when the measured temperature higher than‘ L** ’.
2. ‘ H** ’ Full Speed Temperature: Set range is 10~99. PWM keep output 100% and fan keeps running at full speed.
3. ‘ C** ’ Shutdown Temperature:
   1. Ibanga elimisiwe lingu-0~92.
   2. Enable this function if ‘ C** ’ >0;
   3. Disable this function if this parameter is set to ‘ C00 ’. Fan keep work and PWM keep output.
   4. Turn OFF fan( both fan power and PWM signal are turn off) ;
   5. At Shutdown State: Fan restarts and speed changes with temperature if when the measured temperature higher than ‘ L** ’ Accelerated Temperature.
4. Note-1: The difference between ‘ L** ’ Accelerated Temperature and ‘ H** ’ Full Speed Temperature cannot be less than 5.
5. Note-2: The difference between ‘ L** ’ Accelerated Temperature and ‘ C** ’ Shutdown Temperature cannot be less than 2.
6. Note-3: if the difference does not meet the requirements when setting parameters, the program will automatically adjust the other two parameters.

Isicelo

1. I-Industrial Automation Control
2. Umshini we-CNC
3. Host box, CPU, Server host
4. Isivinini umbusi

Iphakheji

1. 1pcs DC 12V 4-Wire PWM Fan Temperature Controller
2. 1pcs 40cm NTC 10K B=3590 Temperature Sensor

FAQ

Q: Ithini ivolumu enconyiwe yokusebenzatage kulesi silawuli?

A: Ivolumu yokusebenza enconyiwetage is DC 12V, with a range of DC 8V-16V.

Q: Ngisetha kanjani isivinini sabalandeli ngokusekelwe kuzinga lokushisa?

A: You can set the L Accelerated Temperature, H Full Speed Temperature, and C Shutdown Temperature parameters to control the fan speed based on temperature thresholds.

Amadokhumenti / Izinsiza

Ubuy DC 12V 4-Wire PWM Fan Temperature Controller [pdf] Iziyalezo DC 12V 4-Wire PWM Fan Temperature Controller, 4-Wire PWM Fan Controller, PWM Fan Controller, Temperature Controller

Izithenjwa

• Imaniwali yosebenzisayo