Isingeniso
I-Wampler Catacombs is a programmable, all-in-one delay and reverb pedal designed to provide a wide range of time-based effects for musicians. This manual provides essential information for setting up, operating, maintaining, and troubleshooting your Catacombs pedal.
Umkhiqizo Uphelileview
The Catacombs pedal integrates 11 popular delay and reverb sounds into a single, intuitive unit. It features studio-quality 48 kHz sampling rate with 24-bit audio conversion, 8 onboard preset locations, and MIDI compatibility for up to 128 total presets.
Umfanekiso 1: Ngaphambili view kwe Wampler Catacombs pedal, showing controls for delay and reverb effects, input/output jacks, and footswitches.
Umfanekiso 2: I-engeli view kwe Wampler Catacombs pedal, highlighting its compact design and various control knobs.
Setha
Izidingo zamandla
I-Wampler Catacombs pedal requires a standard 9V DC power supply (not included) with a center-negative barrel connector. Ensure the power supply provides sufficient current for optimal performance.
Connecting Your Pedal
- Connect your instrument (e.g., guitar) to the MONO IN or I-STEREO IN jack on the right side of the pedal using a standard 1/4-inch instrument cable.
- Xhuma i- MONO OUT or I-STEREO OUT jack on the left side of the pedal to your amplifier or next effect pedal.
- Connect the 9V DC power supply to the 9V DC ujeke wokufaka.
- For MIDI control, connect a MIDI cable to the I-MIDI okokufaka.
Imiyalelo yokusebenza
Izilawuliview
- Delay Type Knob: Selects between various delay types including Tape, SPC, FTE, BBD, ANLG, and DIGI.
- Reverb Type Knob: Selects between reverb types such as SHMR (Shimmer), PLT (Plate), SPR (Spring), ROOM, and HALL.
- Time/Shimmer Knob: Adjusts the delay time or shimmer intensity depending on the selected effect.
- Feedback/Decay Knob: Controls the number of delay repeats or the reverb decay time.
- Mod Rate Knob: Adjusts the modulation rate for effects with modulation.
- Delay Tone Knob: Shapes the tone of the delay repeats.
- Reverb Tone Knob: Shapes the tone of the reverb effect.
- Bypass/ALT Footswitch: Toggles the effect on/off. Hold to access alternate functions (ALT mode).
- Preset/Save Footswitch: Cycles through presets. Hold to save current settings to a preset location.
- Tap Tempo Footswitch: Taps in the desired delay tempo.
Saving and Recalling Presets
The Catacombs pedal allows for 8 onboard preset locations. To save a preset, adjust the knobs to your desired sound, then press and hold the Preset/Save footswitch until the indicator lights confirm the save. To recall a preset, short press the Preset/Save footswitch to cycle through the saved locations.
Alternate Functions (ALT Mode)
Some knobs have alternate functions accessible by holding the Bypass/ALT footswitch. When in ALT mode, the indicator light will change (e.g., from blue to red as noted in some user feedback), allowing you to adjust secondary parameters. Release the footswitch to return to normal operation.
Isondlo
To ensure the longevity and optimal performance of your Wampler Catacombs pedal, follow these maintenance guidelines:
- Keep the pedal clean by wiping it with a soft, dry cloth. Avoid abrasive cleaners or solvents.
- Store the pedal in a cool, dry place away from direct sunlight and extreme temperatures.
- Disconnect power when not in use for extended periods.
- Regularly check all cable connections for secure fit.
Ukuxazulula inkinga
| Inkinga | Imbangela Engenzeka | Isixazululo |
|---|---|---|
| Akukho msindo uma kuqhutshwa i-pedal. | Incorrect power supply, faulty cables, incorrect input/output connections. | Verify power supply is 9V DC center-negative. Check all instrument cables. Ensure input is connected to IN and output to OUT. |
| Effect is too subtle or too extreme. | Knobs are set incorrectly, or in ALT mode unintentionally. | Adjust the relevant control knobs (Time, Feedback, Tone). Check if the pedal is in ALT mode and adjust accordingly. |
| Cannot save or recall presets. | Incorrect footswitch operation. | Qinisekisa ukuthi ubambe Preset/Save footswitch long enough to save. For recalling, use short presses. |
| Noise or hum. | Ground loop, faulty power supply, interference. | Use an isolated power supply. Try different cables. Ensure proper grounding of all equipment. |
Imininingwane
- Imodeli: CATACOMBS
- Ubukhulu: 7.25 x 5.7 x 3.75 amayintshi
- Isisindo Sento: 1.39 amakhilogremu
- Umthombo wamandla: Corded Electric (9V DC, center-negative, power supply not included)
- Ifomethi Yesiginali: I-Analog
- Audio Output Effects: Libazisa, Isaga
- SampLing Ling: 48 kHz
- Audio Bit Depth: 24-bit
- Ukuhlelwa kwangaphambili: 8 onboard, 128 via MIDI
- Manufacture Location: Designed and Built in the USA
Iwaranti kanye Nokusekela
Wampler Pedals products are designed and built to high standards. For warranty information and technical support, please refer to the official Wample Pedals webisayithi noma uxhumane nesevisi yabo yamakhasimende ngokuqondile. Gcina ubufakazi bakho bokuthenga ngezimangalo zewaranti.
Ukuze uthole olunye usizo, vakashela i- Wampler Store on Amazon.
