Boardcon Embedded CM1126B-P System on Module
Imininingwane
| Isici | Imininingwane |
| CPU | I-Quad-core Cortex-A53 |
| I-DDR | 2GB LPDDR4 (kufika ku-4GB) |
| I-EMMC FLASH | I-8GB (kufika ku-256GB) |
| Amandla | I-DC 3.3V |
| I-MIPI DSI | 4-Umzila |
| I2S | 4-CH |
| I-MIPI CSI | 2-CH 4-Lane |
| I-LCD ye-RGB | 24 bit |
| Ikhamera | 1-CH(DVP) kanye no-2-CH(CSI) |
| I-USB | 2-CH (USB HOST 2.0 and OTG 2.0) |
| I-Ethernet | 1000M GMAC |
| I-SDMMC | 2-CH |
| I-I2C | 5-CH |
| SPI | 2-CH |
| UART | 5-CH, 1-CH(DEBUG) |
| I-PWM | 11-CH |
| I-ADC IN | 4-CH |
| Ibhodi Dimension | 34 x 35mm |
Isingeniso
Mayelana nale Manuwali
Le manuwali ihloselwe ukunikeza umsebenzisi i-overview of the board and its benefits, complete feature specifications, and setup procedures. It contains important safety information as well.
Impendulo kanye nesibuyekezo sale Manuwali
Ukuze sisize amakhasimende ethu azuze ngokugcwele ngemikhiqizo yethu, sihlala senza izinsiza ezengeziwe nezibuyekeziwe zitholakale ku-Boardcon webisiza (www.boardcon.com, www.armdesigner.com). Lokhu kufaka phakathi amamanuwali, amanothi ohlelo lokusebenza, isib sokuhlelaamples, kanye nesoftware ebuyekeziwe nehardware. Ngena ngezikhathi ezithile ukuze ubone ukuthi yini entsha! Uma sibeka phambili umsebenzi kulezi zinsiza ezibuyekeziwe, impendulo evela kumakhasimende iyithonya lokuqala, Uma unemibuzo, ukuphawula, noma ukukhathazeka mayelana nomkhiqizo noma iphrojekthi yakho, sicela ungangabazi ukusithinta ku- support@armdesigner.com.
CM1126B-P Introduction
Isifinyezo
The CM1126B-P system-on-module is equipped with Rockchip’s RV1126B-P, built with a quad-core Cortex-A53, 3.0 TOPs NPU, and RISC-V MCU. It is designed specifically for the IPC/CVR devices, AI Camera devices, intelligent interactive devices, and mini robots. High-performance and low-power solutions can help customers introduce new technologies more quickly and enhance the overall solution efficiency. The smallest size can be put on a 38board. Following the hardware revision from CM1126 (V1) to CM1126B-P (V2), where the SoC is updated to the RV1126B-P, the Reset & OTG_VBUS signals and the WIFI/BT module’s GPIO voltage must operate at a 3.3V logic level.
Izici
I-Microprocessor
- I-Quad-core Cortex-A53 ifika ku-1.6GHz
- 32KB I-cache kanye ne-32KB D-cache yomgogodla ngamunye, 512KB L3 inqolobane
- 3.0 TOPS Neural Process Unit
- RISC-V MCU to support 250ms fast boot
- Ubukhulu be-12M ISP
Inhlangano Yenkumbulo
- I-LPDDR4 RAM ifika ku-4GB
- eMMC kufika ku-256GB
- I-SPI Flash ifika ku-8MB
Isiqophi sevidiyo/Isifaki khodi
- Isekela ukuqoshwa kwevidiyo/ukufaka ikhodi kufika ku-4K@30fps
- Isekela ukukhishwa kwekhodi kwesikhathi sangempela kwe-H.264/265
- Isekela umbhalo wevidiyo we-UHD H.264/265 wesikhathi sangempela
- Usayizi wesithombe kufika ku-8192×8192
Bonisa isistimu engaphansi
- Okukhipha ividiyo
- Isekela imizila emi-4 ye-MIPI DSI kuze kufike ku-2560×1440@60fps
- Supports 24-bit RGB parallel output
- Isithombe ku
- Supports up to 16-bit DVP interface
- Isekela i-interface ye-2ch MIPI CSI 4lanes
I-I2S/PCM/AC97
- I-interface emithathu ye-I2S/PCM
- Sekela i-Mic array Kufika ku-8ch PDM/TDM interface
- Sekela okukhiphayo komsindo we-PWM
I-USB ne-PCIE
- Izixhumi ezibonakalayo ezimbili ze-2.0 USB
- One USB 2.0 OTG and one 2.0 USB host
I-Ethernet
- I-RTL8211F
- Sekela 10/100/1000M
I-I2C
- Kufika kuma-I2C amahlanu
- Sekela imodi ejwayelekile nemodi esheshayo (kufika ku-400kbit/s)
I-SDIO
- Sekela iphrothokholi ye-2CH SDIO 3.0
SPI
- Kufikela kuzilawuli ezimbili ze-SPI,
- Isixhumi esibonakalayo se-serial esine-duplex egcwele
UART
- Sekela ama-UART angu-6
- I-UART2 enezintambo ezingu-2 zamathuluzi okulungisa iphutha
- Embedded two 664-byte FIFOs
- Sekela imodi yokulawula ukugeleza okuzenzakalelayo kwe-UART0/1/3/4/5
I-ADC
- Kufika eziteshini ezine ze-ADC
- ukulungiswa kwe-12-bit
- VoltagUbubanzi bokufaka kwe-e phakathi kuka-0V kuya ku-1.8V
- Isekela kufika ku-1MS/ssampisilinganiso sezilimi
I-PWM
- 11 on-chip PWMs asebenza ngokuphazanyiswa
- Support 32-bit time/counter facility
- Inketho ye-IR ku-PWM3/7
Iyunithi yamandla
- Amandla Ahlukene ebhodini
- Okokufaka okukodwa okungu-3.3V
CM1126B-P Block Diagram
RV1126B-P Block Diagram
Ibhodi lokuthuthukisa (Idea1126) Block Diagram
CM1126B-P PCB Dimension
CM1126B-P Pin Definition
| Phina | Isiginali | Incazelo noma imisebenzi | I-GPIO serial | IO Voltage |
| 1 | I-LCDC_D19_3V3 | I2S1_MCLK_M2/CIF_D15_M1 | GPIO2_C7_d | 3.3V |
| 2 | I-LCDC_D20_3V3 | I2S1_SDO_M2/CIF_VS_M1 | I-GPIO2_D0_d | 3.3V |
| 3 | I-LCDC_D21_3V3 | I2S1_SCLK_M2/CIF_CLKO_M1 | I-GPIO2_D1_d | 3.3V |
| 4 | I-LCDC_D22_3V3 | I2S1_LRCK_M2/CIF_CKIN_M1 | I-GPIO2_D2_d | 3.3V |
| 5 | I-LCDC_D23_3V3 | I2S1_SDI_M2/CIF_HS_M1 | I-GPIO2_D3_d | 3.3V |
| 6 | GND | Ground | 0V | |
| 7 | I-GPIO1_D1 | UART1_RX_M1/I2C5_SDA_M2 | I-GPIO1_D1_d | 3.3V(V2) |
| 8 | BT_WAKE | SPI0_CS1n_M0 | GPIO0_A4_u | 3.3V(V2) |
| 9 | I-WIFI_REG_ON | SPI0_MOSI_M0 | I-GPIO0_A6_d | 3.3V(V2) |
| 10 | BT_RST | SPI0_MISO_M0 | I-GPIO0_A7_d | 3.3V(V2) |
| 11 | I-WIFI_WAKE_HOST | SPI0_CLK_M0 | I-GPIO0_B0_d | 3.3V(V2) |
| 12 | BT_WAKE_HOST | SPI0_CS0n_M0 | GPIO0_A5_u | 3.3V(V2) |
| 13 | PWM7_IR_M0_3V3 | I-GPIO0_B1_d | 3.3V | |
| 14 | PWM6_M0_3V3 | TSADC_SHUT_M1 | I-GPIO0_B2_d | 3.3V |
| 15 | UART2_TX_3V3 | Okokulungisa iphutha | GPIO3_A2_u | 3.3V |
| 16 | UART2_RX_3V3 | Okokulungisa iphutha | GPIO3_A3_u | 3.3V |
| 17 | I2S0_MCLK_M0_3V
3 |
I-GPIO3_D2_d | 3.3V | |
| 18 | I2S0_SCLK_TX_M0
_3V3 |
ACODEC_DAC_CLK | I-GPIO3_D0_d | 3.3V |
| 19 | I2S0_SDI3_M0_3V3 | PDM_SDI3_M0 /
ACODEC_ADC_DATA |
I-GPIO3_D7_d | 3.3V |
| 20 | I2S0_SDO0_M0_3V
3 |
ACODEC_DAC_DATAR
/APWM_R_M1/ADSM_LP |
I-GPIO3_D5_d | 3.3V |
| Phina | Isiginali | Incazelo noma imisebenzi | I-GPIO serial | IO Voltage |
| 21 | I2S0_LRCK_TX_M0
_3V3 |
ACODEC_DAC_SYNC
/APWM_L_M1/ADSM_LN |
I-GPIO3_D3_d | 3.3V |
| 22 | PDM_SDI1_3V3 | I2S0_SDO3_SDI1_M0/I2C4SDA | I-GPIO4_A1_d | 3.3V |
| 23 | PDM_CLK1_3V3 | I2S0_SCK_RX_M0 | I-GPIO3_D1_d | 3.3V |
| 24 | PDM_SDI2_3V3 | I2S0_SDO2_SDI2_M0/I2C4SCL | I-GPIO4_A0_d | 3.3V |
| 25 | PDM_SDI0_3V3 | I2S0_SDI0_M0 | I-GPIO3_D6_d | 3.3V |
| 26 | PDM_CLK_3V3 | I2S0_LRCK_RX_M0 | I-GPIO3_D4_d | 3.3V |
| 27 | I2C2_SDA_3V3 | I-PWM5_M0 | GPIO0_C3_d | 3.3V |
| 28 | I2C2_SCL_3V3 | I-PWM4_M0 | GPIO0_C2_d | 3.3V |
| 29 | USB_HOST_DP | 1.8V | ||
| 30 | USB_HOST_DM | 1.8V | ||
| 31 | GND | Ground | 0V | |
| 32 | OTG_DP | Can be used for download | 1.8V | |
| 33 | OTG_DM | Can be used for download | 1.8V | |
| 34 | OTG_DET(V2) | I-OTG VBUS DET IN | 3.3V(V2) | |
| 35 | OTG_ID | 1.8V | ||
| 36 | SPI0_CS1n_M1 | I2S1_MCK_M1/UART4_TX_M2 | I-GPIO1_D5_d | 1.8V |
| 37 | VCC3V3_SYS | 3.3V Okokufaka kwamandla amakhulu | 3.3V | |
| 38 | VCC3V3_SYS | 3.3V Okokufaka kwamandla amakhulu | 3.3V | |
| 39 | I-USB_CTRL_3V3 | GPIO0_C1_d | 3.3V | |
| 40 | SDMMC0_DET | Kufanele isetshenziselwe Ikhadi le-SD | GPIO0_A3_u | 3.3V(V2) |
| 41 | CLKO_32K | Okukhipha iwashi le-RTC | GPIO0_A2_u | 3.3V(V2) |
| 42 | nRESET | Setha kabusha okokufaka kokhiye | 3.3V(V2) | |
| 43 | MIPI_CSI_RX0_CL
KP |
Okokufaka kwe-MIPI CSI0 noma kwe-LVDS0 | 1.8V | |
| 44 | MIPI_CSI_RX0_CL
KN |
Okokufaka kwe-MIPI CSI0 noma kwe-LVDS0 | 1.8V | |
| 45 | MIPI_CSI_RX0_D2
P |
Okokufaka kwe-MIPI CSI0 noma kwe-LVDS0 | 1.8V | |
| 46 | MIPI_CSI_RX0_D2
N |
Okokufaka kwe-MIPI CSI0 noma kwe-LVDS0 | 1.8V | |
| 47 | MIPI_CSI_RX0_D3
P |
Okokufaka kwe-MIPI CSI0 noma kwe-LVDS0 | 1.8V | |
| 48 | MIPI_CSI_RX0_D3
N |
Okokufaka kwe-MIPI CSI0 noma kwe-LVDS0 | 1.8V | |
| 49 | MIPI_CSI_RX0_D1
P |
Okokufaka kwe-MIPI CSI0 noma kwe-LVDS0 | 1.8V | |
| 50 | MIPI_CSI_RX0_D1
N |
Okokufaka kwe-MIPI CSI0 noma kwe-LVDS0 | 1.8V | |
| 51 | MIPI_CSI_RX0_D0
P |
Okokufaka kwe-MIPI CSI0 noma kwe-LVDS0 | 1.8V |
| Phina | Isiginali | Incazelo noma imisebenzi | I-GPIO serial | IO Voltage |
| 52 | MIPI_CSI_RX0_D0
N |
Okokufaka kwe-MIPI CSI0 noma kwe-LVDS0 | 1.8V | |
| 53 | GND | Ground | 0V | |
| 54 | MIPI_CSI_RX1_D3
P |
Okokufaka kwe-MIPI CSI1 noma kwe-LVDS1 | 1.8V | |
| 55 | MIPI_CSI_RX1_D3
N |
Okokufaka kwe-MIPI CSI1 noma kwe-LVDS1 | 1.8V | |
| 56 | MIPI_CSI_RX1_CL
KP |
Okokufaka kwe-MIPI CSI1 noma kwe-LVDS1 | 1.8V | |
| 57 | MIPI_CSI_RX1_CL
KN |
Okokufaka kwe-MIPI CSI1 noma kwe-LVDS1 | 1.8V | |
| 58 | MIPI_CSI_RX1_D2
P |
Okokufaka kwe-MIPI CSI1 noma kwe-LVDS1 | 1.8V | |
| 59 | MIPI_CSI_RX1_D2
N |
Okokufaka kwe-MIPI CSI1 noma kwe-LVDS1 | 1.8V | |
| 60 | MIPI_CSI_RX1_D1
P |
Okokufaka kwe-MIPI CSI1 noma kwe-LVDS1 | 1.8V | |
| 61 | MIPI_CSI_RX1_D1
N |
Okokufaka kwe-MIPI CSI1 noma kwe-LVDS1 | 1.8V | |
| 62 | MIPI_CSI_RX1_D0
P |
Okokufaka kwe-MIPI CSI1 noma kwe-LVDS1 | 1.8V | |
| 63 | MIPI_CSI_RX1_D0
N |
Okokufaka kwe-MIPI CSI1 noma kwe-LVDS1 | 1.8V | |
| 64 | SDMMC0_D3_3V3 | UART3_TX_M1 | GPIO1_A7_u | 3.3V |
| 65 | SDMMC0_D2_3V3 | UART3_RX_M1 | GPIO1_A6_u | 3.3V |
| 66 | SDMMC0_D1_3V3 | UART2_TX_M0 | GPIO1_A5_u | 3.3V |
| 67 | SDMMC0_D0_3V3 | UART2_RX_M0 | GPIO1_A4_u | 3.3V |
| 68 | SDMMC0_CMD_3V
3 |
UART3_CTSn_M1 | GPIO1_B1_u | 3.3V |
| 69 | SDMMC0_CLK_3V3 | UART3_RTSn_M1 | GPIO1_B0_u | 3.3V |
| 70 | GND | Ground | 0V | |
| 71 | I-LED1/CFG_LDO0 | I-Ethernet LINK LED | 3.3V | |
| 72 | I-LED2/CFG_LDO1 | I-Ethernet SPEED LED | 3.3V | |
| 73 | I-MDI0+ | Isignali ye-Ethernet MDI | 1.8V | |
| 74 | I-MDI0- | Isignali ye-Ethernet MDI | 1.8V | |
| 75 | I-MDI1+ | Isignali ye-Ethernet MDI | 1.8V | |
| 76 | I-MDI1- | Isignali ye-Ethernet MDI | 1.8V | |
| 77 | I-MDI2+ | Isignali ye-Ethernet MDI | 1.8V | |
| 78 | I-MDI2- | Isignali ye-Ethernet MDI | 1.8V | |
| 79 | I-MDI3+ | Isignali ye-Ethernet MDI | 1.8V | |
| 80 | I-MDI3- | Isignali ye-Ethernet MDI | 1.8V | |
| 81 | I-I2C1_SCL | UART4_CTSn_M2 | I-GPIO1_D3_u | 1.8V |
| Phina | Isiginali | Incazelo noma imisebenzi | I-GPIO serial | IO Voltage |
| 82 | I2C1_SDA | UART4_RTSn_M2 | I-GPIO1_D2_u | 1.8V |
| 83 | MIPI_CSI_PWDN0 | UART4_RX_M2 | I-GPIO1_D4_d | 1.8V |
| 84 | SPI0_CLK_M1 | I2S1_SDO_M1/UART5_RX_M2 | I-GPIO2_A1_d | 1.8V |
| 85 | SPI0_MOSI_M1 | I2S1_SCK_M1/I2C3_SCL_M2 | I-GPIO1_D6_d | 1.8V |
| 86 | SPI0_CS0n_M1 | I2S1_SDI_M1/UART5_TX_M2 | I-GPIO2_A0_d | 1.8V |
| 87 | SPI0_MISO_M1 | I2S1_LRCK_M1/I2C3_SDA_M2 | I-GPIO1_D7_d | 1.8V |
| 88 | MIPI_CSI_CLK1 | UART5_RTSn_M2 | I-GPIO2_A2_d | 1.8V |
| 89 | MIPI_CSI_CLK0 | UART5_CTSn_M2 | I-GPIO2_A3_d | 1.8V |
| 90 | GND | Ground | 0V | |
| 91 | I-LCDC_D0_3V3 | UART4_RTSn_M1/CIF_D0_M1 | I-GPIO2_A4_d | 3.3V |
| 92 | I-LCDC_D1_3V3 | UART4_CTSn_M1/CIF_D1_M1 | I-GPIO2_A5_d | 3.3V |
| 93 | I-LCDC_D2_3V3 | UART4_TX_M1/CIF_D2_M1 | I-GPIO2_A6_d | 3.3V |
| 94 | I-LCDC_D3_3V3 | UART4_RX_M1/I2S2_SDO_M1 | I-GPIO2_A7_d | 3.3V |
| 95 | I-LCDC_D4_3V3 | UART5_TX_M1/I2S2_SDI_M1 | I-GPIO2_B0_d | 3.3V |
| 96 | I-LCDC_D5_3V3 | UART5_RX_M1/I2S2_SCK_M1 | I-GPIO2_B1_d | 3.3V |
| 97 | I-LCDC_D6_3V3 | UART5_RTSn_M1/I2S2_LRCK_
M1 |
I-GPIO2_B2_d | 3.3V |
| 98 | I-LCDC_D7_3V3 | UART5_CTSn_M1/I2S2_MCLK_
M1/CIF_D3_M1 |
I-GPIO2_B3_d | 3.3V |
| 99 | CAN_RX_3V3 | UART3_TX_M2/I2C4_SCL_M0 | GPIO3_A0_u | 3.3V |
| 100 | CAN_TX_3V3 | UART3_RX_M2/I2C4_SDA_M0 | GPIO3_A1_u | 3.3V |
| 101 | I-LCDC_CLK_3V3 | UART3_CTSn_M2/SPI1_MISO_
M2/PWM8_M1 |
I-GPIO2_D7_d | 3.3V |
| 102 | I-LCDC_VSYNC_3V3 | UART3_RTSn_M2/SPI1_MOSI | I-GPIO2_D6_d | 3.3V |
| 103 | MIPI_DSI_D2P | 1.8V | ||
| 104 | MIPI_DSI_D2N | 1.8V | ||
| 105 | MIPI_DSI_D1P | 1.8V | ||
| 106 | MIPI_DSI_D1N | 1.8V | ||
| 107 | MIPI_DSI_D0P | 1.8V | ||
| 108 | MIPI_DSI_D0N | 1.8V | ||
| 109 | MIPI_DSI_D3P | 1.8V | ||
| 110 | MIPI_DSI_D3N | 1.8V | ||
| 111 | MIPI_DSI_CLKP | 1.8V | ||
| 112 | MIPI_DSI_CLKN | 1.8V | ||
| 113 | ADCIN3 | Okokufaka kwe-ADC | 1.8V | |
| 114 | ADCIN2 | Okokufaka kwe-ADC | 1.8V | |
| 115 | ADCIN1 | Okokufaka kwe-ADC | 1.8V | |
| 116 | ADKEY_IN0 | Imodi yokutakula isethiwe(10K PU) | 1.8V | |
| 117 | GND | Ground | 0V | |
| 118 | I-SDIO_CLK | I-GPIO1_B2_d | 3.3V(V2) | |
| 119 | I-SDIO_CMD | GPIO1_B3_u | 3.3V(V2) |
| Phina | Isiginali | Incazelo noma imisebenzi | I-GPIO serial | IO Voltage |
| 120 | I-SDIO_D0 | GPIO1_B4_u | 3.3V(V2) | |
| 121 | I-SDIO_D1 | GPIO1_B5_u | 3.3V(V2) | |
| 122 | I-SDIO_D2 | GPIO1_B6_u | 3.3V(V2) | |
| 123 | I-SDIO_D3 | GPIO1_B7_u | 3.3V(V2) | |
| 124 | UART0_RX | GPIO1_C2_u | 3.3V(V2) | |
| 125 | UART0_TX | GPIO1_C3_u | 3.3V(V2) | |
| 126 | UART0_CTSN | GPIO1_C1_u | 3.3V(V2) | |
| 127 | UART0_RTSN | GPIO1_C0_u | 3.3V(V2) | |
| 128 | PCM_TX | I2S2_SDO_M0/SPI1_MOSI_M1 | GPIO1_C4_d | 3.3V(V2) |
| 129 | PCM_SYNC | I2S2_LRCK_M0/SPI1_CSn0_M
1/UART1_CTSn_M1 |
GPIO1_C7_d | 3.3V(V2) |
| 130 | PCM_CLK | I2S2_SCLK_M0/SPI1_CLK_M1/
UART1_RTSn_M1 |
GPIO1_C6_d | 3.3V(V2) |
| 131 | PCM_RX | I2S2_SDI_M0/SPI1_MISO_M1 | GPIO1_C5_d | 3.3V(V2) |
| 132 | I-LCDC_D15_3V3 | CIF_D11_M1 | GPIO2_C3_d | 3.3V |
| 133 | I-LCDC_D14_3V3 | CIF_D10_M1 | GPIO2_C2_d | 3.3V |
| 134 | I-LCDC_D13_3V3 | CIF_D9_M1 | GPIO2_C1_d | 3.3V |
| 135 | I-LCDC_D12_3V3 | CIF_D8_M1 | GPIO2_C0_d | 3.3V |
| 136 | I-LCDC_DEN_3V3 | I2C3_SCL_M1/SPI1_CS0n_M2 | I-GPIO2_D4_d | 3.3V |
| 137 | I-LCDC_D10_3V3 | CIF_D6_M1 | I-GPIO2_B6_d | 3.3V |
| 138 | I-LCDC_D9_3V3 | CIF_D5_M1 | I-GPIO2_B5_d | 3.3V |
| 139 | I-LCDC_D8_3V3 | CIF_D4_M1 | I-GPIO2_B4_d | 3.3V |
| 140 | I-LCDC_D11_3V3 | CIF_D7_M1 | I-GPIO2_B7_d | 3.3V |
| 141 | I-LCDC_HSYNC_3V3 | I2C3_SDA_M1/SPI1_CLK_M2 | I-GPIO2_D5_d | 3.3V |
| 142 | I-LCDC_D16_3V3 | CIF_D12_M1 | GPIO2_C4_d | 3.3V |
| 143 | I-LCDC_D17_3V3 | CIF_D13_M1 | GPIO2_C5_d | 3.3V |
| 144 | I-LCDC_D18_3V3 | CIF_D14_M1 | GPIO2_C6_d | 3.3V |
| Qaphela:
1. Inani eliphakeme kakhulu lama-GPIOtage ingu-1.8V, kodwa amanye amaphini abhalwe ukuthi 3.3V. 2. GPIO voltage change to 3.3V for marked (V2). |
||||
Ikhithi Yokuthuthukisa (Idea1126)
Hardware Design Guide
I-Peripheral Circuit Reference
Main Circuit Amandla
Debug Circuit
I-USB OTG Interface Circuit
I-PCB Footprint
Izici Zogesi Zomkhiqizo
Ukuhlakazeka kanye Nezinga Lokushisa
| Uphawu | Ipharamitha | Okuncane | Thayipha | Ubukhulu | Iyunithi |
| VCC3V3_SYS | Isistimu ye-IO
Voltage |
3.3-5% | 3.3 | 3.3+5% | V |
| Iyss_in | Okokufaka kwe-VCC3V3_SYS kwamanje | 850 | mA | ||
| Ta | Izinga Lokushisa Lokusebenza | -20 | 70 | °C | |
| Tstg | Izinga Lokushisa Lesitoreji | -40 | 85 | °C |
Ukuthembeka kokuhlolwa
| Ukuhlolwa Kwezinga Lokushisa Okuphezulu | ||
| Okuqukethwe | Operating 8h in high temperatures | 55°C±2°C |
| Umphumela | I-TBD |
| Operating Life Test | ||
| Okuqukethwe | Operating in the room | 120h |
| Umphumela | I-TBD |
Iwaranti Enomkhawuko
Boardcon warrants this product to be free of defects in material and workmanship for one year from the date of purchase. During this warranty period, Boardcon will repair or replace the defective unit by the following process: A copy of the original invoice must be included when returning the defective unit to Boardcon. This limited warranty does not cover damages resulting from lightning or other power surges, misuse, abuse, abnormal conditions of operation, or attempts to alter or modify the function of the product. This warranty is limited to the repair or replacement of the defective unit. In no event shall Boardcon be liable or responsible for any loss or damages, including but not limited to any lost profits, incidental or consequential damages, loss of business, or anticipatory profits arising from the use or inability to use this product. Repairs made after the expiration of the warranty period are subject to a repair charge and the cost of return shipping. Please contact Boardcon to arrange for any repair service and to obtain repair charge information.
Imibuzo Evame Ukubuzwa
Q: How do I upgrade the DDR memory on CM1126B-P?
A: The CM1126B-P supports up to 4GB LPDDR4 memory. To upgrade, ensure compatibility with the specifications and follow recommended procedures.
Q: What is the power supply requirement for CM1126B-P?
A: The power requirement for CM1126B-P is DC 3.3V. Ensure to provide a stable power supply within this range for optimal performance.
Q: Can I expand the storage capacity of eMMC on CM1126B-P?
A: Yes, the eMMC storage on CM1126B-P can be expanded up to 256GB. Ensure compatibility with supported storage devices before upgrading.
Amadokhumenti / Izinsiza
 |
Boardcon Embedded CM1126B-P System on Module [pdf] Imaniwali yosebenzisayo V2.20250422, CM1126B-P System on Module, CM1126B-P, System on Module, Module |