I-Wizard 2 Shintsha 2 Isilawuli Segeyimu ye-NYXI TMR

Umdlali wegeyimu othandekayo,
Siyabonga ngokuthenga umkhiqizo wethu.
Ngaphambi kokusebenzisa umkhiqizo, sicela ufunde imanuwali yomkhiqizo ngokucophelela.

OKUQUKETHWE IPHAKEJI

• NJ10 Left Controller x1
• NJ10 Right Controlle x1
• NJ10 Middle Bridge x1
• Multi-function Receiver x1
• Ikhebuli yokushaja ye-USB-C x1
• Receiver Extension Cable x 1

IMIHLABA YOBUCHWEPHESHE

• Ukuxhumana: Bluetooth 5.0, 2.4G
• Wireless Battery Capacity: 400mAh (per controller)
• Iyashaja: 5V/0.4A nge-USB-C
• Izinto zokwakha: PC + ABS + Metal + Silicone
• Isisindo: 225g
• Usayizi: 106*155*55,smm

I-Specification DIAGRAM

CONNECTING TO NINTENDO SWITCH

1. Slide the controller downward along the rails on both sides of the console screen until it clicks. The “Controllers” interface on the console will display connected left/right controllers.
2. To remove the controller, press the release button on the back of the controller and slide it upward.
3. When the console is powered on, detaching the controller from the rails will automatically establish a Bluetooth connection with the Switch.
4. When the console is powered off, detach the controller from the rails and press the Home Button to power on and reconnect.
5. After successfully connecting to Switch, the controller vibrates for 1 second.

RECEIVER CONNECTION TO PC

(XINPUT MODE)

1. Press and hold the Home Button for 3 seconds to power on. LEDs 1-4 on both controllers will flash green sequentially.
2. Insert the receiver into the PC and press and hold its button until the LED blinks rapidly.
3. Linda ukubhanqa.

(DINPUT MODE)

1. In Xinput mode, press and hold A+ B + Home to switch to Dinput mode. LEDs 1-4 will blink green three times.
2. Repeat the same key combination to switch back to Xinput mode.

RECEIVER CONNECTION TO PC/NGC
Press and hold the home button of the right handle for 5 seconds to tum on the device, and the LED1-4 of the right handle will flash green.

Plug the receiver into the computer, and press and hold the button on the receiver until the LED flashes quickly.

Wait for the right handle and receiver to pair successfully, and the LED lights of the receiver and the handle will be on.

Press and hold the button on the receiver again until the LED flashes quickly, and press and hold the screen button on the left handle for 5 seconds until the LED1-4 of the left handle flashes green.

Wait for the left handle and receiver to pair successfully before it can be used normally.

RECEIVER CONNECTED TO WII
Tum on the Wii console, enter the game, and connect the original controller. After entering the game, unplug the original adapter, and then plug the NJ10 receiver into the console, and press and hold the button on the receiver until the LED flashes quickly.
Press and hold the home button of the right handle for 5 seconds to tum on the device, and the LED1-4 of the right handle will flash green.
Wait for the right handle and receiver to pair successfully, and the LED lights of the receiver and the handle will be on.

Long press the button on the receiver again until the LED flashes quickly, and long press the screen button on the left handle for 5 seconds until the left handle LED1-4 flashes green water.

JOYSTICK CALIBRATION

1. Press SL+ SR+ + Button (left controller: – Button) to enter calibration mode. Rotate the joysticks and press the same keys again to exit. A 1-second vibration confinns completion.
2. Switch System Calibration: Navigate to Settings> Controllers & Sensors Calibrate Control Sticks and follow on-screen instructions.

I-TRIGGER CALIBRATION

Press SL+ SR+ Home (left controller: Capture Button) to enter calibration mode. Press triggers fully to calibrate. Exit using the same keys (1-second vibration confirms completion).

6-AXIS GYROSCOPE CALIBRATION

1. On Switch: Navigate to Settings> Controllers & Sensors > Calibrate Motion Controls.
2. Place the controller on a flat surface and follow on-screen prompts. Press -and + Buttons to complete calibration.

UMSEBENZI WE-TURBO

1. Supported Buttons: D-pad, A, B, X, Y, L, R, ZL, ZR.
2. Nika amandla i-Turbo: Hold the Setting Button, press a target button, then release.
   LED4 glows white.
3. Lungisa Isivinini: Default is 12Hz (adjustable via app).
4. Khubaza i-Turbo: Press the Setting Button + target button three times (LED4 turns off).

UKUHLELA INKONOBHANA

* Back Buttons (M1/M2): Can be mapped to other buttons or macros (max 21 actions per macro).

1. Ukwenza imephu: Hold Setting Button + target back button for 3 seconds. Press the desired button/macro sequence, then press the back button again to save.
2. Sula imephu: Hold Setting Button + back button for 3 seconds, then press the back button without input.

Umkhiqizi: Shenzhen MIKE Morgen Technology Co.,Ltd
Ikheli: 3/F, Building 5, Block C, Fairview Plaza, Xiangjiaotang Community,Sakata
Umfakisicelo: Inkampani NYXI Gaming Inc
Ikheli: 4520 Centennial Bivd NUM1004, Colorado Sorinas CO 80919
Imodeli: NJ10 FCC ID: 2A88F-NJ10

Isimemezelo Sokuvumelana
Model: NJ10

The product conforms to EC standards for radio interference. Here, Shenzhen MIKE Morgen Technology Co.,Ltd. In Shenzhen announces that NJ10 radio equipment conforms to the Directive. EN IEC 62368-1:2020+A11:2020, EN 50663:2017, EN 62479:2010, ETSI EN 301 489-1 V2.23(2019-11), ETSI EN 301 489-17 V3.2.4(2020-09), ETSI EN 300 328 V2.2.2(2019-07).
Umbhalo ogcwele we-EU Declaration of Compliance ungatholakala kokuthi: www.nyxigame.com

Imodeli: NJ10
I-ID ye-FCC: 2A88F-NJ10

Isitatimende se-FCC

1. Le divayisi ithobela Ingxenye 15 Yemithetho ye-FCC. Ukusebenza kungaphansi kwemibandela emibili elandelayo:
   1. Idivayisi ingase ingabangeli ukuphazamiseka okuyingozi.
   2. Ucingo kufanele lwamukele noma yikuphi ukuphazamiseka okutholiwe, okuhlanganisa okungase kubangele ukusebenza okungafuneki.
2. Izinguquko noma ukuguqulwa kule yunithi okungagunyazwanga ngokucacile yinhlangano enesibopho sokuthobelana kungase kuqede igunya lomsebenzisi lokusebenzisa okokusebenza.

Qaphela: Lesi sisetshenziswa sihloliwe futhi satholwa ukuthi sithobela imikhawulo yedivayisi yedijithali Yekilasi C, ngokususelwe Engxenyeni 15 Yemithetho Ye-FCC. Le mikhawulo iklanyelwe ukuhlinzeka ngokuvikeleka okufanele ekuphazanyisweni okuyingozi ekufakweni kwendawo yokuhlala.

This equipment generates, uses, and can radiate radio frequency energy and,if not installed and used in accor dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Hlela kabusha noma hambisa uthi olwamukelayo
• Khulisa ibanga phakathi kwesisetshenziswa nomamukeli.
• Xhuma okokusebenza kusokhethi kusekethe ehlukile kuleyo lapho umamukeli axhumeke khona.
• Xhumana ne-distrbutor yakho noma uchwepheshe werediyo/TV onesipiliyoni ukuze uthole usizo.

Uphawu lusho ukuthi umkhiqizo akufanele ulahlwe nemfucuza yasendlini kodwa ulethwe endaweni efanele yokuqoqwa ukuze uvumele ukugaywa kabusha. Ngokwemithetho yendawo, ungawulahli umkhiqizo noma ibhethri elishajekayo ngodoti ojwayelekile wasendlini.

Ukulahlwa okufanele kwemikhiqizo esetshenzisiwe namabhethri aphinde ashajwe kusiza ukuvimbela imithelela engemihle endaweni ezungezile nempilo yabantu.

IZINYATHELO ZOKUZIVIKELA

Amadokhumenti / Izinsiza

NYXI Wizard 2 Switch 2 NYXI TMR Game Controller [pdf] Imaniwali yosebenzisayo Wizard 2 Switch 2 NYXI TMR Game Controller, Switch 2 NYXI TMR Game Controller, NYXI TMR Game Controller, Game Controller

Izithenjwa

• Imaniwali yosebenzisayo