I-MTOL04 Tool Tethers
Ulwazi Lomkhiqizo
Imininingwane:
- Product Name: Tool Tethers
- Model Number: MTOL04
- Ukubuyekeza: G
- Umkhiqizi: Akucacisiwe
Imiyalo yokusetshenziswa komkhiqizo
4.0 Ukufakwa
4.1 Ukuhlola Ngaphambi Kokusetshenziswa:
Before attaching the tool tether to the tool, thoroughly inspect
for missing or damaged parts. Check the webbing, looped ends,
stitching, carabiners, and speed clips for any signs of wear or
damage. If any issues are found, do not use the tool tether.
4.2 Inqubo yokufaka:
Ensure the tool attachment is clean and free of oil, grease, or
debris. Place the Tool Tether away from the functional parts of the
tool. The connection point should face away from the center of
gravity if connected directly to the tool.
4.2.3 Choke-On Installation Procedure:
Pass the nylon loop through an established hole on the tool,
then pass the anchorage end connector through the loop and pull the
tool attachment through to choke down onto the tool. Connect it to
a suitable anchor point.
4.2.4 Carabiner Installation Procedure:
Unscrew the screw gate and attach it to an existing hole on the
tool. Turn the screw gate to lock it in the closed position. If
using a twist lock carabiner, ensure it is fully locked closed.
5.0 Isondlo, Isevisi, kanye Nesitoreji
5.1 Ukunakekela:
No scheduled maintenance is required, except for replacing items
that fail inspection.
5.2 Isevisi:
There are no specific service requirements for this system
ingxenye.
5.3 Isitoreji:
Store the Tool Tethers in a clean, dry, chemical-free
environment away from direct sunlight. Avoid prolonged exposure to
extreme heat conditions.
Imibuzo Evame Ukubuzwa (FAQ)
Q: Is there a weight limit for tools attached using the Tool
Tethers?
A: Do NOT attach tools over 5 lbs (2.3 kg) to a Wrist Anchor or
your full body harness as per the manufacturer’s instructions.
Q: Are there specific requirements for connecting
izingxenye?
A: Only use locking connectors suitable for each application.
Qinisekisa ukuthi konke ukuxhumana kuyahambisana ngosayizi, umumo, namandla.
Ungasebenzisi okokusebenza okungahambisani.
I-Tool Tethers
Incwadi Yokufundisa Yomsebenzisi
SICELA UFUNDE – IMINININGWANE EBALULEKILE YOKUPHEPHA Sicela ufunde futhi uqonde imiyalelo yomkhiqizi wengxenye ngayinye noma ingxenye yohlelo oluphelele. Iziyalezo zomkhiqizi kufanele zilandelwe ngokusetshenziswa okufanele, ukunakekelwa, kanye nokugcinwa kwalo mkhiqizo. Le miyalo kufanele igcinwe futhi igcinwe itholakala ukuze isisebenzi sibhekiswe kuso ngaso sonke isikhathi. Ukushintsha noma ukusetshenziswa kabi kwalo mkhiqizo, noma ukwehluleka ukulandela imiyalelo, kungase kubangele ukulimala okubi kakhulu noma ukufa.
WARNINGS AND LIMITATIONS · Never use the FallTech For Tools® components for personal fall arrest, restraint, or work positioning. · Inspect the FallTech For Tools® components before each use in accordance with the requirements in Section 6 below. · Never modify or alter the FallTech For Tools® components. This includes extending the length or tying knots in the tool tethers. · Never tether any tool or equipment to yourself that weighs more than 5 lbs (2.3 kg). · Never use this products to tether a knife, sharp blade, or other sharp tool. · Immediately inspect the FallTech For Tools® components for damage if the tool has experienced a drop. · Do not use this product on tools or equipment that exceed the rated capacity of the lowest rated component in the FallTech For Tools® system. · Do not use this product if it will interfere with any personal fall protection equipment or the operation of the connected tools or equipment. · Avoid using around moving machinery, thermal, electrical, and/or chemical hazards as contact may cause serious injury or death. · Ensure there is adequate tool drop clearance. The tool fall/swing path must not endanger you or any other workers. · All procedures shown in these instructions are for FallTech For Tools® products only. · Report all incidents of dropped tools to your supervisor or safety coordinator. · Do not use this product in temperatures below -31 degrees F (-35 degrees C) or above 113 degrees F (45 degrees C) 1.0 Description – The FallTech For Tools® Tool Tethers are used to connect to the tool or tool attachment to FallTech® Wrist Attachments and Tool Anchors. 2.0 Application – The FallTech For Tools® Tool Tethers are designed to be used as a component in a dropped object prevention program. The tool tethering system is an assembly of components and subsystems to arrest a tool from an accidental drop. The system typically consists of tool attachment, a tool tether, and a tool anchor. See product labels for maximum load capacity and maximum tether length.
3.0 System Requirements – The FallTech For Tools® Tool Tethers is designed for use by a single tool with a combined weight no greater than 15 lbs (6.8 kg), based on the rating of the attachment. DO NOT exceed the capacity of the lowest rated component in the system.
3.1 Ukuhambisana Kwezinto Ezisetshenziswayo zidizayinelwe ukusetshenziswa nezingxenye ezigunyaziwe namasistimu angaphansi kuphela. Ukushintshwa noma ukushintshwa okwenziwe ngezinto ezingagunyaziwe noma amasistimu angaphansi kungase kubeke engcupheni ukusebenzisana kwezisetshenziswa futhi kungase kuthinte ukuphepha nokuthembeka kwesistimu ephelele.
3.2 Ukwenza Ukuxhumana: Sebenzisa kuphela izixhumi zokukhiya ngalo mshini. Sebenzisa kuphela izixhumi ezifanele uhlelo lokusebenza ngalunye. Qinisekisa ukuthi konke ukuxhumana kuyahambisana ngosayizi, umumo, namandla. Ungasebenzisi okokusebenza okungahambisani. Qinisekisa ukuthi zonke izixhumi zivaliwe futhi zikhiyiwe.
4.0 Installation 4.1 Pre-Use Inspection: Inspect the tool tethers thoroughly for missing or damaged parts before attaching it to the tool. Inspect the webbing, looped ends, and stitching for cuts, fraying, and signs of damage to the materials from excessive wear or abrasion. Inspect the carabiners and speed clips for excessive wear, cracks, or deformities. If any of these conditions exist, remove from service.
4.2 Installation Procedure: Ensure the tool attachment is clean and free of oil, grease, or debris, which could prevent adequate attachment onto the tool or tool attachment. The Tool Tether should be placed away from the functional parts of the tool and the connection point should face away from the center of gravity if connect directly to the tool. See the figures below for the installation steps by type of attachment.
4.2.1 Hard Hat Tether Installation Procedure (Stretch Coil Type): Locate a secure location on the inner suspension, an open hole, or slot on the shell to install the FallTech® Hard Hat Tether. Feed the looped end into the hole or slot and pass the anchorage end connector through the loop to choke down onto the hard hat, see Figure 1. Open the metal clip and securely attach it to a suitable anchor point such as a full body harness.
4.2.2 Hard Hat Tether Installation Procedure (Stretch Web Type): Locate a secure location on the inner suspension, an open hole, or slot on the shell to install the FallTech® Hard Hat Tether. Open the plastic cam buckle to release the webbing from the buckle. Slide the end through and around the hole or slot and feed it back into the cam buckle, see Figure 2. Adjust to the desired length and close the cam buckle. Pull on the web to ensure the connection is secure, detach the plastic speed clip and route the anchorage end to a secure anchor point such as a full body harness.
4.2.3 Choke-On Installation Procedure: Pass the nylon loop through an established hole on the tool, pass the anchorage end connector through the nylon loop and pull the tool attachment through to choke down onto the tool, see Figure 3. Connect to a suitable anchor point. DO NOT attach tools over 5 lbs (2.3 kg) to Wrist Anchor or to your full body harness.
4.2.4 Carabiner Installation Procedure: Unscrew the screw gate and attach to an existing hole, turn the screw gate to lock it in the closed position. If using a twist lock carabiner, ensure it is fully locked closed. DO NOT attach tools over 5 lbs (2.3 kg) to a Wrist Anchor or to your full body harness.
Figure 1 – Stretch Coil Type
Figure 2 – Stretch Web Uhlobo
Figure 3 – Choke On
Le manuwali ihloselwe ukuhlangabezana neMiyalo Yomkhiqizi njengoba kudingwa yi-American National Standards Institute (ANSI), International Safety Equipment Association (ISEA) futhi kufanele isetshenziswe njengengxenye yohlelo lokuqeqesha abasebenzi njengoba kudingwa i-Occupational Safety and Health Administration (OSHA).
MTOL04 Rev G
FallTech 1306 S. Alameda Street Compton, CA 90221, USA © 2025 Tel: 800-719-4619 Ifeksi: 323-752-5613
013125
5.0 Isondlo, Isevisi, kanye Nesitoreji
5.1 Maintenance: No scheduled maintenance is required, other than the replacement of items that fail inspection. 5.2 Service: There are no specific service requirements for this system component. 5.3 Storage: Store in a clean, dry, chemical-free environment out of direct sunlight. Avoid prolonged exposure to extreme heat conditions.
6.0 Ukuhlola - Hlola i-FallTech For Tools® Tool Attachments ngokwenqubo yokuhlola eSigabeni 4.1. Uma kukhona okungavamile kutholakala, susa kusevisi.
Imodeli #
5329A5 5329A25
5330A5 5330A25
I-FallTech Yezicaciso zeTether yethuluzi le-Tools®
Incazelo
Amandla namazinga
Stretch-Coil Hard Hat Tether, Choke-on Cinch-loop and Snap-clip 5/pk Stretch-Coil Hard Hat Tether, Choke-on Cinch-loop and Snap-clip 25/pk
Stretch-web Hard Hat Tether w/Adjuster and Snap-buckle 5/pk Stretch-web Hard Hat Tether w/Adjuster and Snap-buckle 25/pk
Kufika ku-2 lbs (0.9 kg)
5335A5 5335A25
5212A1 5212A5
Hard Hat Tether, 2 lbs, ANSI Stretch-coil with Web, Cinch-loop/Web and Adjuster 18″ 5/pk Hard Hat Tether, 2 lbs, ANSI Stretch-coil with Web, Cinch-loop/Web and Adjuster 18″ 25/pk
Premium Tool Tether, 2 lbs, Stretch-coil with Dual Swivel Alum Carabiners, 1/pk Premium Tool Tether, 2 lbs, Stretch-coil with Dual Swivel Alum Carabiners, 5/pk
Kufika ku-2 lbs (2.3 kg)
ANSI/ISEA 121-2018
5027E
3′ to 4′ Speed-clip Stretch-web Tether 5 lbs, elastic Choke-on Cinch-loop with Steel Screwgate Carabiner 1/pk
5032A
3′ to 4′ Speed-clip Stretch-web Tether 5 lbs, elastic Choke-on Cinch-loop with Alum Twist-lock Carabiner 1/pk
5215A1 5215A5
5043A1
5065A1
Premium Tool Tether, 5 lbs, Stretch-coil with Dual Swivel Alum Carabiners, 1/pk Premium Tool Tether, 5 lbs, Stretch-coil with Dual Swivel Alum Carabiners, 5/pk
Premium Tool Tether, 5 lbs, with Dual Swivel Alum Carabiners, 36″, 1/pk
Premium Tool Tether, 5 lbs, Choke-on Web-loop with Swivel Alum Carabiner, 1/pk
Kufika ku-5 lbs (2.3 kg)
ANSI/ISEA 121-2018
NOT FOR FALL PROTECTION NOT FOR FALL PROTECTION
! WARNING ! Inspect before use. Follow all manuals and instructions. Do not use around moving parts. Do not use at full tension.
Kwenziwe eChina 2017
Model # 5330A5 MAXIMUM LOAD CAPACITY
5 LBS (2.3 KG) Do not use for personal fall protection
Tool Attachment Image
Model # 5329A5 MAXIMUM LOAD
CAPACITY 2 LBS (0.9 KG) persDoonaln fotallusper fotoerction
5041A1
Premium Tool Tether, 5 lbs, Choke-on Cinch-loop with Speed-clip and Swivel Alum Carabiner, 48″, 1/pk
5424A10
Tool Attachment, 5 lbs, Waist Belt Cinch Anchor with D-Ring, 10/pk
NOT FOR FALL PROTECTION NOT FOR FALL PROTECTION
NOT FOR FALL PROTECTION NOT FOR FALL PROTECTION
5029B 5029B10
5030A 5030A10
3′ to 4′ Stretch-web Tether 15 lbs, elastic Choke-on Cinch-loop with Steel Screwgate Carabiner 1/pk 3′ to 4′ Stretch-web Tether 15 lbs, elastic Choke-on Cinch-loop with Steel Screwgate Carabiner 10/pk
3′ to 4′ Stretch-web Tether 15 lbs, elastic Choke-on Cinch-loop with Alum Twist-lock Carabiner 1/pk 3′ to 4′ Stretch-web Tether 15 lbs, elastic Choke-on Cinch-loop with Alum Twist-lock Carabiner 10/pk
5029C
3′ to 4′ Stretch-web Tether 15 lbs with Dual Steel Screwgate Carabiners 1/pk
NOT FOR FALL PROTECTION
Kufika ku-15 lbs
(6.8kg)
5031A
3′ to 4′ Stretch-web Tether 15 lbs with Dual Alum Twist-lock Carabiners 1/pk
NOT FOR FALL PROTECTION
I-ANSI/ISEA
121-2018
5044A1
Premium Tool Tether, 15 lbs, with Dual Swivel Alum Carabiners, 36″, 1/pk
5061A1
Premium Tool Tether, 15 lbs, Choke-on Cinch-loop with Swivel Alum Carabiner, 36″, 1/pk
5066A1 5340A 5340B
Premium Tool Tether, 15 lbs, Choke-on Web-loop with Swivel Alum Carabiner, 1/pk Tool Tether, 40 lbs, Non-stretch, Swivel Aluminum Carabiners, 78″, 1/pk
Tool Tether, 40 lbs, Non-stretch, Choke-loop with Swivel Alum Carabiner, 78″, 1/pk
Kufika ku-40 lbs (18.1 kg)
ANSI/ISEA 121-2018
MTOL04 Rev G
013125
2
Amadokhumenti / Izinsiza
 |
FALLTECH MTOL04 Tool Tethers [pdf] Incwadi Yeziqondiso Rev_G, 013125, MTOL04 Tool Tethers, MTOL04, Tool Tethers, Tethers |