Okuqukethwe fihla
1 ALLMATIC CONTROL UNIT BIOS2 Programmable Control Board
2 introduzione
3 Ukucushwa
4 Ukuxhumana
5 UKUNIKEZELWA KWAMANDLA AMAPHOTOCELLS
6 Ukufunda ngesilawuli kude
7 Ukusetha i-wing stroke
8 Imenyu
8.1 Incazelo yemenyu
8.2 Imenyu ethuthukisiwe
9 Isimo seyunithi yokubonisa nokulawula
10 Izici zobuchwepheshe
11 Izimoto
12 QINISEKISA
13 Amadokhumenti / Izinsiza
13.1 Izithenjwa
14 Okuthunyelwe Okuhlobene

ALLMATIC-logo

ALLMATIC CONTROL UNIT BIOS2 Programmable Control Board

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-product

I-ALLMATIC Srl 32026 Borgo Valbelluna – Belluno – Italy Via dell'Artigiano, n°1 – ZA Tel. 0437 751175 - 751163 ra Fax 0437 751065 http://www.allmatic.com - I-imeyili: info@allmatic.com

introduzione

Iyunithi yokulawula i-BIOS2 ikhonjiswe ikakhulukazi ukufakwa kwamasango amaphiko angu-1 noma ama-2 anamamotho angama-230 Vac anamandla amakhulu amunca angu-700W. Iyunithi yokulawula ifakwe isibonisi esivumela ukulawulwa okunembile kokuphonswa kwamasango nokuzwela. Kungenzeka futhi ukulungisa ukubambezeleka kokuvalwa kwephiko lesibili kumenyu yezilungiselelo zesisekelo. Iyunithi yokulawula ingakwazi ngekhanda kufika kuma-transmitters angu-8000 ngememori yangaphandle, ngesinyathelo-by-step, ukuvula ingxenye, ukuvula, nokuvala imisebenzi. Inikezwa okokufaka kwe-photocell yangaphakathi nengaphandle, unqenqema lokuphepha (omshini noma i-8k2), okungenzeka ukuxhuma izinkinobho zesinyathelo ngesinyathelo, ukuvula ingxenye, ukuvula, ukuvala, nokumisa. Okuphumayo kuhlanganisa ukukhanya okukhanyayo okungu-230 Vac, ukukhiya kagesi 12 Vac 15 VA noma ngekhadi lokunweba u-R1 (akuhlinzekiwe) elinokuxhumana okomile 230 Vac 5A max/30 Vdc 5A max, isibani sokukhanya/isibani sendawo/isibani sesango elivulekile, 24 Vac /dc izesekeli amandla kagesi.

QAPHELA: UNGAFAKA IPHAKATHI LOKULAWULA NGAPHANDLE UKUFUNDA IMIYALELO KUQALA !!! UKUFAKA KUFANELE KWENZIWE ABASEBENZI ABAQINISEKILE KUPHELA.

  • Ukuze kusebenze kahle uhlelo, kubaluleke kakhulu ukusetshenziswa kwezitobhi zemishini ekuvuleni nasekuvaleni.

Ukucushwa

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-1

Ukuxhumana

UKUNIKEZWA KWAMANDLA KAGESI
Xhuma ikhebula lokunikezela kwamandla phakathi kwe-clamps 1 kanye no-2 weyunithi yokulawula

MOTOR 1 OUTPUT

  • Xhuma okuvamile kwe-motor 1 ku-clamp 5 weyunithi yokulawula.
  • Xhuma isigaba 1 se-motor 1 ku-clamp 3 weyunithi yokulawula.
  • Xhuma isigaba 2 se-motor 1 ku-clamp 4 weyunithi yokulawula.

MOTOR 2 OUTPUT

  • Xhuma okuvamile kwe-motor 2 ku-clamp 8 weyunithi yokulawula.
  • Xhuma isigaba 1 se-motor 2 ku-clamp 6 weyunithi yokulawula.
  • Xhuma isigaba 2 se-motor 2 ku-clamp 7 weyunithi yokulawula.

Amandla kagesi 230 Vac 50 Hz Ungalixhumi ikhadi ngqo kunethiwekhi kagesi. Faka idivayisi engaqinisekisa ukunqanyulwa kwesigxobo ngasinye ekunikezeni amandla eyunithi yokulawula.

Xhuma kokuphumayo kwe-MOTOR 1 iphiko elishayayo. Faka isikhiya sikagesi esivele sikhona kulolu phiko. I-MOTOR 1 ihlale isebenza kuqala phakathi nesigaba sokuvula futhi okwesibili phakathi nesigaba sokuvala.

  • Ama-motor condensers 230 Vac !Ingozi yokushaqeka ngogesi!
  • Esimeni lapho kusetshenziswa amamotho okungezona e-Allmatic, faka i-fuse ochungechungeni lwenjini evamile (bona isigaba 9)I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-2
  • Amandla kagesi 230 Vac 50 Hz Ungalixhumi ikhadi ngqo kunethiwekhi kagesi. Faka idivayisi engaqinisekisa ukunqanyulwa kwesigxobo ngasinye ekunikezeni amandla eyunithi yokulawula.
  • Xhuma kokuphumayo kwe-MOTOR 1 iphiko elishayayo. Faka isikhiya sikagesi esivele sikhona kulolu phiko. I-MOTOR 1 ihlale isebenza kuqala phakathi nesigaba sokuvula futhi okwesibili phakathi nesigaba sokuvala.
    • Ama-motor condensers 230 Vac !Ingozi yokushaqeka ngogesi!
  • Esimeni lapho kusetshenziswa amamotho okungezona e-Allmatic, faka i-fuse ochungechungeni lwenjini evamile (bheka isigaba 9)Z

UKUPHUMA OKUKHANYA NGOKUTHEMBEKA
Xhuma isibani senhlonipho ku-clamps 9 kanye no-10, 230Vac 100W MAX.

I-Flashing LIGHT OUTPUT
Xhuma ukukhanya okukhanyayo ku-clamps11 kanye 12.

IZISEKELO IMIPHUMELA
 Izinsiza eziphumayo 24Vac 9W max.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-3

UKUPHUMA KOKUKHIWA KAgesi
12Vac 15VA

Ukusebenza kwesikhiya sikagesi kulawulwa kumenyu ethuthukisiwe I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-43

UKUNIKEZELWA KWAMANDLA AMAPHOTOCELLS

  • Xhuma i-clamp 17 yeyunithi yokulawula ku-clamp + kokunikezwa kwamandla kwesamukeli sama-photocell.
  • Xhuma i-clamp 18 yeyunithi yokulawula endaweni yokuphakelwa kwamandla kagesiamp - yomamukeli we-photocell kanye ne-transmitter.
  • Xhuma i-clamp 19 yeyunithi yokulawula endaweni yokuphakelwa kwamandla kagesiamp i-transmitter yama-photocells.

Ukuhlolwa kwe-photocell kwenziwa kusebenze kumenyu ethuthukisiwe I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-32.

QAPHELA: iyunithi yokulawula inikeza ivolumutage ye-24 Vdc futhi ingahlinzeka ngamandla amakhulu angu-3.5W. Ngokuhlolwa konqenqema lokuphepha xhuma idivayisi yokuhlola yonqenqema lokuphepha kumaphini kagesi we-TX (isivivinyo senziwe sasebenza nge-wiht low logic signal 0Vdc). Sicela ubheke imanuwali yomkhawulo wokuphepha.

I-SAFETY EDGE INPUT
Xhuma oxhumana nabo bonqenqemeni lokuphepha ku-clamps 20 kanye no-21 weyunithi yokulawula. Khetha uhlobo lomkhawulo wokuvikela osetshenzisiwe (owomshini noma i-8K2) ngemenyu I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-33, khetha uhlobo lokusebenza ngemenyuI-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-34.
Uma ingasetshenziswanga setha i-DIP switch EDGE ON.

UKUVALA OKUFAKAYO KWE-PHOTOCELL
Xhuma othintana naye OVALIWE NGOKUJWAYELEKILE we-photocell (ISITHOMBE 1) phakathi kwe-clamps 23 kanye no-29 weyunithi yokulawula. Ukusebenza kwe-photocell yokuvula kulawulwa kumenyu ethuthukisiwe ph2 .Uma ingasetshenziswa setha iswishi ye-DIP engu-PH2 VALIWE.

MISA OKUFAKAYO
Xhuma othintana naye NGOKUVAMILE OVALIWE ku-STOP phakathi kwe-clamps 24 kanye no-29 weyunithi yokulawula. Uma ingasetshenziswanga setha inkinobho ye-DIP IVULIWE.

VULA OKUFAKAYO
Xhuma inkinobho ethi VULA phakathi kwe-clamps 25 no-29 weyunithi yokulawula.

VALA OKUFAKAYO
Xhuma inkinobho VALA phakathi kwe-clamps 26 no-29 weyunithi yokulawula.

OKUFAKAYO OKUVULA INGXENYE
Xhuma inkinobho ethi PED phakathi kwe-clamps 27 no-29 weyunithi yokulawula.

OKUFAKAYO IZINYATHELO NGESINYATHELO
Xhuma inkinobho ye-SS phakathi kwe-clamps 25 no-28 weyunithi yokulawula.

I-ANTENNA
Xhuma intambo yesiginali yothi ku-clamp 31 kanye nomhlabathi wothi clamp 30 weyunithi yokulawula. Ukuba khona kwezingxenye zensimbi noma umswakama ezindongeni kungaba nomthelela omubi kububanzi besistimu. Ngakho-ke siphakamisa ukuthi singabeki uthi olutholayo kanye/noma ama-transmitter eduze kwezinto ezinkulu zensimbi, eduze naphansi noma phansi.I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-4 I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-5

Ukufunda ngesilawuli kude

Ukufunda kwe-transmitter eyodwa
Ukhiye we-1 obanjwe ngekhanda wenza umsebenzi we-STEP by STEP (ukuvulwa nokuvala isango), ukhiye we-2 uvula ingxenye, ukhiye wesi-3 wenza umsebenzi we-VULA, ukhiye we-4 wenza umsebenzi we-CLOSE. Iyunithi yokulawula iyaphuma esigabeni sokufunda uma ungekho ukhiye omusha noma umyalo we-trasnmitter onikezwayo kumasekhondi angu-10.I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-6

Ukufunda ngokhiye ofihliwe wesidlulisi esivele sibambe ngekhanda
Ngokhiye ofihliwe wesidluliseli, kungenzeka ukuthi ungene esigabeni sokufunda ukuze ubambe ngekhanda okhiye abasha noma ama-transmitter amasha. Njengoba i-automation inganyakazi, ngosizo lwesiqeshana cindezela inkinobho efihliwe yesidlulisi esesivele sibambe ngekhanda, ukukhanya okukhanyayo kukhanyisa, manje sekungenzeka ukubamba ngekhanda okhiye abasha noma izithumeli.

Ukukhanselwa kwesidluliseli esisodwa

Faka isigaba sokufunda ngenkinobho ethi UP[+] noma ngokhiye ofihliwe wesidlulisi esibanjwe ngekhanda (bona 5.1 noma 5.2). Cindezela ngesikhathi esifanayo inkinobho efihliwe kanye nokhiye wokuqala wesidlulisi ofuna ukusikhansela. Ukukhanya okuphazimayo kubhanyaza izikhathi ezi-1 futhi kusibonisi kuzovelaI-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-7

Ukusetha i-wing stroke

  • Ukuze kusebenze kahle uhlelo, kubaluleke kakhulu ukusetshenziswa kwezitobhi zemishini ekuvuleni nasekuvaleni.

Izilungiselelo ezilula zokushaywa kwephiko (ipharamitha L51≠ p)

Xhuma kokuphumayo kwe-MOTOR 1 iphiko elishayayo. Faka isikhiya sikagesi esivele sikhona kulolu phiko. I-MOTOR 1 ihlale isebenza kuqala phakathi nesigaba sokuvula futhi okwesibili phakathi nesigaba sokuvala. Kule nqubo, kuyadingeka ukunikeza izikhundla ezilinganiselwe zamaphiko ngomyalo wesinyathelo ngesinyathelo (SS).

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-8

Ukuze kusebenze kahle uhlelo, kubaluleke kakhulu ukusetshenziswa kwezitobhi zemishini ekuvuleni nasekuvaleni.

Izilungiselelo ezithuthukisiwe ze-wing stroke (ipharamitha L51= p)

Xhuma kokuphumayo kwe-MOTOR 1 iphiko elishayayo. Faka isikhiya sikagesi esivele sikhona kulolu phiko. I-MOTOR 1 ihlale isebenza kuqala phakathi nesigaba sokuvula futhi okwesibili phakathi nesigaba sokuvala. Kule nqubo kuyadingeka futhi ukuhlinzeka ngezikhundla lapho ukwehla kokwehla kuqala ngomyalo wesinyathelo ngesinyathelo (SS).I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-9

Imenyu

Ifaka imenyu:
Ukufaka izilungiselelo zemenyu eyisisekelo qhubeka ucindezela inkinobho ethi MENU okungenani isekhondi elilodwa Ukufaka izilungiselelo zemenyu ethuthukisiwe qhubeka ucindezela inkinobho ethi MENU okungenani imizuzwana emihlanu Ukuzulazula kumenyu: Kuyenzeka ukusuka kwenye into uya kwenye usebenzisa UP. [+] e PHANSI[-] izinkinobho, Ukuze ushintshe ipharamitha qhubeka ucindezela inkinobho ethi MENU okungenani isekhondi elingu-1 kuze kube yilapho ipharamitha iqala ukucwayiza, ngakho khulula ukhiye. Sebenzisa izinkinobho PHEZULU[+] kanye NAPHANSI[-] ukuze ushintshe ipharamitha Ekugcineni qhubeka ucindezela u-MENU okungenani isekhondi elingu-1 kuze kube yilapho ipharamitha iyeka ukucwayiza ukuze ulondoloze ushintsho. Ukucindezela okusheshayo kokhiye wemenyu kwanele ukushiya imenyu.I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-10

Imenyu yezilungiselelo eziyisisekelo

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-11

Imenyu ethuthukisiwe

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-12I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-13 I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-14

Incazelo yemenyu

Imenyu yezilungiselelo eziyisisekelo

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-16 Isikhathi sokuvala kabusha ngokuzenzakalela
Iyasebenza lapho isango lisendaweni evuleke ngokuphelele, isango livaleka ngokuzenzakalelayo ngemva kwalokho I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-16imizuzwana. Kulesi sigaba isibonisi siyakhombisaI-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-15 ngodwi ocwayizayo, okuthi phakathi namasekhondi angu-10 wokugcina kuzothathelwa indawo ukubala phansi.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-17 Isikhathi sokuvala kabusha ngokuzenzakalela ngemva kokuthutha
Uma esigabeni sokuvula noma endaweni evulekile ngokuphelele ugongolo lwama-photocell lufihliwe futhi lukhululiwe, isango livala ngokuzenzakalelayo ngemuva. I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-15 imizuzwana lapho indawo evuleke ngokuphelele ifinyelelwa, Kulesi sigaba isibonisi sibonisa ngodwi ocwayizayo, ukuthi imizuzwana eyi-10 yokugcina izothathelwa indawo ukubala phansi.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-56Ukuzwela izithiyo
Lungisa ukuzwela kwesithiyo ukuze uqinisekise ukusebenza kahle kwesango, kufanele liyeke uma kunesithiyo kodwa futhi kufanele liqinisekise ukunyakaza okuphelele ezimweni ezimbi kakhulu (exp. Ubusika, ukuqina kwama-motors, njll). Ngemva kokulungiswa kwaleli pharamitha, kunconywa ukwenza amadokhumenti aphelele (ukuvula nokuvala) ngaphambi kokuzama ukuthola izithiyo.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-19I-torque yemoto
Lungisa i-torque ye-motor ukuqinisekisa ukusebenza kahle kwesango, kungenzeka ukulungisa i-percentagi-torque ephakathi kuka-10% kuya ku-100%. Ngemuva kokulungiswa kwalesi simiso, kunconywa ukwenza amadokhumenti aphelele (ukuvulwa nokuvala) ukuqinisekisa ukusebenza kahle kwesango.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-20  Imodi yokwehlisa ijubane
Iyunithi yokulawula inezinhlobo ezi-2 ezihlukene zokwehla kancane: okujwayelekile noma okunetorque ephezulu nesivinini, kumasango asindayo.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-21 Isinyathelo ngesinyathelo ukucushwa (SS)

  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-21= 0 Okuvamile (OP-ST-CL-ST-OP-ST…) Ukusebenza okujwayelekile kwesinyathelo ngesinyathelo. Ngesikhathi sokunyakaza, umyalo we-SS umisa isango.
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-21= 1 I-STOP Eshintshanayo (OP-ST-CL-OP-ST-CL…) Ukusebenza okushintshwayo ngokuthi STOP ngesikhathi sokuvula. Phakathi nesigaba sokuvula, umyalo we-SS umisa isango.
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-21= 2 Kuyashintshana (OP-CL-OP-CL…) Umsebenzisi akakwazi ukumisa isango ngesikhathi sokunyakaza ngomyalo we-SS. Umyalo we-SS ngesikhathi sokunyakaza uguqula ukunyakaza.
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-21= 3 I-Condominium – isibali sikhathi Umyalo we-SS uvula isango kuphela. Lapho isango livuliwe ngokuphelele, uma umyalo uphikelela iyunithi yokulawula izolinda kuze kuvulwe othintana naye ngaphambi kokuqala ukucushwa kokuvala kabusha okuzenzakalelayo (uma kunikwe amandla), omunye umyalo we-SS kulesi sigaba uzoqala kabusha ukubala phansi kokuvala okuzenzakalelayo.
  • = 4 I-Condominium ezivaleka kabusha ngokuzenzakalelayo Njenge-condominium – timer (iphuzu langaphambilini) kodwa ngesikhathi sokubala wehla umyalo we-SS uzovala isango.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-22Ngemva kokucima
Lapho iyunithi yokulawula ivuleka ngemuva kokucisha,

  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-22= 0 Akukho senzo – uma iyunithi yokulawula ivula isango inganyakazi kuze kube umyalo wokuqala, ukunyakaza kokuqala kuwukuvula kancane.
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-22= 1 Ukuvala– ukuvula iyunithi yokulawula kuzovala kancane.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-23Isiqalo esithambile
Ukunyakaza kuqala nge-torque encishisiwe, esetshenziswa emasangweni alula.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-24Ukubambezeleka kwephiko lesibili
Lesi yisilungiselelo sokubambezeleka kophiko lwesibili ukuze kuqinisekiswe ukusebenza kahle. Esigabeni sokuvala, iyunithi yokulawula yengeza imizuzwana emi-4 ukuze kuqinisekiswe ukuthi amaphiko awadluleli nasezimeni ezimbi kakhulu zokusebenza.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-25Ampamandla okwehlisa ijubane
Ngale parameter, kungenzeka ukulungisa i- ampumthamo wokwehlisa ijubane futhi ekugcineni uyicime (I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-25=0). Uma udinga okunembe kakhudlwana noma okuhlukile ukwehlisa ijubane phakathi kokuvula nokuvala kungenzeka ukusetha ipharamitha I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-25 on p (okuqondene nawe) nokwenza ukufunda okuthuthukile kokushaywa unhlangothi (5.2) okuhlinzeka futhi nokuqala kokwehla ngesikhathi sokufunda.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-26I-Antislip
Le parameter isetshenziswa uma i-motor ishelela, iyunithi yokulawula iyengeza I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-26 imizuzwana ukunyakaza ukuqinisekisa ukunyakaza okuphelele kwamaphiko futhi esimweni esibi kakhulu.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-27Inombolo yezinjini
Le parameter isetshenziselwa ukusetha inombolo yezinjini, imisebenzi yokufunda kanye nokusebenza kuzolungiswa kuye ngale parameter.

Imenyu ethuthukisiwe

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-28I-Bluetooth
Into yemenyu edingekayo ekuhlanganisweni kokuqala phakathi kwedivayisi ye-Android neyunithi yokulawula. Bheka Usizo lohlelo lokusebenza lwe-Android ngenqubo yokuxhuma.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-29Ibhuleki likagesi
Ukunyakaza okufushane okubuyela emuva ngetorque encishisiwe ukunciphisa inertia yesango. Umsebenzi wenziwa endaweni ngayinye yokuma kokunyakaza ngaphandle kokunyakaza okusheshayo ngemva kokungenelela kwemishini yokuphepha.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-30Ukusebenza kwe-photocell yokuvala PHOTO1 isuka endaweni evaliwe I-photocell evalayo inokusebenza okulandelayo

  • Ukuvala: ukuguqulwa okusheshayo kokunyakaza
  • Ukuvula kusuka endaweni emaphakathi: akukho ukungenelela
  • Ivula endaweni evaliwe:
    • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-30= 0 Isango alinyakazi uma ugongolo lwe-PHOTO1 lusikiwe
    • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-30= 1 Isango liyahamba ngenkathi ugongolo lwe-PHOTO1 lusikwa

.. Ukusebenza kokuvula i-photocell PHOTO2
I-photocell evulayo inokusebenza okulandelayo

  • Ukuvula: imisa ukunyakaza futhi ilinde kuze kukhululwe ugongolo, bese ihamba ngokuvula.
  • Iyavala:
    • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-31= 0 Imisa ukunyakaza futhi ilinde kuze kudedelwe ugongolo, bese ihamba ngokuvula
    • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-31= 1 Akukho ukungenelela

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-32Ukuhlolwa kwama-Photocell
Ivumela lo msebenzi, ngaphambi kokunyakaza ngakunye kuqale esangweni elimile, iyunithi yokulawula yenza ukuhlola okusebenzayo kwamaseli ezithombe. Ukuhlolwa ngeke kwenziwe uma kwenzeka ukunyakaza okusheshayo ngemva kokungenelela kwemishini yokuphepha. Landela isigaba 3.6 ukuze uthole ukuxhumana kwamaseli ezithombe.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-33 Uhlobo lomkhawulo wokuphepha
Iyunithi yokulawula ingasebenza nezinhlobo ezimbili ezihlukene zomkhawulo wokuphepha:

  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-33= 0 Imishini enokuxhumana okuvamise ukuvaleka
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-33= 1 Ukumelana no-8k2

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-34Imodi yokusebenza yomkhawulo wokuphepha.
Ukuvumela ukufakwa kwemiphetho yokuphepha kuzo zombili izinkomba zokunyakaza, ungakhetha imisebenzi emi-2 ehlukene:
• I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-34= 0 Ekuvaleni kuphela ngokuguquguquka okuphelele kokunyakaza
• I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-34= 1 Zombili izikhombisi-ndlela zokunyakaza, ukuma kanye nokuguquguquka okufushane ukukhulula isithiyo

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-57Ukuhlolwa konqenqema lokuphepha
Ukunika amandla lo msebenzi iyunithi yokulawula yenza ukuhlola okusebenzayo konqenqema lokuphepha. Lo msebenzi usetshenziswa uma unqenqema oluxhunywe kuyunithi yokulawula lunomshini wokuzihlola we-elekthronikhi (exp. unqenqema lomsakazo R.CO.O). Xhuma othintana naye wokuhlola wonqenqema ekunikezeni amandla kwesidlulisi samaseli ezithombe (isigaba 3.6) bese unika amandla ukuzihlola ngevolthi ephansi.tage 0Vdc (ngokuhambisana landela iziqondiso zemanuwali yomkhawulo wokuphepha).

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-35Ukuvula ingxenye
Ukuvula ingxenye kungenziwa kuphela kusukela ekuvaleni. Ipharamitha isetha ukuvuleka njengephesentitage yengqikithi yokushaywa kwephiko lokuqala.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-36 Isikhathi sokuvala ngokuzenzakalela kusukela ekuvuleni ingxenye
Iyasebenza uma isango lisesikhaleni esivulekile, isango lizivaleka ngemuva I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-36 imizuzwana. Kulesi sigaba, isibonisi sibonisa ngedeshi ecwayizayo, ukuthi phakathi nemizuzwana eyi-10 yokugcina izothathelwa indawo ukubala. I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-58

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-59 Imodi yokukhipha ukukhanya okubenyezelayo
Kungenzeka ukukhetha imisebenzi emi-2 ehlukene yokuphuma kokucwayiza:

  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-59= 0 Okukhiphayo kokucwayiza okungaguquki. Kuzodingeka ukuxhuma okokucwayiza okuzikhanyelayo (B.RO LIGHT 230 Vac)
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-59 = 1 Okuphumayo kokucwayiza kokukhanya. Kuzodingeka ukuxhuma i-fix light blinker (B.RO LIGHT FIX 230 Vac)

 I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-60 Isikhathi sangaphambi kokukhanya
Ukukhanyisa ngaphambili ngaphambi kokunyakaza ngakunye kuzo zombili izinkomba, I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-60. imizuzwana yokucwayiza kwangaphambili

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-38Ngesizotha izilungiselelo zokukhanya
Iyunithi yokulawula inemisebenzi emi-4 ehlukene yokukhanya okuhle:

  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-38 = 0 Isibani siyacisha ekupheleni komnyakazo ngemva I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-61 imizuzwana
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-38= 1 Isibani sicisha kuphela ngesango elivaliwe ngemuva I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-61imizuzwana
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-38= 2 ikhanyiselwe I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-61imizuzwana kusukela ekuqaleni kokunyakaza, ngaphandle kwesimo sesango (ukukhanya kungacisha ngaphambi kokuphela kokunyakaza)
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-38 = 3 Vula ilambu lesango – ilambu liyacisha ngokushesha lapho isango lifika endaweni evaliwe
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-38 = 4 ukukhanya kwesango elivuliwe ngokucwayiza okulingana:
    • ukuvula - ukucwayiza kancane
    • ukuvala - ukucwayiza ngokushesha
    • kuvuliwe - ukukhanya kuvuliwe
    • kuvaliwe - kuvaliwe ukukhanya
    • kumile - 2flash + ukulinda isikhathi eside + 2flash + ukulinda isikhathi eside +…
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-61 Ngenhlonipho isibali sikhathi sokukhanya Ngenhlonipho isibali-sikhathi sokukhanyisa ukukhanya

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-39 Deadman
Ngesikhathi semodi yokusebenza komuntu ofile, isango lihamba kuphela ngomyalo ongunaphakade. Imiyalo enikwe amandla ithi VULA futhi VALA. I-SS ne-PED akhutshaziwe. Ngesikhathi sokusebenza komuntu ofile konke ukunyakaza okuzenzakalelayo kuyacishwa, njengokuguquguquka okufushane noma okuphelele. Wonke amadivayisi okuphepha akhutshaziwe ngaphandle kwe-STOP.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-40Ukusetha umkhawulo wemijikelezo yesicelo sosizo
Kungenzeka ukusetha inani lemijikelezo ngaphambi kwesicelo sosizo. Uma umkhawulo usufinyelelwe imijikelezo elandelayo izokwenziwa ngokucwayiza okusheshayo (kuphela uma I-FPr kunikwe amandla)

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-41 Ukukhanya okuqhubekayo okukhanyayo kwesicelo sosizo
Kanye umkhawulo I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-40 kufinyelelwa ukukhanya okukhanyayo kuzocwayiza futhi isango livaliwe ukukhombisa isicelo sosizo. HA.0 Isando samanzi esigabeni sokuvula
Lokhu kusebenza kusetshenziselwa ukukhiya kagesi. Isango ngaphambi kokuvuleka liyavalwa maduze nje esitobhini umakhenikha evala ilokhi kagesi, ukuze kuqinisekiswe ukunqanyulwa okulungile. Ipharamitha isikhathi sokucindezela kusitobhi sikamishini ngaphambi kokuvula, silungiseka ukusuka ku-0.1 kuya ku-10 s.
Ukulandelana okwenziwe yiyunithi yokulawula ngaphambi kokuvula yilokhu okulandelayo:

  • ukuqaliswa kokuvimbela (kuphela uma I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-43 iyasebenza) yesikhiya sikagesi [1,5s]
  • ukusebenza kwemoto lapho kuvalwa ngetorque ephezulu. Ubude balesi sigaba bubekwe yipharamitha HA.0.
  • ukuguqulwa kwesikhombisi-ndlela ngenye imizuzwana emi-2 yokusebenza kwesikhiya sikagesi (kuphela uma I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-43 iyasebenza).

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-62 Isando samanzi esigabeni sokuvala
Lo msebenzi usetshenziswa ngokukhiya ugesi. Lapho isango lifinyelela esitobhini sokuvala sokuvala iyunithi yokulawula yenza ingcindezi enamandla, I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-62. imizuzwana ubude, ukuqinisekisa ukukhiya ingidi kagesi. (kuphela uma I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-43 iyasebenza)

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-63Isikhathi sokucindezela endaweni evaliwe yama-hydraulic motors
Lo msebenzi usetshenziselwa ukugcina umfutho we-hydraulic motors uphezulu, owenziwa kuphela ngesango elivaliwe, iyunithi yokulawula yenza iminithi elingu-1 lokuvala zonke. I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-63. umzuzu wokugcina ukucindezela okuphezulu kuma-motor kanye nendawo efanele evaliwe.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-43 Imodi yokukhiya ugesi

  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-43= 0 khubaza
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-43= 1 Ilokhi kagesi icushwa lapho i-automation yenza umnyakazo wokuvula.
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-43= 2 Ilokhi kagesi iyasebenza lapho i-automation yenza ukunyakaza kokuvula. Esigabeni sokuvula, icushwa ngokuphepha kusengaphambili kwamasekhondi angu-1.5.
  • I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-43= 3 Uma kusetshenziswa ilokhi kagesi kazibuthe, ihlala isebenza lapho isango livaliwe (ngaphandle uma injini icindezelekile endaweni evaliwe), khubaza lapho isango lingavaliwe.

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-64 Viewukumiswa kwendawo yenkumbulo yesidluliseli esisodwa
Ngento ekumenyu I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-64 kungenzeka view indawo yenkumbulo lapho isidlulisi sibanjwa ngekhanda. Ukuze wenze umsebenzi, hambisa ku I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-64 bese uqinisekisa ngokucindezela inkinobho MENU. Gcina ucindezelwe inkinobho yeMENU kuze kuvele isibonisi I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-44 bese udedela inkinobho.

Kuleli qophelo cindezela inkinobho yesidlulisi esibanjwe ngekhanda (ayenzi isebenze noma yimuphi umyalo). Isibonisi sibonisa:

  • indawo yenkumbulo imizuzwana emi-2, uma ibambe ngekhanda;
  • ezibhaliwe I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-45 imizuzwana emi-2, uma ingabanjwanga ngekhanda.

Ngemuva kwemizuzwana emi-2 isibonisi sibuyela esikrinini I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-44 futhi kuzokwazi ukwenza lo msebenzi ngomunye umthumeli. Ukuze uphume emsebenzini, cindezela inkinobho ethi MENU. Uma kungenjalo ngemva kwemizuzwana engu-15 ngaphandle kokudlulisela, iyunithi yokulawula iyaphuma emsebenzini futhi ibonise okubhaliwe I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-46

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-65Ukukhanselwa kwesidluliseli esisodwa
Ngento ekumenyu I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-65. kungenzeka ukususa isidlulisi esisodwa kumemori.
Ukuze wenze umsebenzi, hambisa ku I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-65. bese uqinisekisa ngokucindezela inkinobho MENU. Qhubeka ucindezela inkinobho ethi MENU kuze kube yilapho isibonisi siveza u-0, bese ukhulula inkinobho. Khetha indawo yememori yesithumeli. Cindezela futhi uqhubeke ucindezela inkinobho ethi MENU kuze kuvele isibonisi,I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-47 bese udedela inkinobho.

Ukuze uphume emsebenzini, cindezela inkinobho MENU. Uma isibonisi sibonisa okubhaliwe, I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-48 kunezinkinga ngememori (ngokwesiboneloampindawo engenalutho noma inkumbulo enqanyuliwe).

I-dE.F. Buyisela izilungiselelo ezizenzakalelayo
Ngento yemenyu I-dE.F. kungenzeka ukubuyisela izilungiselelo ezizenzakalelayo zeyunithi yokulawula. Ukusetha kabusha kuzobuyisela wonke amapharamitha esisekelo nemenyu ethuthukisiwe kodwa akuguquli imivimbo efundiwe, izikhombisi-ndlela zamamotho kanye nezidlulisi. Dlulela ku I-dE.F. bese uqhubeka ucindezela inkinobho ethi MENU kuze kube isibonisi siveza u-0, bese ukhulula inkinobho. Cindezela futhi futhi uqhubeke ucindezela inkinobho ethi MENU, futhi isibonisi sizobonisa ukubala wehla I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-66,ungayikhiphi inkinobho kuze kuvele isibonisi I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-49

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-50Ukusula wonke ama-transmitters
Ngento yemenyu I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-50. kungenzeka ukusula wonke ama-transmitter afundiwe. Dlulela kuI-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-50 bese uqhubeka ucindezela inkinobho ethi MENU kuze kube isibonisi siveza 0, khulula inkinobho. Cindezela futhi bese ugcine ucindezela inkinobho ethi MENU, isibonisi sizobonisa ukubala wehla I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-66,ungayikhiphi inkinobho kuze kuvele isibonisiI-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-49

Isimo seyunithi yokubonisa nokulawula

Ukusebenza okuvamile

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-51I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-52

Amaphutha

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-53

Ukubonakala kwephutha kusibonisi kuyaqhubeka kuze kukhishwe omunye umyalo

Okokufaka kwe-LED namadivayisi okuphepha

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-54

Izici zobuchwepheshe

I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-67

Izimoto

Ukusebenza okulungile kuqinisekiswa kuphela uma kwenzeka ama-Allmatic motors. Ukuze uthole ukuphepha okukhulu, kuphakanyiswa ukuthi ufake i-fuse (T 3,15A) ochungechungeni kokujwayelekile kwawo womabili amamotho. Iyatholakala ikhithi enezintambo zangaphambili (ongakukhetha) engafakwa njengoba kukhonjisiwe emdwebeni ongezansi.I-ALLMATIC-CONTROL-UNIT-BIOS2-Programmable-Control-Board-fig-55

I-WEEE - Ulwazi lwabasebenzisi: Uma uphawu lomgqomo oweqiwe luvela empahleni noma ephaketheni, lokhu kusho ukuthi umkhiqizo akumele uhlanganiswe nenye imfucuza ejwayelekile ekupheleni kwesikhathi sokusebenza kwawo. Umsebenzisi kufanele athathe umkhiqizo osugugile awuyise esikhungweni sikadoti esihlungiwe, noma awubuyisele kumthengisi lapho uthenga omusha. Imikhiqizo ethengiswayo ingathunyelwa mahhala (ngaphandle kwesibopho esisha sokuthenga) kubathengisi abanendawo yokuthengisa okungenani engu-400 m2, uma ikala ngaphansi kuka-25 cm. Ukuqoqwa kwemfucuza ehlungwe kahle ukuze kulahlwe okobungani nemvelo komshini osetshenzisiwe, noma ukugaywa kabusha kwawo okwalandela, kusiza ukugwema imiphumela engemihle engaba khona endaweni ezungezile nempilo yabantu futhi kukhuthaze ukuphinda kusetshenziswe kanye/noma ukugaywa kabusha kwezinto zokwakha.

QINISEKISA

Ngokuhambisana nomthetho, isiqinisekiso somkhiqizi sisebenza kusukela ngosuku luka-stamped emkhiqizweni futhi ikhawulelwe ekulungiseni noma ekushintsheni mahhala izingxenye ezamukelwe umenzi njengezinephutha ngenxa yezinto ezisezingeni eliphansi noma amaphutha okukhiqiza. Isiqinisekiso asibandakanyi umonakalo noma iziphambeko ezibangelwa ama-ejenti angaphandle, ukunakekelwa okungalungile, ukulayishwa ngokweqile, ukuguga kwemvelo, ukukhetha komkhiqizo okungalungile, amaphutha okuhlanganisa, nanoma iyiphi enye imbangela engenakugwenywa kumkhiqizi. Imikhiqizo esetshenziswe kabi ngeke iqinisekiswe noma ilungiswe. Ukucaciswa okuphrintiwe kuyinkomba kuphela. Umkhiqizi akamukeli noma yimuphi umthwalo wemfanelo wokunciphisa ububanzi noma ukungasebenzi kahle okubangelwa ukuphazamiseka kwemvelo. Isibopho somkhiqizi ngomonakalo odalwe kubantu ngenxa yezingozi zanoma iluphi uhlobo oludalwe imikhiqizo yethu enesici, yilezo zibopho kuphela eziza ngaphansi komthetho wase-Italy.

Amadokhumenti / Izinsiza

ALLMATIC CONTROL UNIT BIOS2 Programmable Control Board [pdf] Incwadi Yeziqondiso
CONTROL UNIT BIOS2 Ibhodi Lokulawula Elihlelekayo, CONTROL UNIT BIOS2, Ibhodi Lokulawula Elihlelekayo, Ibhodi Lokulawula, Ibhodi

Izithenjwa

Okuthunyelwe Okuhlobene

Shiya amazwana

Ikheli lakho le-imeyili ngeke lishicilelwe. Izinkambu ezidingekayo zimakiwe *