AT-START-F435 Incwadi Yomsebenzisi
Ukuqalisa nge-AT32F435ZMT7
Isingeniso
I-AT-START-F435 yakhelwe ukukusiza ukuthi uhlole ukusebenza okuphezulu kwe-32-bit microcontroller AT32F435 eshumeka umgogodla we-ARM Cortex® -M4 nge-FPU, futhi usheshise ukuthuthukiswa kohlelo lokusebenza. I-AT-START-F435 ibhodi lokuhlola elisekelwe ku-AT32F435ZMT7 microcontroller. Idivayisi iqukethe ama-peripheral afana nama-LED, izinkinobho, izixhumi ezimbili ze-USB micro-B, isixhumi sohlobo A, izixhumanisi zokunweba ze-Arduino™ Uno R3 kanye nememori ye-SPI Flash engu-16 MB (inwetshwe nge-QSPI1).
Leli bhodi lokuhlola lishumeka i-AT-Link-EZ ukuze ilungise iphutha/ihlelwe ngaphandle kwesidingo samanye amathuluzi okuthuthukisa.
Kuphelileview
1.1 Izici
I-AT-START-F435 inezici ezilandelayo:
- I-AT-START-F435 inesilawuli esincane esisebhodini esingu-AT32F435ZMT7 esishumeka i-ARM Cortex ®
– I-M4F 32-bit core ene-FPU, 4032 KB Flash memory kanye no-384 KB SRAM, kumaphakheji e-LQFP144. - Isixhumi esibonakalayo se-AT-Link esisebhodini:
− I-AT-Link-EZ engaphakathi ingasetshenziselwa ukuhlela nokulungisa iphutha (i-AT-Link-EZ inguqulo eyenziwe lula ye-AT-Link, ngaphandle kokusekelwa kwemodi engaxhunyiwe ku-inthanethi)
− Uma i-AT-Link-EZ iye yahlakazwa ebhodini ngokuyigoba eduze kwelunga, lesi sixhumanisi singaxhunywa ku-AT-Link ezimele yokuhlela nokulungisa iphutha. - Ebhodini 20-pin ARM standard JTAG interface (ingaxhunywa ku-JTAG noma isixhumi se-SWD sokuhlela nokulungisa iphutha)
- 16 MB SPI (EN25QH128A) isetshenziswa njengememori yeFlash enwetshiwe
- Izindlela ezihlukene zokuhlinzeka ngogesi:
− Ibhasi le-USB le-AT-Link-EZ
− OTG1 noma OTG2 ibhasi (VBUS1 noma VBUS2) ye-AT-START-F435
− Ugesi wangaphandle oyi-5 V (E5V)
− Ugesi wangaphandle ongu-3.3 V - 4 x Izinkomba ze-LED:
− I-LED1 (ebomvu) ikhombisa ugesi ongu-3.3 V
− 3 x USER LEDs, LED2 (red),LED3 (yellow) kanye neLED4 (green), akhombisa isimo sokusebenza - Inkinobho yomsebenzisi nenkinobho yokusetha kabusha
- 8 MHz HEXT ikristalu
- 32.768 kHz LEXT crystal
- Ebhodini uhlobo lwe-USB yohlobo-A nezixhumi ezincane-B ukuze kuboniswe umsebenzi we-OTG1
- I-OTG2 inesixhumi esincane se-B (Uma umsebenzisi efuna ukusebenzisa imodi eyinhloko ye-OTG2, ikhebula le-adaptha liyadingeka)
- Izixhumanisi zesandiso ezinothile ziyatholakala ukuze kwenziwe i-prototyping ngokushesha
− Isixhumanisi esibonakalayo se-ArduinoTM Uno R3
− LQFP144 I/O isixhumi esibonakalayo esinwetshiwe
1.2 Incazelo yamagama
- I-Jumper JPx IVULIWE
I-Jumper ifakiwe. - I-Jumper JPx IVALIWE
I-Jump ayifakiwe. - I-Resistor Rx ON / i-PRx resistor yenethiwekhi IVULIWE
Ifushane nge-solder, i-resistor engu-0Ω noma isixhasi senethiwekhi. - I-Resistor Rx IVALIWE / i-PRx resistor yenethiwekhi
Vula.
Ukuqala okusheshayo
2.1 Qala
Lungiselela ibhodi le-AT-START-F435 ngokulandelana okulandelayo:
- Hlola indawo ye-Jumper ebhodini:
I-JP1 ixhunywe ku-GND noma OFF (BOOT0 = 0, futhi i-BOOT0 ine-resistor yokudonsela phansi ku-AT32F435ZMT7);
I-JP2 ixhumeke ku-GND (BOOT1=0)
I-JP4 ixhunywe ku-USART1 - Xhuma i-AT_Link_EZ ku-PC ngentambo ye-USB (Uhlobo A kuya ku-micro-B), bese unikeza amandla ebhodini lokuhlola ngesixhumi se-USB CN6. I-LED1 (ebomvu) ihlezi ivuliwe, futhi amanye ama-LED amathathu (i-LED2 ukuya ku-LED4) aqala ukucwayiza ngokulandelana.
- Ngemva kokucindezela inkinobho yomsebenzisi (B2), imvamisa ecwayizayo yama-LED amathathu iyashintshwa.
2.2 Amathuluzi okuthuthukisa i-AT-START-F435
- I-ARM ® Keil ® : MDK-ARM™
- I-IAR™: EWARM
Izingxenyekazi zekhompuyutha nesakhiwo
Ibhodi le-AT-START-F435 lakhiwe ngokuzungeza isilawuli esincane se-AT32F435ZMT7 kuphakheji ye-LQFP144.
Umfanekiso 1 ubonisa ukuxhumana phakathi kwe-AT-Link-EZ, AT32F435ZMT7 kanye namapheripherals awo (izinkinobho, ama-LED, i-USB OTG, i-SPI nezixhumi zesandiso)
Umfanekiso 2 kanye noMfanekiso 3 ubonisa izindawo zabo ngokulandelana kwazo ebhodini le-AT-Link-EZ kanye ne-AT-START-F435.
 |
 |
3.1 Ukukhetha kokuphakelwa kukagesi
I-AT-START-F435 ayikwazi ukuhlinzekwa nge-5 V kuphela ngentambo ye-USB (okungaba ngesixhumi se-USB CN6 ku-AT-Link-EZ noma isixhumi se-USB CN2/CN3 ku-AT-START-F435), kodwa futhi ihlinzekwe ngesixhumi se-USB. ukunikezwa kwamandla kwangaphandle okungu-5 V (E5V). Bese kuthi amandla angu-5 V ahlinzeke nge-3.3 V yesilawuli esincane namapheripheral ayo kusetshenziswa i-onboard 3.3 V vol.tagi-e regulator (U2).
Iphinikhodi engu-5 V ye-J4 noma i-J7 nayo ingasetshenziswa njengamandla okufaka, ngakho-ke ibhodi le-AT-START-F435 linganikezwa ngeyunithi yamandla engu-5 V. Iphinikhodi engu-3.3 V ye-J4, noma i-VDD ye-J1 ne-J2 ingasetshenziswa njengokufaka okungu-3.3 V ngokuqondile, ukuze ibhodi le-AT-STARTF435 nalo linikezwe 3.3 V iyunithi yamandla.
Qaphela: Ugesi ongu-5 V kufanele unikezwe ngesixhumi se-USB (CN6) ku-AT-Link-EZ. Noma iyiphi enye indlela ayikwazi ukunika amandla i-AT-Link-EZ.
Uma elinye ibhodi lixhunywe ku-J4, i-5 V kanye ne-3.3 V ingasetshenziswa amandla okukhipha, iphinikhodi ye-J7's 5V njengamandla okukhiphayo angu-5 V, iphinikhodi ye-VDD ye-J1 ne-J2 njengamandla okukhiphayo angu-3.3 V.
3.2 I-IDD
Uma i-JP3 IVALIWE (i-IDD yophawu) kanye ne-R17 OFF, i-ammeter ingaxhunywa ukuze kukalwe ukusetshenziswa kwamandla kwe-AT32F435ZMT7.
- I-JP3 IVALIWE, i-R17 VALIWE:
I-AT32F435ZMT7 inikwe amandla (Ukusetha okuzenzakalelayo kanye nepulaki ye-JP3 ayigxunyekwanga ngaphambi kokusuka efekthri) - I-JP3 IVULIWE, IVALIWE R17:
I-AT32F435ZMT7 inikwe amandla - JP3 OFF, R17 OFF:
I-ammeter kufanele ixhunywe. Uma ingekho i-ammeter etholakalayo, i-AT32F435ZMT7 ayikwazi ukunikwa amandla.
3.3 Ukuhlela nokulungisa iphutha: kushumekwe i-AT-Link-EZ
Ibhodi lokuhlola lihlanganisa i-Artery AT-Link-EZ ukuze abasebenzisi bahlele/balungise iphutha le-AT32F435ZMT7 ebhodini le-AT-START-F435. I-AT-Link-EZ isekela imodi yesixhumi esibonakalayo se-SWD, ukulungisa iphutha le-SWO, kanye nesethi yezimbobo ezibonakalayo ze-COM (VCP) ukuze ixhume ku-USART1_TX/USART1_RX (PA9/PA10) ye-AT32F435ZMT7.
Sicela ubheke i-AT-Link User Manual ukuze uthole imininingwane ephelele ku-AT-Link-EZ.
I-AT-Link-EZ esebhodini ingahlakazwa noma ihlukaniswe ku-AT-START-F435. Kulokhu, i-AT-START-F435 isengaxhunywa ku-interface ye-CN7 (engafakwanga ngaphambi kokusuka efekthri) ye-AT-Link-EZ ngokusebenzisa isixhumi esibonakalayo se-CN4 (esingafakwanga ngaphambi kokusuka efekthri), noma ku-AT-Link, ukuze ukuze uqhubeke nokuhlela nokulungisa iphutha i-AT32F435ZMT7.
3.4 Ukukhetha imodi yokuqalisa
Ekuqaleni, izindlela ezintathu zokuqalisa ezihlukene ziyatholakala ukuze zikhethwe ngokucushwa kwephini.
Ithebula 1. Izilungiselelo ze-jumper yokukhetha imodi yokuqalisa
| I-Jumper | Ukucushwa kwephinikhodi | Imodi yokuqalisa | |
| IBHODI1 | I-BOOTO | ||
| JP1 kuya ku-GND noma VALE I-JP2 uyazikhethela noma VALIWE |
X | 0 | Qalisa kumemori ye-Flash yangaphakathi (ukusetha okuzenzakalelayo kwasefekthri) |
| JP1 kuya ku-VDD JP2 kuya ku-GND |
0 | 1 | Qalisa kusuka kumemori yesistimu |
| JP1 kuya ku-VDD JP2 kuya ku-VDD |
1 | 1 | Qalisa ku-SRAM yangaphakathi |
3.5 Umthombo wewashi wangaphandle
3.5.1 Umthombo wewashi le-HEXT
Kunezindlela ezintathu zokumisa imithombo yangaphandle yewashi elinesivinini esiphezulu ngehadiwe:
- Ikristalu esebhodini (Isilungiselelo esizenzakalelayo sasefekthri)
Ikristalu elisebhodini engu-8 MHz isetshenziswa njengomthombo wewashi le-HSE. I-hardware kufanele imiswe: i-R1 ne-R3 ON, i-R2 ne-R4 OFF. - I-oscillator yangaphandle esuka ku-PH0
I-oscillator yangaphandle ijovwa kusukela kuphinikhodi_23 ye-J2. Ihardware kumele imiswe: R2 ON, R1 and R3 OFF. Ukuze usebenzise i-PH1 njenge-GPIO, i-R4 ON ingaxhunywa kuphinikhodi_24 ye-J2. - HSE engasetshenziswanga
I-PH0 ne-PH1 isetshenziswa njengama-GPIO. I-hardware kufanele imiswe: i-R14 ne-R16 ON, i-R1 ne-R15 OFF.
3.5.2 Umthombo wewashi LEXT
Kunezindlela ezintathu zokumisa imithombo yangaphandle yewashi elinesivinini esiphansi ngehadiwe:
- Ikristalu esebhodini (Isilungiselelo esizenzakalelayo sasefekthri)
Ikristalu elisebhodini engu-32.768 kHz isetshenziswa njengomthombo wewashi le-LEXT. I-hardware kufanele imiswe: i-R5 ne-R6 ON, i-R7 ne-R8 OFF - I-oscillator yangaphandle evela ku-PC14
I-oscillator yangaphandle ijovwa kuphini_3 ye-J2. I-hardware kufanele imiswe: i-R7 ne-R8 ON, i-R5 ne-R6 OFF. - LEXT engasetshenzisiwe
I-PC14 ne-PC15 isetshenziswa njengama-GPIO. I-hardware kufanele imiswe: i-R7 ne-R8 ON, i-R5 ne-R6 OFF.
Ama-LED angama-3.6
- Amandla e-LED1
I-LED ebomvu ikhombisa ukuthi i-AT-START-F435 inikwa amandla yi-3.3 V. - Umsebenzisi we-LED2
I-LED ebomvu ixhunywe kuphinikhodi ye-PD13 ye-AT32F435ZMT7. - Umsebenzisi we-LED3
I-LED ephuzi ixhunywe kuphinikhodi ye-PD14 ye-AT32F435ZMT7. - Umsebenzisi we-LED4
I-LED eluhlaza ixhunywe kuphinikhodi ye-PD15 ye-AT32F435ZMT7.
3.7 Izinkinobho
- Setha kabusha i-B1: Inkinobho yokusetha kabusha
Ixhumeke ku-NRST ukuze usethe kabusha isilawuli esincane se-AT32F435ZMT7. - Umsebenzisi B2: Inkinobho yomsebenzisi
Ixhunywe ku-PA0 ye-AT32F435ZMT7 ukuze isebenze njengenkinobho yokuvusa (i-R19 ON ne-R21 OFF), noma ku-PC13 ukuze isebenze njenge-TAMPInkinobho ye-ER-RTC (ISIVALIWE ngo-R19 no-R21 IVULIWE)
3.8 Ukucushwa kwe-OTGFS
Ibhodi le-AT-START-F435 lisekela i-OTGFS1 kanye ne-OTGFS2 umsingathi wesivinini esigcwele/isivinini esiphansi noma imodi yedivayisi enesivinini esigcwele ngesixhumi se-USB micro-B (CN2 noma CN3). Kumodi yedivayisi, i-AT32F435ZMT7 ingaxhunywa ngokuqondile kumsingathi nge-USB micro-B, futhi i-VBUS1 noma i-VBUS2 ingasetshenziswa njengokufaka okungu-5 V kwebhodi le-AT- START-F435. Kumodi yokusingatha, intambo yangaphandle ye-USB OTG iyadingeka ukuze uxhumeke kudivayisi yangaphandle. Idivayisi inikwa amandla nge-USB micro-B interface, eyenziwa yi-PH3 ne-PB10 elawula iswishi ye-SI2301.
Ibhodi le-AT-START-F435 linesixhumi esibonakalayo esinwetshiwe sohlobo lwe-USB (CN1). Lesi isixhumi esibonakalayo somsingathi we-OTGFS1 sokuxhuma kudiski ye-U namanye amadivaysi, ngaphandle kwesidingo sentambo ye-USB OTG. Isixhumi esibonakalayo sohlobo A lwe-USB asinakho isilawuli sokushintshwa kwamandla.
Uma i-PA9 noma i-PA10 ye-AT32F435ZMT7 isetshenziswa njenge-OTGFS1_VBUS noma i-OTGFS1_ID, i-jumper ye-JP4 kufanele ikhethe i-OTG1. Kulokhu, i-PA9 noma i-PA10 ixhumeke kusixhumi esibonakalayo se-USB micro-B CN2, kodwa inqanyuliwe kusixhumi esibonakalayo se-AT-Link (CN4).
3.9 QSPI1 ihlanganisa inkumbulo yeFlash
I-SPI esebhodini (EN25QH128A), exhuma ku-AT32F435ZMT7 ngesixhumi esibonakalayo se-QSPI1, isetshenziswa njengememori ye-Flash enwetshiwe.
Isixhumi esibonakalayo se-QSPI1 sixhunywe kumemori ye-Flash nge-PF6~10 kanye ne-PG6. Uma lawa ma-GPIO esetshenziselwa ezinye izinjongo, kutuswa ukuthi uvale i-RP2, i-R21 ne-R22 kusengaphambili.
3.10 0Ω resistors
Ithebula 2. 0ΩIzilungiselelo zesivikeli
| Abaphikisi | Izwe(1) | Incazelo |
| I-R17 (isilinganiso sokusetshenziswa kwamandla kwe-MCU) | ON | Uma i-JP3 IVALIWE, i-3.3V ixhunywe kumandla we-microcontroller ukuze inikeze isilawuli esincane. |
|
VALIWE |
Uma i-JP3 IVALIWE, i-3.3V ingaxhunywa ku-ammeter ukuze kukalwe ukusetshenziswa kwamandla kwesilawuli esincane. (I-microcontroller ayikwazi ukunikwa amandla ngaphandle kwe-ammeter) | |
| I-R9 (VBAT) | ON | I-VBAT ixhunywe ku-VDD |
| VALIWE | I-VBAT ihlinzekwa yi-pin_6 (VBAT) ye-J2. | |
| R1, R2, R3, R4 (HEXT) | VULA, VULA, VULA, VALIWA | Umthombo wewashi le-HEXT uvela ku-crystal ebhodini Y1 |
| VALIWE, VULA, VILA, VALIWA | Umthombo wewashi le-HEXT: i-oscillator yangaphandle esuka ku-PH0, PH1 ayisetshenziswa. | |
| VALIWE, VULA, VULA, VULA | Umthombo wewashi le-HEXT: i-oscillator yangaphandle evela ku-PH0, i-PH1 isetshenziswa njenge-GPIO; noma PH0, PH1 asetshenziswa njengama-GPIO. | |
| R5, R6, R7, R8 (LEXT) | VULA, VULA, VALIWA, VALIWA | Umthombo wewashi le-LEXT uvela ku-crystal X1 esebhodini |
| VALIWE, VULA, VULA, VULA | Umthombo wewashi le-LEXT: i-oscillator yangaphandle evela ku-PC14; noma i-PC14, i-PC15 isetshenziswa njengama-GPIO. | |
| I-R19, R21 (Inkinobho yomsebenzisi B2) | KHANYISA CISHA | Inkinobho yomsebenzisi ethi B2 ixhunywe ku-PA0. |
| VALIWE, VULIWE | Inkinobho yomsebenzisi ethi B2 ixhunywe ku-PC13. | |
| I-R54, R55 (PA11, PA12) | VALIWE, VALIWE | Njengoba i-OTGFS1, i-PA11 ne-PA12 zingaxhumekile ku-pin_31 kanye ne-pin_32 ye-J1. |
| VULIWE, VULIWE | Uma i-PA11 ne-PA12 zingasetshenziswa njenge-OTGFS1, zixhunywe ku-pin_31 kanye ne-pin_32 ye-J1. | |
| I-R42, R53 (PB14, PB15) | VALIWE, VALIWE | Njengoba i-OTGFS2, i-PB14 ne-PB15 zingaxhumekile ku-pin_3 kanye ne-pin_4 ye-J1. |
| VULIWE, VULIWE | Uma i-PB14 ne-PB15 ingasetshenziswa njenge-OTGFS2, ixhunywe ku-pin_3 kanye ne-pin_4 ye-J1. | |
| I-R56, R57, R58, R59 (ArduinoTM A4, A5) | VALIWE, VULA, VALIWE, ON | I-ArduinoTM A4 ne-A5 axhumeke ku-ADC123_IN11 kanye ne-ADC123_IN10. |
| VULA, VULA, VULA, VALIWA | I-ArduinoTM A4 ne-A5 zixhunywe ku-I2C1_SDA I2C1_SCL. | |
| I-R60, i-R61 (ArduinoTM D10) | VALIWE, ON | I-ArduinoTM I-D10 ixhunywe ku-SPI1_CS. |
| KHANYISA CISHA | I-ArduinoTM D10 ixhunywe ku-PVM (TMR4_CH1). |
3.11 Izixhumanisi ezinwetshiwe
3.11.1 Isixhumanisi esibonakalayo se-Arduino™Uno R3
Ipulaki yesifazane i-J3~J6 nepulaki yesilisa i-J7 isekela isixhumi se-Arduino™ Uno R3. Iningi lamabhodi amantombazane akhelwe ku-Arduino™Uno R3 asebenza ebhodini le-AT-START-F435.
Qaphela: Ama-I/O e-AT32F435ZMT7 angu-3.3 V-ahambisana ne-ArduinoTM Uno R3, kodwa hhayi i-5 V.
Ithebula 3. Incazelo yephinikhodi yesandiso se-Arduino™Uno R3
| Isixhumi | Phina inombolo | I-Arduino Phina igama | I-AT32F435 Phina igama | Incazelo |
|
J4 (Ukunikezwa kwamandla kagesi) |
1 | NC | - | - |
| 2 | IOREF | - | 3.3 V inkomba | |
| 3 | SETHA KABUSHA | I-NRST | Ukusetha kabusha kwangaphandle | |
| 4 | 3.3V | - | 3.3 V okokufaka/okuphumayo | |
| 5 | 5V | - | 5 V okokufaka/okuphumayo | |
| 6 | GND | - | Ground | |
| 7 | GND | - | Ground | |
| 8 | - | - | - | |
| I-J6 (Okufakwayo kwe-Analog) | 1 | A0 | PA0 | I-ADC123_IN0 |
| 2 | A1 | PA1 | I-ADC123_IN1 | |
| 3 | A2 | PA4 | I-ADC12_IN4 | |
| 4 | A3 | PB0 | I-ADC12_IN8 | |
| 5 | A4 | I-PC1 noma i-PB9(1) | I-ADC123_IN11 noma i-I2C1_SDA | |
| 6 | A5 | I-PC0 noma i-PB8(1) | I-ADC123_IN10 noma i-I2C1_SCL | |
| I-J5 (Logic okokufaka/okuphumayo ibhayithi ephansi) | 1 | D0 | PA3 | UART2_RX |
| 2 | D1 | PA2 | UART2_TX | |
| 3 | D2 | PA10 | - | |
| 4 | D3 | PB3 | TMR2_CH2 | |
| 5 | D4 | PB5 | - | |
| 6 | D5 | PB4 | TMR3_CH1 | |
| 7 | D6 | PB10 | TMR2_CH3 | |
| 8 | D7 | I-PA8(2) | - | |
| I-J3 (I-Logic input/output high byte) | 1 | D8 | PA9 | - |
| 2 | D9 | I-PC7 | TMR3_CH2 | |
| 3 | D10 | I-PA15 noma i-PB6(1) | I-SPI1_CS noma i-TMR4_CH1 | |
| 4 | D11 | PA7 | TMR3_CH2 / SPI1_MOSI | |
| 5 | D12 | PA6 | SPI1_MISO | |
| 6 | D13 | PA5 | SPI1_SCK | |
| 7 | GND | - | Ground | |
| 8 | I-AREF | - | Okukhiphayo kwe-VREF+ | |
| 9 | I-SDA | PB9 | I2C1_SDA | |
| 10 | I-SCL | PB8 | I-I2C1_SCL | |
| I-J7 (Abanye) | 1 | I-MISO | PB14 | SPI2_MISO |
| 2 | 5V | - | 5 V okokufaka/okuphumayo | |
| 3 | SCK | PB13 | SPI2_SCK |
| 4 | UMOSI | PB15 | SPI2_MOSI | |
| 5 | SETHA KABUSHA | I-NRST | Ukusetha kabusha kwangaphandle | |
| 6 | GND | - | Ground | |
| 7 | I-NSS | PB12 | SPI2_CS | |
| 8 | PB11 | PB11 | - |
- Bheka kuThebula 2 ukuze uthole imininingwane mayelana nezimbangi ezingu-0Ω.
3.11.2 LQFP144 I/O isixhumi esibonakalayo esinwetshiwe
Ama-I/Os we-AT-START-F435 microcontroller angaxhunywa kumadivayisi angaphandle ngokusebenzisa izixhumanisi zokunweba i-J1 ne-J2. Wonke ama-I/O aku-AT32F435ZMT7 ayatholakala kulezi zindawo zokunweba. I-J1 ne-J2 nayo ingalinganiswa nge-oscilloscope, i-logic analyzer noma i-voltmeter probe.
Okuhlelekile
 |
 |
 |
 |
Umlando wokubuyekeza
Ithebula 4. Umlando wokubuyekeza idokhumenti
| Usuku | Buyekeza | Izinguquko |
| 2021.11.20 | 1 | Ukukhishwa kokuqala |
ISAZISO ESIBALULEKILE - SICELA UFUNDE NGOKUQONDA
Abathengi bayaqonda futhi bayavuma ukuthi abathengi banesibopho kuphela sokukhethwa nokusetshenziswa kwemikhiqizo namasevisi e-Artery.
Imikhiqizo namasevisi e-Artery ahlinzekwa “NJENGOBA INGABE” futhi i-Artery ayihlinzeki ngeziqinisekiso ezivezwayo, ezishiwo noma ezingokomthetho, okuhlanganisa, ngaphandle komkhawulo, noma yiziphi iziqinisekiso ezisikiselwayo zokuthengiselana, ikhwalithi egculisayo, ukungephulwa komthetho, noma ukufaneleka ngenjongo ethile maqondana ne-Artery. imikhiqizo namasevisi.
Ngaphandle kwanoma yini ephambene, abathengi abalitholi ilungelo, isihloko noma inzalo kunoma yimiphi imikhiqizo namasevisi e-Artery nanoma imaphi amalungelo empahla yengqondo equkethwe kuyo. Akukho mcimbi lapho imikhiqizo namasevisi e-Artery ehlinzekiwe ayohunyushwa ngokuthi (a) ukunikeza abathengi, ngokucacile noma ngokusikisela, i-estoppel noma ngenye indlela, ilayisensi yokusebenzisa imikhiqizo namasevisi ezinkampani zangaphandle; noma (b) ngokunikeza ilayisensi amalungelo empahla yengqondo yabantu besithathu; noma (c) eqinisekisa imikhiqizo namasevisi enkampani yangaphandle namalungelo ayo empahla yengqondo. Abathengi ngalokhu bayavuma ukuthi imikhiqizo ye-Artery ayigunyaziwe ukuthi isetshenziswe, futhi abathengi ngeke bahlanganise, bakhuthaze, bathengise noma badlulisele noma yimuphi umkhiqizo we-Artery kunoma iliphi ikhasimende noma umsebenzisi wokugcina ukuze usetshenziswe njengezingxenye ezibalulekile (a) kunoma yikuphi ukwelashwa, ukonga impilo noma ukuphila. idivayisi noma uhlelo, noma (b) noma iyiphi idivayisi yokuphepha noma isistimu kunoma yiluphi uhlelo lwezimoto kanye nendlela (okuhlanganisa kodwa kungagcini nje ngamabhuleki ezimoto noma amasistimu ama-airbag), noma (c) noma yiziphi izinsiza zenuzi, noma (d) noma iyiphi idivayisi yokulawula ukuhamba emoyeni. , uhlelo noma uhlelo, noma (e) noma iyiphi idivayisi yezikhali, uhlelo lokusebenza noma isistimu, noma (f) noma iyiphi enye idivayisi, uhlelo lokusebenza noma uhlelo lapho kubonakala khona kusengaphambili ukuthi ukwehluleka kwemikhiqizo yoMcibisholo njengoba isetshenziswa kuleyo divayisi, isicelo noma uhlelo kungaholela ukufa, ukulimala komzimba noma ukulimala okuyinhlekelele kwempahla
© 2022 ARTERY Technology - Wonke amalungelo agodliwe
2021.11.20
Isambulo 1.00
Amadokhumenti / Izinsiza
 |
I-ARTERYTEK AT-START-F435 32 Bit Microcontrollers [pdf] Umhlahlandlela Womsebenzisi AT-START-F435, AT-START-F435 32 Bit Microcontrollers, 32 Bit Microcontrollers, Microcontrollers |