Umdwebo wokufaka

Ngaso sonke isikhathi nqamula ugesi ngaphambi kokufaka noma ukushintsha isibani nangaphambi kokuhlanza noma okunye ukulungisa.

1. Susa into ekhona ephaketheni layo langempela.
2. Separate mounting plate (1c) from canopy removing canopy screws (2f)
3. Attach mounting plate (1c) to electrical junction box (la) using screws provided (1d) in hardware package
4. Ukuze ushintshe ubude bendawo, phusha futhi ubambe i-wire gripper (2g), intambo slayide ibe ubude obufunekayo bese ukhulula isibambi socingo (2g) ukuze sivikeleke (Susa izintambo eziningi uma kudingeka)
5. Secure mounting plate (1c) to mounting surface with anchors (1f) and screws (1e)
6. Yenza ukuxhuma okufanelekile kukagesi (okumnyama kuye kokushisayo okuthi “L”, okumhlophe kuya kokuphakathi nendawo “N”, kugaywe kube “GND”) ngamantongomane ocingo (1b) anikezwe kuphakheji yehadiwe
7. Attach canopy(2a) to mounting plate(1c) with canopy screws(2f) and nuts(2c) , tighten them(2f and 2c).
8. Ubude bocingo lwethoni enhle uma kunesidingo, ngokuphusha futhi ubambe i-wire gripper (2g) bese ulungisa ucingo lube ngobude obufunayo.

1. To shorten the cable-just push the cable up, cable will be locked Automatically.
2. To length the cable-lift up on the cable and push up on the lock while keep the lock depressed, lower the cable to the desired length, release the lock to set.

A: Phusha

Iziqondiso zokusebenza zesilawuli kude esingenantambo ze-LED

I. Key function of remote control

1. ukukhanya kwenkomba
2. Vula
3. ukukhanya +
4. ukukhanya okubandayo
5. umjikelezo
6. Vala
7. ukukhanya -
8. ukukhanya okufudumele
9. ukukhanya kwasebusuku

II. Key instructions

Vula: Isikhathi esifushane lamp lighting, Electricity within 5 s, Long press for the code function, After power on 5 s, Long press has no effect

Vala: Isikhathi esifushane lamp goes out, Electricity within 5s, Long press for clear code function, After power on 5 s, Long press has no effect;

Ukukhanya okubandayo +:

1, Short on time, Turn the cold light fixture on one level, At the same time, the warm light lamp darkens one level, There are 15 levels of cold light from out to full light;
2, Long time, The luminaire is gradually lightened, At the same time, the warm light gradually darkens;

Ukukhanya okufudumele +:

1, Short on time, The warm light fixture should be one step brighter, When the cold light lamp kuba mnyama izinga elilodwa, Kunamazinga ayi-15 okukhanya okufudumele ukusuka ngaphandle kuye ekukhanyeni okugcwele;
2, Long time, The warm luminaire is gradually lightened, At the same time, the cold light gradually darkened;

brightness + :

1, Short on time, Heat and cold light lamps are brighter, There are 11 levels of brightness from lowest to highest;
2, Long time, Cold and warm light lamps and lanterns are gradually brightened;

brightness – :

1, Short on time, Dim the light and cold lamps, Kunamazinga ayi-11 okukhanya ukusuka kokuphezulu kuye kokuphansi;
2, Long time, The cold and warm light lamps are gradually dimmed; cycle: Short press the loop key, The light is Warm, neutral, cold, Nightlight, Four state cycles, Press short to change the state one at a time; night lamp: Cindezela kafushane inkinobho yokukhanya kwasebusuku, Ukukhanya okuphansi kwe-alamp converted to Warm light;

The key light : Key indicator light, The indicator button is pressed;

Qaphela: Enye yezilungiselelo zokukhanya kokushisa nokupholisa, Amakhasimende angazichaza ngokwawo ngokunikezwa kwamandla kanye lamps.

III. Functional specifications

Umsebenzi wemephu

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 imizuzwana. Long press the light button once, LED light flashes slowly once. The code successfully. Then the remote control can control the brightness, cooling and heating of the LED lights with good code.
Note: An LED light is only controlled by the last successful remote control, For example, If an LED 1 ight fixture, There is a new remote control and its code matching is successful, Then the remote control will automatically clear the code with the lamp. But a remote control can be coded and controlled with multiple LED lights,

Umsebenzi wokususa amakhodi

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, imizuzwana engu-4, Long press the Turn off button or nightlight button once, LED light slow flash 2 time, The Ming and Qing dynasties were successful.

Note: The function of code clearing is based on the code matching between the remote control and the lamp, Okwesiboneloample, ezimweni ezilandelayo, isilawuli kude kanye ne-lamp do not have the function of code clearing, If there is no clear code function, A long press to turn off the light has no effect.
(1) The remote control is not coded with the lamp, Then there is no clear code function.
(2) When they had finished coding, they cleared the code, Then there is no clear code function.
(3) They have coded each other, But then came a new remote control that corresponded with the light fixture, Then the remote control and its code function will automatically clear, No clear code function.

1. On switch function,

Abakwa-lamp is normally energized, Power on the 0.5S-2S switch, The light is Warm, neutral, cold, Nightlight, 4 state loop Twitches.

2. Cisha inkumbulo umsebenzi

Sebenzisa isilawuli kude ukuze ulungise ukukhanya kwezibani ze-LED, Ukukhanya kwe-LED lamps kanye nenani lekhodi yesilawuli kude kuzogcinwa kunkumbulo yesilawuli se-LED ngemva kwamandla angu-15S, Vula kabusha ngemva kokuphelelwa amandla futhi ukhanyise i-lamp at its previous brightness, And has the code remote control is still controllable.

Amadokhumenti / Izinsiza

I-Digilog E27 LED Isilawuli kude esilawuliwe esingenantambo Fixture [pdf] Umhlahlandlela wokufaka I-E27 LED Wireless Remote Control Light Fixture, E27, I-LED Wireless Remote Control Light Fixture, Remote Control Light Fixture, Light Fixture, Fixture

Izithenjwa

• Imaniwali yosebenzisayo