USimon Standoff
Incwadi Yeziqondiso
USimon Standoff
nguPaola Solórzano Bravo
Iphrojekthi iwumdlalo wabadlali ababili abalingisa umdlalo othandwayo, uSimon. Besifuna ukwenza igeyimu ebandakanya ukusebenzisana nento yethu kodwa futhi nomunye umuntu ngakho lokhu kuzoba ukuphambuka enguqulweni evamile. Umdlalo ubekwe ebhokisini eliphrintiwe nge-laser eliqukethe zonke izingxenye zomdlalo. Isivalo sebhokisi siphinde sisikwe nge-laser futhi sikhishwe izimbobo. Ukusebenzisana kwangempela komdlalo kubandakanya Umdlali 1 kanye Nomdlali 2 abaqhudelanayo ukuze babone ukuthi ubani ongaya kude kakhulu njengoba beqhudelana no-Simon. Bobabili abadlali bazoba nezinkinobho ezi-4 zokukhanyisa ezihlanganisweni phambi kwabo okufanele baziqedele. Umdlali wokugcina ozoqhudelana noSimon uyawina. Wonke ama-LED alotha ngaphezu kwesisodwa ukuze abonise ukuthi umdlali ufake inhlanganisela ngokungalungile noma ulinde isikhathi eside kakhulu. Izinkinobho zokusebenzelana ezesikhashana futhi zine-LED ekhanyisa ngokuyala. Uma igeyimu ingadlalwa, njengoba ama-LED akuzinkinobho engase ahlelwe ukuze ahluke esenzweni sokuchofa inkinobho, azungeza imibala egqamile ukuze ahehe abantu ukuthi badlale. Lo mdlalo nesipiliyoni kuzobeka inkumbulo yomuntu esivivinyweni futhi kuqubule ukuncintisana. 
Izinto zokwakha
- 2x - Ibhodi lesinkwa eligcwele
- 2x – Arduino Nano 33 IoT
- 16x – 330 Ohm Resistors
- 2x – Izinkinobho Zokusunduza Zesikhashana Eziyi-16mm Eziluhlaza okwesibhakabhaka
- 2x – Izinkinobho Zokusunduza Zesikhashana ezingu-16mm ezibomvu
- 2x – Okuphuzi 16mm Izinkinobho Zokusunduza Zesikhashana Ezikhanyayo
- 2x – Okuluhlaza 16mm Izinkinobho Zokusunduza Zesikhashana Ezikhanyisiwe
- 32x – 3 x 45mm Heat Shrink Tube
- I-Solid Core Wire
Ukugcwala Kwezifunda
- Usebenzisa ucezu lwentambo yomgogodla oqinile, xhuma kusuka kuphinikhodi engu-3.3 V ku-Arduino ukuya emugqeni ophozithivu webhodi lezinkwa. Bese, sebenzisa olunye ucezu locingo ukuxhuma yomibili imigqa ephozithivu yebhodi lezinkwa
- Xhuma usuka ku-GND, phansi, phinina ku-Arduino kuya kulayini ongemuhle webhodi lezinkwa. Sebenzisa olunye ucezu locingo ukuxhuma yomibili imigqa engemihle yebhodi lezinkwa
- Sika izingcezu ezingama-32, ezi-4 ngenkinobho ngayinye ekhanyisiwe, cishe ezi-4 ngobude bocingo oluqinile oluwumgogodla
- Hlikihla inkatha engu-1 ohlangothini olulodwa locingo ngalunye futhi cishe u-1 cm ukusuka kolunye uhlangothi locingo ngalunye.
- Khipha oku-1 ohlangothini lwentambo komunye woxhumana nabo ngemuva kwenye yezinkinobho ezikhanyisiwe, njengoba kukhonjisiwe esithombeni esingenhla.
- Phinda izinyathelo zangaphambilini nabo bonke abathintwayo kuzo zonke izinkinobho ezingu-8 ezikhanyisiwe
- Sebenzisa i-soldering iron ukuze udayise ucingo oluqinile oluyizihibe koxhumene nalo olunamathiselwe kuye
- Phinda lokhu ngazo zonke izintambo ezinamathiselwe
- Ukushisa kunciphisa elinye lamashubhu okunciphisa ukushisa phezu kothintana naye ngamunye kanye nentambo yakhe enamathiselwe, njengoba kuboniswe ngenhla
- QAPHELA: othintana naye omakwe + uwuhlangothi oluhle lwe-LED futhi othintana naye umakwe - uhlangothi olunegethivu lwe-LED. Abanye oxhumana nabo ababili kuzoba izintambo zezinkinobho
- Namathisela uhlangothi oluphawulwe kahle lwenkinobho ebomvu ekhanyisiwe emugqeni lapho uzosebenzisa khona ucezu lwentambo eqinile ewumgogodla ukunamathisela iphinikhodi D18 ye-Arduino Nano 33 IoT
- Namathisela uhlangothi oluphawulwe njengenegethivu lwenkinobho ebomvu ekhanyisiwe emugqeni oseduze nomugqa osetshenziswe ngaphambilini lapho uzobeka khona okukodwa kokuphikisayo okungu-330 ohm kuya emugqeni ongemuhle webhodi lezinkwa.
- Namathisela noma yiziphi izintambo ezimbili ezisele phezu kwesihlukanisi esimaphakathi kumugqa lapho uzosebenzisa khona olunye ucezu lwentambo eqinile engumongo ukuze uxhume ku-pin D9 ku-Arduino.
- Kusukela kulowo mugqa ofanayo, xhuma umugqa kanye nomugqa ongemuhle webhodi lezinkwa nge-resistor engu-330 ohm.
- Namathisela intambo esele kumugqa eduze komugqa osetshenziswe esinyathelweni sangaphambilini. Usebenzisa ucezu oluncane lwentambo yomgogodla oqinile, xhuma lo mugqa kumugqa ophozithivu webhodi lezinkwa
- Phinda izinyathelo ezingu-11-15 kuzo zonke ezinye izinkinobho ezikhanyisiwe, okuthintwayo okuphawulwe kahle kwenkinobho ephuzi kuya ku-D19 kanye nokuxhumana kwenkinobho kuya ku-D3, ukuthintana okuphawulwe kahle kwenkinobho eluhlaza kuya ku-D20 kanye nokuxhumana kwenkinobho iya ku-D4, ukuthintana okuphawulwe kahle kwenkinobho eluhlaza okwesibhakabhaka kuya ku-D21 kanye nokuxhumana kwenkinobho kuya ku-D7
Ama-Schematics kanye Nemidwebo Yesifunda
Nakuba imidwebo yohlelo neyesekethe ngenhla ibonisa kokubili ukushintshwa kwesikhashana, izinkinobho, nama-LED njengezingxenye ezihlukene, isifunda sangempela sisebenzisa kuphela izinkinobho ezikhanyisiwe zesikhashana ezikhanyisiwe. Lokhu kungenxa yokuthi ngeshwa, iFritzing ayinazo izinto esizisebenzisile. Izinkinobho ezikhanyisiwe ezisetshenzisiwe zinokubili inkinobho kanye nezingxenye ze-LED ezihlanganisiwe kunokuhlukana.
Ikhodi
Nansi i-.insole yekhodi yokusebenza ye-Arduino.
 |
https://www.instructables.com/ORIG/FAR/IBQN/KX4OZ1BF/FARIBQNKX4OZ1BF.ino | Landa |
I-Laser Cutting
Ekugcineni, isinyathelo sokugcina ukusika ibhokisi nge-laser ukuze uvale amasekhethi. Ibhokisi elisetshenziswe kule phrojekthi ethile lalingu-12″x8″4″. Sebenzisa i-acrylic engu-1/8″ nesisiki se-laser kanye ne-.dxf le ukuze usike phezulu, phansi, nezinhlangothi zebhokisi elingunxande. Phezulu kwebhokisi kufanele kube nezimbobo eziyindilinga ezingu-8 15mm ezinkinobho. Amalunga eminwe anconywa ukwenza i-acrylic ibe lula ndawonye.
Iglue ye-Acrylic noma i-super glue esebenza kupulasitiki ingasetshenziswa ukwenza i-acrylic ihlale ndawonye.
Lokhu kuvele kungenze ngifune ukudlala uSimon oqhudelanayo. Ngangingazi ukuthi kwakuyinto engangifuna ukuyenza leyo.
Amadokhumenti / Izinsiza
 |
ifundisa uSimon Standoff [pdf] Incwadi Yeziqondiso USimon Standoff, uSimon Standoff, Standoff |
