I-ARDUINO AKX00034 Edge Control Owner's
Incazelo
Ibhodi ye-Arduino® Edge Control yakhelwe ukubhekana nezidingo zokulima ngokunemba. Ihlinzeka ngesistimu yokulawula amandla aphansi, efanelekile ukuchelela ngokuxhumeka kwe-modular. Ukusebenza kwaleli bhodi kunganwetshwa ngamabhodi e-Arduino® MKR ukuze kunikezwe ukuxhumana okwengeziwe.
Izindawo eziqondiwe
Izilinganiso zezolimo, izinhlelo zokunisela ezihlakaniphile, ama-hydroponics
Izici
I-Nina B306 Module
Iphrosesa
- 64 MHz Arm® Cortex®-M4F (nge-FPU)
- 1 MB Flash + 256 KB RAM
Okungenantambo
- I-Bluetooth (BLE 5 ngesitaki se-Cordio®) Izandiso Zokukhangisa
- 95 dBm ukuzwela
- 4.8 mA ku-TX (0 dBm)
- 4.6 mA ku-RX (1 Mbps)
Amapheripheral
- Isivinini esigcwele 12 Mbps USB
- I-Arm® CryptoCell® CC310 uhlelo olungaphansi lwezokuphepha lwe-QSPI/SPI/TWI/I²S/PDM/QDEC
- Ijubane eliphezulu 32 MHz SPI
- I-Quad SPI interface 32 MHz
- 12-bit 200 ksps ADC
- 128 bit AES/ECB/CCM/AAR co-processor
Inkumbulo
- Imemori ye-Flash yangaphakathi engu-1 MB
- 2MB ebhodini le-QSPI
- Isikhala sekhadi le-SD
Amandla
- Amandla Aphansi
- 200uA Ukulala okwamanje
- Ingasebenza kuze kube yizinyanga ezingama-34 ngebhethri elingu-12V/5Ah
- I-12 V Acid/lead SLA Battery Supply (Ishajwa kabusha ngamaphaneli elanga) Ibhethri ye-RTC CR2032 Lithium yenza isipele
Ibhethri
- Ishaja yebhethri yephaneli yelanga ye-LT3652
- Okokufaka Voltage I-Regulation Loop ye-Peak Power Tracking ku-(MPPT) izinhlelo zokusebenza ze-Solar
I/O
- 6x izikhonkwane zokuvuka ezizwelayo
- 16x okokufaka kwenzwa ye-watermark ye-hydrostatic
- 8x 0-5V okokufaka kwe-analog
- 4x 4-20mA okokufaka
- 8x latching relay umyalo ophumayo enabashayeli
- 8x latching relay umyalo ophumayo ngaphandle abashayeli
- 4x 60V/2.5A ukudluliselwa kwesimo esiqinile esihlukaniswe ngamagalvani
- 6x 18 pin plug kuzixhumi zebhulokhi yetheminali
I-MKR Socket Emibili
- Ukulawula amandla komuntu ngamunye
- Imbobo ye-serial yomuntu ngamunye
- Izimbobo ze-I2C ngazinye
Ulwazi lokuphepha
- Ikilasi A
Ibhodi
Isicelo ExampLes
I-Arduino® Edge Control iyisango lakho le-Agriculture 4.0. Thola ukuqonda kwesikhathi sangempela mayelana nesimo senqubo yakho futhi wandise isivuno sezitshalo. Thuthukisa ukusebenza kahle kwebhizinisi ngokuzenzakalela kanye nokulima okuqagelayo. Yenza i-Edge Control ihambisane nezidingo zakho ngokusebenzisa amabhodi e-Arduino® MKR amabili kanye nezinhlobonhlobo zezihlangu ezihambisanayo. Gcina amarekhodi omlando, ukulawula ikhwalithi ngokuzenzakalelayo, sebenzisa ukuhlelwa kwezitshalo, nokuningi nge-Arduino IoT Cloud kusuka noma yikuphi emhlabeni.
Ama-Greenhouses azenzakalelayo
Ukuze kuncishiswe ukukhishwa kwekhabhoni futhi kwandiswe isivuno sezomnotho, kubalulekile ukuqinisekisa ukuthi indawo engcono kakhulu ihlinzekwa ukukhula kwezitshalo ngokomswakama, izinga lokushisa, nezinye izici. I-Arduino® Edge Control iyinkundla ehlanganisiwe eyenza ukuqapha okukude kanye nokwenza kahle kwesikhathi sangempela kuze kube manje. Kubandakanya i-Arduino® MKR GPS Shield (SKU: ASX00017) ivumela ukuhlelwa kokuzungezisa kwezitshalo kanye nokutholwa kwedatha ye-geospatial.
I-Hydroponics/Aquaponics
Njengoba i-hydroponics ihilela ukukhula kwezitshalo ngaphandle kwenhlabathi, ukunakekelwa okubucayi kufanele kugcinwe ukuze kuqinisekiswe ukuthi zigcina iwindi elincane elidingekayo ukuze zikhule kahle. I-Arduino Edge Control ingaqinisekisa ukuthi leli windi lifinyelelwa ngomsebenzi omncane wezandla. I-Aquaponics inganikeza izinzuzo eziningi nakakhulu kune-hydroponics evamile lapho i-Arduino®'s Edge Control ingasiza ukufanisa nezimfuneko eziphakeme nakakhulu ngokunikeza ukulawula okungcono kwenqubo yangaphakathi kuyilapho ekugcineni kunciphisa ubungozi bokukhiqiza.
Ukutshalwa Kwamakhowe: Amakhowe adume kabi ngokudinga izinga lokushisa elifanele kanye nomswakama ukuze aqhubekisele phambili ukukhula kwembewu ngenkathi evimbela ukukhula kwesikhunta esiqhudelanayo. Ngenxa yezinzwa eziningi ze-watermark, izimbobo zokuphuma, nezinketho zokuxhumana ezitholakala ku-Arduino® Edge Control kanye ne-Arduino® IoT Cloud, lokhu kulima okunembayo kungafinyelelwa ngezinga elingakaze libonwe.
Izesekeli.
- I-Irometer Tensiometers
- Izinzwa zokuswakama kwenhlabathi ye-Watermark
- Ama-valve ebhola enziwe ngomshini
- Iphaneli yelanga
- 12V/5Ah acid/lead SLA ibhethri (11 – 13.3V)
Imikhiqizo Ehlobene
- Isibonisi se-LCD + Ikhebula Eliyisicaba + indawo evalekile yepulasitiki
- 1844646 Oxhumana nabo basePhoenix (bafakwe nomkhiqizo)
- Amabhodi omndeni we-Arduino® MKR (okwandisa ukuxhumana okungenantambo)
Isixazululo sesiphelileview
Example yohlelo lokusebenza olujwayelekile lwesixazululo okuhlanganisa i-LCD Display namabhodi amabili e-Arduino® MKR 1300.
Izilinganiso
Izilinganiso Eziphelele Eziphelele
| Uphawu | Incazelo | Okuncane | Thayipha | Ubukhulu | Iyunithi |
| TMax | Umkhawulo wokushisa ophezulu | -40 | 20 | 85 | °C |
| I-VBattMax | Umthamo wokufaka omkhulutage kusuka kokufaka kwebhethri | -0.3 | 12 | 17 | V |
| I-VSolarMax | Umthamo wokufaka omkhulutage kusuka kuphaneli yelanga | -20 | 18 | 20 | V |
| I-ARElayMax | Ubuningi bamanje ngokushintsha kwe-relay | – | – | 2.4 | A |
| I-PMax | Ukusetshenziswa kwamandla okuphezulu | – | – | 5000 | mW |
Izimo Zokusebenza Ezinconyiwe
| Uphawu | Incazelo | Okuncane | Thayipha | Ubukhulu | Iyunithi |
| T | Imikhawulo yokushisa elondolozayo | -15 | 20 | 60 | °C |
| VBatt | Okokufaka ivoltage kusuka kokufaka kwebhethri | – | 12 | – | V |
| I-VSolar | Okokufaka ivoltage kusuka kuphaneli yelanga | 16 | 18 | 20 | V |
Isebenza Ngaphezuluview
I-Topology yebhodi
Phezulu View
| Ref. | Incazelo | Ref. | Incazelo |
| U1 | Ishaja yebhethri ye-LT3652HV IC | J3,7,9,8,10,11 | 1844798 amabhlogo wetheminali axhumekeka kalula |
| U2 | MP2322 3.3V isiguquli sebuck IC | I-LED1 | Ebhodini le-LED |
| U3 | MP1542 19V isiguquli sokuthuthukisa i-IC | PB1 | Setha kabusha inkinobho yokusunduza |
| U4 | I-TPS54620 5V i-boost converter IC | J6 | Ikhadi le-Micro SD |
| U5 | I-CD4081BNSR NEsango IC | J4 | CR2032 isibambi sebhethri |
| U6 | I-CD40106BNSR AKUYONA isango le-IC | J5 | I-Micro USB (NINA Module) |
| U12,U17 | I-MC14067BDWG multiplexer IC | U8 | I-TCA6424A IO yokwandisa i-IC |
| U16 | I-CD40109BNSRG4 I/O Expander | U9 | I-NINA-B306 Imojula |
| U18,19,20,21 | I-TS13102 isilayidi esiqinile se-IC | U10 | I-ADR360AUJZ-R2 Voltage-reference series 2.048V IC |
| Ref. | Incazelo | Ref. | Incazelo |
| U11 | I-W25Q16JVZPIQ Flash 16M IC | Q3 | I-ZXMP4A16GTA MOSFET P-CH 40V 6.4A |
| U7 | I-CD4081BNSR NEsango IC | U14, 15 | Idatha ye-MC14067BDWG IC MUX |
Iphrosesa
I-Main processor iyi-Cortex M4F egijima kufika ku-64MHz.
Isikrini se-LCD
I-Arduino® Edge Control inikeza isixhumi esizinikezele (J1) sokuxhumanisa ne-HD44780 16×2 LCD module yokubonisa, ethengiswa ngokuhlukana. Iprosesa eyinhloko ilawula i-LCD nge-TCA6424 port expander ngaphezu kwe-I2C. Idatha idluliswa ngesixhumi esibonakalayo esingu-4-bit. Ukuqina kwe-backlight ye-LCD nakho kungalungiswa yi-processor eyinhloko.
Izinzwa ze-Analog ezingu-5V
Okokufaka kwe-analog okungafika kweyisishiyagalombili okungu-0-5V kungaxhunywa ku-J4 ukuze kusetshenziswe izinzwa ze-analog ezifana nama-tensiometer nama-dendrometers. Okokufaka kuvikelwa yi-19V Zener diode. Okokufaka ngakunye kuxhunywe ku-multiplexer ye-analog ehambisa isignali embotsheni eyodwa ye-ADC. Okokufaka ngakunye kuxhunywe ku-analog multiplexer (MC14067) ehambisa isignali embotsheni eyodwa ye-ADC. Iphrosesa eyinhloko ilawula ukukhethwa kokufaka nge-TCA6424 port expander ngaphezu kwe-I2C.
4-20mA Izinzwa
Kungaxhunywa izinzwa ezine ze-4-20mA ku-J4. I-reference voltagI-e ye-19V ikhiqizwa isiguquli se-MP1542 sokukhuphuka ukuze sinikeze amandla iluphu yamanje. Inani lenzwa lifundwa nge-resistor engu-220 ohm. Okokufaka ngakunye kuxhunywe ku-analog multiplexer (MC14067) ehambisa isignali embotsheni eyodwa ye-ADC. Iphrosesa eyinhloko ilawula ukukhethwa kokufaka nge-TCA6424 port expander ngaphezu kwe-I2C.
Izinzwa ze-Watermark
Kungaxhunywa izinzwa ze-watermark ze-hydrostatic ezingafika kweziyishumi nesithupha ku-J8. Izikhonkwane i-J8-17 ne-J8-18 yizikhonkwane ezivamile zazo zonke izinzwa, ezilawulwa ngokuqondile yi-microcontroller. Okokufaka namaphinikhodi enzwa ajwayelekile kuvikelwa yi-19V Zener diode. Okokufaka ngakunye kuxhunywe ku-analog multiplexer (MC14067) ehambisa isignali embotsheni eyodwa ye-ADC. Iphrosesa eyinhloko ilawula ukukhethwa kokufaka nge-TCA6424 port expander ngaphezu kwe-I2C. Ibhodi lisekela izindlela ezi-2 zokunemba.
Latching Outputs
Izixhumi i-J9 ne-J10 zihlinzeka ngemiphumela kumadivayisi okuxhunywa njengama-valve anenjini. I-latching ephumayo iqukethe amashaneli akabili (P kanye no-N) okungathunyelwa ngawo impulse noma i-strobe kunoma iyiphi ishaneli emi-2 (ukuvula i-valve yokuvala ye-ex.ample). Ubude besikhathi se-strobes bungahle bulungiswe ukuze buhambisane nesidingo sedivayisi yangaphandle. Ibhodi lihlinzeka ngenani lamachweba wokunamathisela ayi-16 ahlukaniswe ngezinhlobo ezi-2:
- Imiyalo yokuqhafaza (J10): Izimbobo eziyi-8 zokufakwa kwe-impedance ephezulu (ubukhulu +/- 25 mA). Xhuma kumadivayisi angaphandle anokuvikela/amasekhethi amandla enkampani yangaphandle. Kubhekiselwe ku-VBAT.
- I-Latching Out (J9): Izimbobo eziyi-8. Lokhu okukhiphayo kufaka phakathi izishayeli zedivayisi yokuxhuma. Abekho abashayeli bangaphandle abadingekayo. Kubhekiselwe ku-VBAT.
I-Solid State Relays
Ibhodi inezici ezine ezilungisekayo ze-60V 2.5A zesimo esiqinile esine-galvanic isolation etholakala ku-J11. Izinhlelo zokusebenza ezijwayelekile zifaka i-HVAC, isilawuli sokufafaza njll.
Isitoreji
Ibhodi lihlanganisa kokubili isokhethi yekhadi le-microSD kanye nememori ye-flash engu-2MB eyengeziwe yokugcina idatha. Zombili zixhunywe ngokuqondile kuphrosesa eyinhloko ngesixhumi esibonakalayo se-SPI.
Isihlahla Samandla
Ibhodi linganikwa amandla ngamaphaneli elanga kanye/noma amabhethri e-SLA.
Ukusebenza kwebhodi
Ukuqalisa - IDE
Uma ufuna ukuhlela i-Arduino® Edge Control yakho ngenkathi ungaxhunyiwe kufanele ufake i-Arduino® Desktop IDE [1] Ukuze uxhume isilawuli se-Arduino® Edge kukhompyutha yakho, uzodinga intambo ye-USB ye-Micro-B. Lokhu futhi kunikeza amandla ebhodini, njengoba kuboniswe yi-LED.
Ukuqala - Arduino Web Mhleli
Wonke amabhodi e-Arduino®, okuhlanganisa naleli, asebenza ngaphandle kwebhokisi ku-Arduino® Web Umhleli [2], ngokufaka nje i-plugin elula. I-Arduino® Web Umhleli usingathwa ku-inthanethi, ngakho-ke uzohlala usesikhathini samanje ngezici zakamuva nokusekelwa kwawo wonke amabhodi. Landela i-[3] ukuze uqale ukubhala amakhodi esipheqululini futhi ulayishe imidwebo yakho ebhodini lakho.
Ukuqalisa - I-Arduino IoT Cloud
Yonke imikhiqizo enikwe amandla i-Arduino® IoT isekelwa ku-Arduino® IoT Cloud ekuvumela ukuthi Ungene, udwebe futhi uhlaziye idatha yezinzwa, ucuphe imicimbi, futhi wenze ikhaya lakho noma ibhizinisi lakho ngokuzenzakalelayo.
Sample Sketches
Sampimidwebo ye-Arduino® Edge Control ingatholakala ku-“Examples” kumenyu ye-Arduino® IDE noma esigabeni esithi “Documentation” se-Arduino® Pro webindawo [4]
Izinsiza eziku-inthanethi
Manje njengoba usudlule ezintweni eziyisisekelo zalokho ongakwenza ngebhodi ungakwazi ukuhlola amathuba angapheli eliwahlinzekayo ngokubheka amaphrojekthi ajabulisayo ku-ProjectHub [5], i-Arduino® Library Reference [6] kanye nesitolo se-inthanethi [7] lapho uzokwazi ukugcwalisa ibhodi lakho ngezinzwa, ama-actuator nokuningi.
Ukubuyiselwa Kwebhodi
Wonke amabhodi e-Arduino® ane-bootloader eyakhelwe ngaphakathi evumela ukucwayiza ibhodi nge-USB. Uma kwenzeka umdwebo uvala iphrosesa futhi ibhodi lingasatholakali nge-USB ungakwazi ukufaka imodi ye-bootloader ngokuthepha kabili inkinobho yokusetha kabusha ngemva nje kokukhanyisa.
Ama-Pinout wokuxhuma
I-J1 LCD Isixhumi
| Phina | Umsebenzi | Uhlobo | Incazelo |
| 1 | I-PWM | Amandla | I-Backlight LED Cathode (PWM control) |
| 2 | Vula | Idijithali | Okokufaka kwenkinobho |
| 3 | +5V LCD | Amandla | Ukunikezwa kwamandla kwe-LCD |
| 4 | I-LCD RS | Idijithali | Isiginali ye-LCD RS |
| 5 | Qhathanisa | I-Analog | I-LCD Contrast control |
| 6 | I-LCD RW | Idijithali | Isignali ye-LCD Funda/Bhala |
| 7 | I-LED+ | Amandla | I-Backlight LED Anode |
| 8 | LCD EN | Idijithali | I-LCD Vumela isignali |
| 10 | I-LCD D4 | Idijithali | Isignali ye-LCD D4 |
| 12 | I-LCD D5 | Idijithali | Isignali ye-LCD D5 |
| 14 | I-LCD D6 | Idijithali | Isignali ye-LCD D6 |
| 16 | I-LCD D7 | Idijithali | Isignali ye-LCD D7 |
| 9,11,13,15 | GND | Amandla | Ground |
Izimpawu zokuvuka ze-J3/Imiyalo yokudlulisa yangaphandle
| Phina | Umsebenzi | Uhlobo | Incazelo |
| 1,3,5,7,9 | V I-BAT | Amandla | I-Gated voltagibhethri yereferensi yesignali yokuvuka |
| 2,4,6,8,10,12 | Okokufaka | Idijithali | Izimpawu zokuvuka ezibucayi |
| 13 | Okukhiphayo | Idijithali | Isignali yewashi lewashi lesimo esiqinile sangaphandle 1 |
| 14 | Okukhiphayo | Idijithali | Isignali yewashi lewashi lesimo esiqinile sangaphandle 2 |
| 17 | I-Bidir | Idijithali | Isignali yedatha yesimo esiqinile sangaphandle 1 |
| 18 | I-Bidir | Idijithali | Isignali yedatha yesimo esiqinile sangaphandle 2 |
| 15,16 | GND | Amandla | Ground |
I-J5 USB
| Phina | Umsebenzi | Uhlobo | Incazelo |
| 1 | I-VUSB | Amandla | Inothi Lokufaka Lokufaka Amandla: Ibhodi elinikwe amandla nge-V USB kuphela ngeke livumele izici eziningi zebhodi. Hlola isihlahla samandla eSigabeni 3.8 |
| 2 | D- | Okuhlukile | Idatha ehlukile ye-USB - |
| 3 | D+ | Okuhlukile | Idatha ehlukile ye-USB + |
| 4 | ID | NC | Engasetshenzisiwe |
| 5 | GND | Amandla | Ground |
I-J7 Analog/4-20mA
| Phina | Umsebenzi | Uhlobo | Incazelo |
| 1,3,5,7 | +19V | Amandla | 4-20mA ivolumutage reference |
| 2 | IN1 | I-Analog | 4-20mA okokufaka 1 |
| 4 | IN2 | I-Analog | 4-20mA okokufaka 2 |
| 6 | IN3 | I-Analog | 4-20mA okokufaka 3 |
| 8 | IN4 | I-Analog | 4-20mA okokufaka 4 |
| 9 | GND | Amandla | Ground |
| 10 | +5V | Amandla | 5V okukhiphayo kwereferensi ye-analog engu-0-5V |
| 11 | A5 | I-Analog | 0-5V okokufaka 5 |
| 12 | A1 | I-Analog | 0-5V okokufaka 1 |
| 13 | A6 | I-Analog | 0-5V okokufaka 6 |
| 14 | A2 | I-Analog | 0-5V okokufaka 2 |
| 15 | A7 | I-Analog | 0-5V okokufaka 7 |
| 16 | A3 | I-Analog | 0-5V okokufaka 3 |
| 17 | A8 | I-Analog | 0-5V okokufaka 8 |
| 18 | A4 | I-Analog | 0-5V okokufaka 4 |
I-J8 Watermark
| Phina | Umsebenzi | Uhlobo | Incazelo |
| 1 | AmanziMrk1 | I-Analog | Okokufaka kwe-Watermark 1 |
| 2 | AmanziMrk2 | I-Analog | Okokufaka kwe-Watermark 2 |
| 3 | AmanziMrk3 | I-Analog | Okokufaka kwe-Watermark 3 |
| 4 | AmanziMrk4 | I-Analog | Okokufaka kwe-Watermark 4 |
| 5 | AmanziMrk5 | I-Analog | Okokufaka kwe-Watermark 5 |
| 6 | AmanziMrk6 | I-Analog | Okokufaka kwe-Watermark 6 |
| 7 | AmanziMrk7 | I-Analog | Okokufaka kwe-Watermark 7 |
| 8 | AmanziMrk8 | I-Analog | Okokufaka kwe-Watermark 8 |
| 9 | AmanziMrk9 | I-Analog | Okokufaka kwe-Watermark 9 |
| 10 | AmanziMrk10 | I-Analog | Okokufaka kwe-Watermark 10 |
| 11 | AmanziMrk11 | I-Analog | Okokufaka kwe-Watermark 11 |
| 12 | AmanziMrk12 | I-Analog | Okokufaka kwe-Watermark 12 |
| 13 | AmanziMrk13 | I-Analog | Okokufaka kwe-Watermark 13 |
| 14 | AmanziMrk14 | I-Analog | Okokufaka kwe-Watermark 14 |
| Phina | Umsebenzi | Uhlobo | Incazelo |
| 15 | AmanziMrk15 | I-Analog | Okokufaka kwe-Watermark 15 |
| 16 | AmanziMrk16 | I-Analog | Okokufaka kwe-Watermark 16 |
| 17,18 | I-VCOMMON | Idijithali | Inzwa evamile voltage |
I-J9 Latching Out (+/- VBAT)
| Phina | Umsebenzi | Uhlobo | Incazelo |
| 1 | PULSE_OUT0_P | Idijithali | I-Latching okukhiphayo okungu-1 okuhle |
| 2 | PULSE_OUT0_N | Idijithali | I-Latching okukhiphayo okungu-1 okunegethivu |
| 3 | PULSE_OUT1_P | Idijithali | I-Latching okukhiphayo okungu-2 okuhle |
| 4 | PULSE_OUT1_N | Idijithali | I-Latching okukhiphayo okungu-2 okunegethivu |
| 5 | PULSE_OUT2_P | Idijithali | I-Latching okukhiphayo okungu-3 okuhle |
| 6 | PULSE_OUT2_N | Idijithali | I-Latching okukhiphayo okungu-3 okunegethivu |
| 7 | PULSE_OUT3_P | Idijithali | I-Latching okukhiphayo okungu-4 okuhle |
| 8 | PULSE_OUT3_N | Idijithali | I-Latching okukhiphayo okungu-4 okunegethivu |
| 9 | PULSE_OUT4_P | Idijithali | I-Latching okukhiphayo okungu-5 okuhle |
| 10 | PULSE_OUT4_N | Idijithali | I-Latching okukhiphayo okungu-5 okunegethivu |
| 11 | PULSE_OUT5_P | Idijithali | I-Latching okukhiphayo okungu-6 okuhle |
| 12 | PULSE_OUT5_N | Idijithali | I-Latching okukhiphayo okungu-6 okunegethivu |
| 13 | PULSE_OUT6_P | Idijithali | I-Latching okukhiphayo okungu-7 okuhle |
| 14 | PULSE_OUT6_N | Idijithali | I-Latching okukhiphayo okungu-7 okunegethivu |
| 15 | PULSE_OUT7_P | Idijithali | I-Latching okukhiphayo okungu-8 okuhle |
| 16 | PULSE_OUT7_N | Idijithali | I-Latching okukhiphayo okungu-8 okunegethivu |
| 17,18 | GND | Amandla | Ground |
I-J10 Latching Command (+/- VBAT)
| Phina | Umsebenzi | Uhlobo | Incazelo |
| 1 | STOBE8_P | Idijithali | Latching umyalo 1 omuhle |
| 2 | STOBE8_N | Idijithali | Latching umyalo 1 negative |
| 3 | STOBE9_P | Idijithali | Latching umyalo 2 omuhle |
| 4 | STOBE9_N | Idijithali | Latching umyalo 2 negative |
| 5 | STOBE10_P | Idijithali | Latching umyalo 3 omuhle |
| 6 | STOBE10_N | Idijithali | Latching umyalo 3 negative |
| 7 | STOBE11_P | Idijithali | Latching umyalo 4 omuhle |
| 8 | STOBE11_N | Idijithali | Latching umyalo 4 negative |
| 9 | STOBE12_N | Idijithali | Latching umyalo 5 omuhle |
| 10 | STOBE12_P | Idijithali | Latching umyalo 5 negative |
| 11 | STOBE13_P | Idijithali | Latching umyalo 6 omuhle |
| 12 | STOBE13_N | Idijithali | Latching umyalo 6 negative |
| 13 | STOBE14_P | Idijithali | Latching umyalo 7 omuhle |
| 14 | STOBE14_N | Idijithali | Latching umyalo 7 negative |
| 15 | STOBE15_P | Idijithali | Latching umyalo 8 omuhle |
| 16 | STOBE15_N | Idijithali | Latching umyalo 8 negative |
| Phina | Umsebenzi | Uhlobo | Incazelo |
| 17 | GATED_VBAT_PULSE | Amandla | Itheminali e-Gated Positive yebhethri |
| 18 | GND | Amandla | Ground |
I-J11 Relay (+/- VBAT)
| Phina | Umsebenzi | Uhlobo | Incazelo |
| 1 | I-SOLAR+ | Amandla | I-Solar Panel Positive Terminal |
| 2 | NC | NC | Engasetshenzisiwe |
| 3 | GND | Amandla | Ground |
| 4 | RELAY1_P | Shintsha | Dlulisa oku-1 okuhle |
| 5 | NC | NC | Engasetshenzisiwe |
| 6 | RELAY1_N | Shintsha | Dlulisa oku-1 okunegethivu |
| 7 | NC | NC | Engasetshenzisiwe |
| 8 | RELAY2_P | Shintsha | Dlulisa oku-2 okuhle |
| 9 | NC | NC | Engasetshenzisiwe |
| 10 | RELAY2_N | Shintsha | Dlulisa oku-2 okunegethivu |
| 11 | 10kGND | Amandla | Ground nge-10k resistor |
| 12 | RELAY3_P | Shintsha | Dlulisa oku-3 okuhle |
| 13 | I-NTC | I-Analog | I-thermoresistor ye-thermoresistor ene-negative temperatures coeffcient (NTC). |
| 14 | RELAY3_N | Shintsha | Dlulisa oku-3 okunegethivu |
| 15 | GND | Amandla | Ground |
| 16 | RELAY4_P | Shintsha | Dlulisa oku-4 okuhle |
| 17 | IBHETHA + | Amandla | Itheminali Yebhethri Positive |
| 18 | RELAY4_N | Shintsha | Dlulisa oku-4 okunegethivu |
Ulwazi Lwemishini
Uhlaka Lwebhodi
Izimbobo Okufakwayo
Izikhundla zesixhumi
Izitifiketi
Simemezela ngaphansi kwesibopho sethu sodwa ukuthi imikhiqizo engenhla ihambisana nezidingo ezibalulekile ze-EU Directives futhi ngenxa yalokho ifanelekela ukuhamba mahhala ezimakethe ezihlanganisa i-European Union (EU) kanye ne-European Economic Area (EEA).
Isimemezelo Sokuvumelana ne-EU RoHS & REACH 211 01/19/2021
Amabhodi e-Arduino ahambisana ne-RoHS 2 Directive 2011/65/EU ye-European Parliament kanye ne-RoHS 3 Directive 2015/863/EU yoMkhandlu wangomhla zizi-4 kuJuni 2015 mayelana nokukhawulelwa kokusetshenziswa kwezinto ezithile eziyingozi ezintweni zikagesi neze-elekthronikhi.
| Into | Umkhawulo Omkhulu (ppm) |
| Ukuhola (Pb) | 1000 |
| I-Cadmium (Cd) | 100 |
| I-Mercury (Hg) | 1000 |
| I-Hexavalent Chromium (Cr6+) | 1000 |
| I-Poly Brominated Biphenyls (PBB) | 1000 |
| I-Poly Brominated Diphenyl ethers (PBDE) | 1000 |
| I-Bis(2-Ethylhexyl} phthalate (DEHP) | 1000 |
| I-Benzyl butyl phthalate (BBP) | 1000 |
| I-Dibutyl phthalate (DBP) | 1000 |
| IDiisobutyl phthalate (DIBP) | 1000 |
Ukukhululwa : Akukho ukukhululwa okufunayo.
Amabhodi e-Arduino athobelana ngokugcwele nezimfuneko ezihlobene ze-European Union Regulation (EC) 1907/2006 eziphathelene noBhaliso, Ukuhlola, Ukugunyazwa Nokukhawulwa Kwamakhemikhali (REACH). Simemezela ukuthi awekho ama-SVHC (https://echa.europa.eu/web/ithebula lesivakashi/lamakhandidethi), Uhlu Lwabakhandidethi Lwezinto Ezikhathazayo Eziphakeme Kakhulu ngokugunyazwa okwamanje olukhishwe yi-ECHA, lukhona kuyo yonke imikhiqizo (kanye nephakeji) ngamanani anengqikithi yokuhlushwa elingana noma engaphezu kuka-0.1%. Ngokwazi kwethu konke, siphinde simemezele ukuthi imikhiqizo yethu ayinazo izinto ezisohlwini “Lolugunyazo” (Isijobelelo XIV semithetho ye-REACH) kanye Nezinto Ezikhathazayo Kakhulu (SVHC) kunoma yimaphi amanani abalulekile njengoba kushiwo. yi-Annex XVII yohlu lwabazokhethwa olushicilelwe yi-ECHA (European Chemical Agency) 1907 /2006/EC.
Isimemezelo Sezimbiwa Ezingqubuzanayo
Njengomphakeli womhlaba wonke wezingxenye zikagesi nezikagesi, i-Arduino iyazazi izibopho zethu maqondana nemithetho nemithethonqubo ephathelene ne-Conflict Minerals, ikakhulukazi i-Dodd-Frank Wall Street Reform and Consumer Protection Act, Isigaba 1502. I-Arduino ayikhiphi ngokuqondile noma icubungule ukungqubuzana amaminerali afana ne-tin, i-Tantalum, i-Tungsten, noma igolide. Amaminerali angqubuzanayo aqukethwe emikhiqizweni yethu ngendlela ye-solder, noma njengengxenye yama-alloys ensimbi. Njengengxenye yokukhuthala kwethu okunengqondo i-Arduino ithinte abahlinzeki bengxenye ngaphakathi kochungechunge lwethu lokuhlinzeka ukuze baqinisekise ukuqhubeka kwabo nokuthobela imithetho. Ngokusekelwe olwazini esilutholile kuze kube manje simemezela ukuthi imikhiqizo yethu iqukethe Amaminerali Aphikisanayo atholakala ezindaweni ezingenazo izingxabano.
Isexwayiso se-FCC
Noma yiziphi Izinguquko noma ukuguqulwa okungagunyazwanga ngokucacile yinhlangano enesibopho sokuthobela imithetho kungasusa igunya lomsebenzisi lokusebenzisa okokusebenza.
Le divayisi ithobela ingxenye 15 yeMithetho ye-FCC. Ukusebenza kungaphansi kwemibandela emibili elandelayo:
- Le divayisi ingase ingabangeli ukuphazamiseka okuyingozi
- lolu cingo kufanele lwamukele noma yikuphi ukuphazamiseka okutholiwe, okuhlanganisa ukuphazamiseka okungase kubangele ukusebenza okungafuneki.
Isitatimende Sokuchayeka Kwe-FCC RF:
- Lesi Transmitter akufanele sibekwe endaweni eyodwa noma sisebenze ngokuhlangana nanoma iyiphi enye i-antenna noma isidluliseli.
- Lokhu okokusebenza kuthobelana nemikhawulo yokuchayeka emisebeni ye-RF ebekwe endaweni engalawuleki.
- Lo mshini kufanele ufakwe futhi usebenze ngebanga elincane elingama-20cm phakathi kwerediyetha nomzimba wakho.
IsiZulu: Amamanuwali omsebenzisi wezinsiza zomsakazo ezikhishwe ilayisense azoqukatha isaziso esilandelayo noma esifanayo endaweni esobala kumanuwali yomsebenzisi noma ngenye indlela kudivayisi noma kokubili. Le divayisi ithobelana nezinga le-RSS elikhishwe yi-Industrial Canada. Ukusebenza kungaphansi kwemibandela emibili elandelayo:
- le divayisi ingase ingabangeli ukuphazamiseka
- lolu cingo kufanele lwamukele noma yikuphi ukuphazamiseka, okuhlanganisa ukuphazamiseka okungase kubangele ukusebenza okungafunwa kocingo.
Isexwayiso se-IC SAR
IsiZulu Lo mshini kufanele ufakwe futhi usebenze ngebanga elincane elingama-20 cm phakathi kwerediyetha nomzimba wakho.
Okubalulekile: Izinga lokushisa lokusebenza le-EUT alikwazi ukweqa u-85℃ futhi akufanele libe ngaphansi kuka -40℃.
| Amabhendi wemvamisa | Amandla amakhulu okukhipha (ERP) |
| 2402-2480Mhz | 3.35dbm |
Ngalokhu, i-Arduino Srl imemezela ukuthi lo mkhiqizo uthobela izimfuneko ezibalulekile nezinye izinhlinzeko ezifanele ze-Directive 201453/EU. Lo mkhiqizo uvunyelwe ukusetshenziswa kuwo wonke amazwe angamalungu e-EU.
Ulwazi Lwenkampani
| Igama Lenkampani | I-Arduino Srl |
| Ikheli Lenkampani | Via Andrea Appiani 25, 20900 Monza, Italy |
Imibhalo Eyisethenjwa
| Ref | Isixhumanisi |
| I-Arduino® IDE (Ideskithophu) | https://www.arduino.cc/en/Main/Software |
| I-Arduino® IDE (Ifu) | https://create.arduino.cc/editor |
| I-Arduino® Cloud IDE Ukuqalisa | https://create.arduino.cc/projecthub/Arduino_Genuino/getting-started-with- arduino-web-editor-4b3e4a |
| I-Arduino® Pro Webindawo | https://www.arduino.cc/pro |
| Ihabhu Yephrojekthi | https://create.arduino.cc/projecthub?by=part&part_id=11332&sort=trending |
| Ireferensi Yelabhulali | https://github.com/bcmi- labs/Arduino_EdgeControl/tree/4dad0d95e93327841046c1ef80bd8b882614eac8 |
| Isitolo Esiku-inthanethi | https://store.arduino.cc/ |
Shintsha ilogi
| Usuku | Buyekeza | Izinguquko |
| 21/02/2020 | 1 | Ukukhishwa Kokuqala |
| 04/05/2021 | 2 | Isibuyekezo sokuklama/isakhiwo |
| 30/12/2021 | 3 | Izibuyekezo zolwazi |
Amadokhumenti / Izinsiza
 |
I-ARDUINO AKX00034 Edge Control [pdf] Incwadi Yomnikazi AKX00034, 2AN9S-AKX00034, 2AN9SAKX00034, AKX00034 Edge Control, Edge Control |
