I-AcreL 259 WHD Temperature and Humidity Controller
Ulwazi Lomkhiqizo
I-WHD Temperature & Humidity Controller yakhelwe ukulungisa nokulawula izinga lokushisa kanye nomswakama ngevolthi ephezulu.tagama-switchgear, amatheminali amabhokisi, amaphaneli enethiwekhi ayindandatho, iziteshi ezishintshashintshayo zamabhokisi, nezinye izinto zokusebenza. Ivikela ngempumelelo okokusebenza emaphutheni abangelwa amazinga okushisa aphezulu, i-creepage, i-flashover, umswakama, noma ukufingqa. Lo mkhiqizo uhlangabezana nezidingo ze-GB/T 15309-1994.
Isilawuli siqukethe i-transmitter, isilawuli, ne-heater noma ifeni. Ingalungiselelwa ngemisebenzi yokulawula ehlukene futhi inezinketho zokuxhumana kwe-RS485, okukhiphayo okwethusayo, nokudlulisa. I-WHD Temperature & Humidity Controller itholakala ngosayizi abahlukene nezinhlobo zamaphaneli. Amapharamitha wobuchwepheshe afaka uhla lokulinganisa, ukunemba, okukhiphayo, isethi yohlu lwamapharamitha okulawula, umthamo wokuxhumana okukhiphayo, imbobo yokuxhumana, amandla asizayo, ivolumutage ukusetshenziswa, ukwahlukanisa ukumelana, amandla-frequency ukumelana voltage, isilinganiso sesikhathi somsebenzi ngaphandle kokumiswa, nezimo zokusebenza.
Imiyalo yokusetshenziswa komkhiqizo
- Qinisekisa ukuthi isilawuli sifakwe endaweni efanele lapho singaqapha kahle izinga lokushisa nomswakama.
- Xhuma izinga lokushisa elifanele nezinzwa zomswakama kusilawuli ngokusekelwe kumodeli (WHD48, WHD72, WHD20R, noma WHD46) esetshenziswayo. Bheka kumanuwali yomsebenzisi ngenombolo ethile yezinzwa ezivunyelwe kumodeli ngayinye.
- Uma kudingeka, xhuma i-heater kanye nefeni koxhumana nabo bokulawula okukhiphayo kwesilawuli. I-heater isetshenziselwa ukukhuphuka kwezinga lokushisa noma ukususwa komswakama, kuyilapho ifeni isetshenziselwa ukwehlisa izinga lokushisa.
- Uma kusebenza, lungiselela imisebenzi eyisiza efana nokuxhumana kwe-RS485, okukhiphayo okuthusayo, kanye nokudlulisa ngokusekelwe kuzimfuneko zohlelo lwakho lokusebenza.
- Setha amapharamitha okulawula oyifunayo ngezinga lokushisa kanye nomswakama usebenzisa iphaneli yokulawula noma isixhumi esibonakalayo esihlinzekiwe.
- Qinisekisa ukuthi isilawuli sinokunikezwa kwamandla okuzinzile ngaphakathi kwevolthi eshiwotage ububanzi. Hlola ukusetshenziswa kwamandla futhi uqiniseke ukuthi kungaphakathi kwemikhawulo eyamukelekayo.
- Qinisekisa ukumelana ne-insulation kanye ne-power-frequency ukumelana ne-voltage ukuqinisekisa ukuphepha kukagesi.
- Gada ukusebenza kwesilawuli futhi ulungise izilungiselelo njengoba kudingeka ukuze ugcine izinga lokushisa elifunekayo kanye namaleveli womswakamo.
Isimemezelo
Ayikho ingxenye yalolu shicilelo okumele ikhiqizwe kabusha, igcinwe ohlelweni lokuthola kabusha, noma idluliselwe nganoma iyiphi indlela nganoma iyiphi indlela, nge-electronic, mechanical photocopying, recording, noma ngenye indlela ngaphandle kwemvume yangaphambili ye-AcreL. Wonke Amalungelo Agodliwe. Le nkampani igodla amandla okubuyekeza imininingwane yomkhiqizo echazwe kuleli bhukwana, ngaphandle kwesaziso. Ngaphambi koku-oda, sicela uxhumane nomenzeli wendawo ukuze uthole imininingwane yakamuva yomkhiqizo.
Okujwayelekile
Isilawuli samazinga okushisa nomswakama sifanele ukulungiswa nokulawulwa kwezinga lokushisa nomswakama kumishini ye-voltage ephezulu.tagi-switchgear, i-terminal box, i-ring network panel, i-box transformer substation njll. Ingakwazi ukuvikela ngempumelelo okokusebenza okufanelekile emaphutheni abangelwa izinga lokushisa eliphansi kakhulu noma eliphezulu, i-creepage noma i-flashover njll.kumswakama noma ukujiya. Le mikhiqizo ihlangabezana nezidingo ze-GB/T 15309-1994.
Isimiso sokusebenza
Isilawuli sezinga lokushisa kanye nomswakama ikakhulukazi siqukethe izingxenye ezintathu zesidlulisi, isilawuli, i-heater (noma ifeni njll.), umgomo waso wokusebenza uboniswa njengokulandelayo:
Umlayezo wezinga lokushisa nomswakama osebhokisini utholwa inzwa futhi uhlaziywe yisilawuli: Uma izinga lokushisa lemvelo, umswakama ufinyelela kunani lokusetha ngaphambilini noma udlule inani lokusetha ngaphambilini, isilawuli sinikeza isignali ehlobene koxhumana nabo be-relay, bese I-heater (noma ifeni) inamandla futhi isebenza ekushiseni kokuqeda umswakama; Ngemuva kwezinga lokushisa lemvelo, umswakama ungaphansi kwenani lokusetha ngaphambilini, i-heater (noma ifeni) inikezwa amandla futhi iyeke ukusebenza. Ngaphezu kwemisebenzi yawo eyisisekelo, umkhiqizo othize onohlobo oluhlukile unemisebenzi yesibili njengokuphuma okuthusayo kokuphulwa kwentambo, ukuxhumana, ukushisisa ngempoqo njll.
Thayipha incazelo
Qaphela
- Inombolo 0f izinga lokushisa, umswakama(noma izinga lokushisa) inzwa ezoxhunywa ne-WHD48, WHD72. I-WHD20R, i-WHD46 ifika ku-1,2, 3 ngokulandelana;
- Wonke umdlalo wezinzwa othintana nokulawula okukhiphayo okubili (okungagciniwe), okuxhunywe ne-heater kanye nefeni ngokulandelana, i-heater isetshenziselwa ukukhuphuka kwezinga lokushisa noma ukususa umswakama, ifeni isetshenziselwa ukwehlisa izinga lokushisa;
- Umsebenzi osizayo we-WHD46:ukuxhumana kwe-R$485, umsebenzi wokuphuma othusayo kanye nomsebenzi wokudlulisa. Okukodwa kuphela okungakhethwa.
- Umsebenzi osizayo we-WHD48:RS485 ukuxhumana.
- Umsebenzi osizayo we-WHD72:Umsebenzi okhiphayo othusayo,ukuxhumana kwe-RS485 nomsebenzi wokudlulisa. Okubili kokugcina kungakhethwa kuphela.
- Umsebenzi osizayo we-WHD2OR:ukuxhumana kwe-RS485 kanye nomsebenzi wokuphuma othusayo. Kokubili kungakhethwa ngesikhathi esisodwa.
- – C” yokuxhumana,” -J” ngokwethusa,” -M” yokudlulisa.
- Intambo exhumayo phakathi kwenzwa nesilawuli kufanele isebenzise ikhebula elivikelwe elinezisekelo ezine. Futhi ubude bayo obukhulu akumele budlule ama-20 m.
Ipharamitha yobuchwepheshe
| Ipharamitha yobuchwepheshe | Inani | |||
|
Ibanga lokulinganisa |
Izinga lokushisa | -40.0℃～99.9℃ | ||
| Umswakama | 0% RH - 99% RH | |||
|
Ukunemba |
Izinga lokushisa | ±1℃ | ||
| Umswakama | ± 5% RH | |||
| Idlulisela okukhiphayo | I-DC 4～20mA 或 DC 0～20mA | |||
|
Setha ububanzi bepharamitha yokulawula |
Ukushisisa for
Izinga lokushisa liyakhuphuka |
-40.0℃～40.0℃ |
||
| Ukuvuthela
izinga lokushisa liyancipha |
0.0℃～99.9℃ |
|||
| Ukulawula umswakama | 20% RH - 90% RH | |||
| umthamo wokuxhumana okukhiphayo | 5A/AC250V | |||
| Qala/misa igebe | 5 | |||
| Imbobo yokuxhumana | RS485,MODBUS(RTU)协议 | |||
|
Amandla asizayo |
Voltage |
I-AC 85–265V
I-DC 100 ~ 350V |
||
|
Ukusetshenziswa |
Ukusetshenziswa kwamandla okuyisisekelo(≤0.8w);
ukusetshenziswa kwamandla okudlulisa (isiteshi ngasinye≤0.7w) |
|||
| Ukumelana ne-insulation | ≥100MΩ | |
|
amandla-frequency ukumelana voltage |
amandla anegobolondo, izingxenye zensimbi ezithintekayo/
amandla nezinye i-terminal group 2kV/1min(AC,RMS) |
|
| isilinganiso sesikhathi somsebenzi ngaphandle kokumiswa | ≥50000h | |
|
Isimo sokusebenza (isilawuli) |
Izinga lokushisa | -20℃～+60℃ |
| Umswakama | ≤95%RH, ngaphandle kokujiya kanye negesi egqwalayo | |
| Ukuphakama | ≤2500 m | |
Qala/misa igebe: Enqubweni yokulawula, engxenyeni yokwenza (i-heater noma ifeni), umehluko phakathi kwezinga lokushisa lokuqala(umswakama) kanye nezinga lokushisa elimisiwe (umswakama).
Ukucaciswa komkhiqizo nemisebenzi
Uhlobo lwe-WHD48 olunomsebenzi osizayo:ukuxhumana kwesignali”-C”
| Uhlobo | Umsebenzi | Inzwa (ama-PC) | Imodi yokukhweza | Uhlaka, usayizi |
|
WHD48-11 |
Izinga lokushisa lesiteshi esisodwa, ukulawula umswakama |
WH-3(1) |
I-Catout eshumekiwe: 45×45 |
 |
|
WHD48-22 |
Izinga lokushisa leziteshi ezimbili, ukulawula umswakama |
WH-3(1) WH-3T(1) |
Uhlobo lwe-WHD46 olunomsebenzi osizayo:i-alamu yephutha”-J”,ukuxhumana kwesignali”-C”,ukudlulisa”-M”
| Uhlobo | Umsebenzi | Inzwa (ama-PC) | Imodi yokukhweza | Uhlaka, usayizi |
|
WHD46-11 |
Izinga lokushisa lesiteshi esisodwa,
ukulawula umswakama |
WH-3(1) | I-Catout eshumekiwe: 116×56 |  |
|
WHD46-22 |
Izinga lokushisa leziteshi ezimbili,
ukulawula umswakama |
WH-3(2) | ||
| WHD46-33 | WH-3(3) |
Uhlobo lwe-WHD72 olunomsebenzi osizayo:i-alamu yephutha”-J”,ukuxhumana kwesignali”-C”,ukudlulisa”-M”
| Uhlobo | Umsebenzi | Inzwa (ama-PC) | Imodi yokukhweza | Uhlaka, usayizi |
| WHD72-11 | Izinga lokushisa lesiteshi esisodwa, ukulawula umswakama | WH-3(1) | I-Catout eshumekiwe: 67×67 |  |
| WHD72-22 | Izinga lokushisa leziteshi ezimbili, ukulawula umswakama | WH-3(2) |
Uhlobo lwe-WHD20R olunomsebenzi osizayo:i-alamu yephutha”-J” ,ukuxhumana kwesignali”-C”, kokubili kuyakhethwa
| Uhlobo | Umsebenzi | I-Sensr PC | Imodi yokukhweza | Uhlaka, usayizi |
|
I-WHD20R-11 |
Izinga lokushisa lesiteshi esisodwa, ukulawula umswakama | WH-3(1) | umhlahlandlela wesitimela uhlobo: DIN35mm |  |
|
I-WHD20R-22 |
Izinga lokushisa leziteshi ezimbili, ukulawula umswakama | WH-3(2) |
Imodi ye-wiring
Uhlobo lwe-WHD48
Uhlobo lwe-WHD72
Uhlobo lwe-WHD20R
Uhlobo lwe-WHD46
Umuntu wakudalaampI-wiring yengxenye yokuxhumana iboniswe ngezansi:
- Indlela elungile yokufaka izintambo: isihlangu sekhebula lokuxhumana sixhunywe phansi.
- Kunconywa ukuthi wengeze i-resistor efanayo phakathi kuka-A no-B wemitha yokugcina, futhi ububanzi bokumelana bungu-120 Ω-10KΩ.
Imanuwali yokusebenza komkhiqizo
Khombisa isingeniso
Umdwebo ongaphambili
Incazelo yenganekwane
| Cha. | Igama | Isimo | Incazelo |
|
1 |
lokushisa Area
Temp.indawo |
XX.X℃ |
Bonisa inani lamanje lokushisa elikalwe,ububanzi:-40.0℃～
99.9℃ Bonisa imenyu nedatha yohlelo lokuchofoza ukhiye |
| 2 | Iziteshi | X | Bonisa iziteshi ezikalwa manje,ububanzi:1～3 |
|
3 |
umswakama Indawo
Indawo yomswakama |
XX% |
Bonisa inani lomswakamo elikalwe manje,ububanzi:20%～90% |
|
4 |
Isimo sokusebenza |
Inkomba
ukukhanya |
Isimo sokusebenza esingu-1,2,3,iziteshi,ukushisisa (HEAT),
Ukuvuthela (FAN),iphutha lokushisisa (BREAK) |
| 5 | SET | Iyacindezela | Ukukhetha umsebenzi wokusebenza, setha ukuhlela |
|
6 |
Ukhiye wokuqondisa kwesokunxele |
Iyacindezela | Bheka idatha noma ushintshe idatha |
| Gcina
Iyacindezela |
Qhubeka Ucindezela ukhiye cishe imizuzwana emi-3, zonke iziteshi ziyashisisa |
||
|
7 |
Ukhiye wokuqondisa kwesokudla |
Iyacindezela | Bheka idatha noma ushintshe idatha |
| Gcina
Iyacindezela |
Qhubeka Ucindezela inkinobho cishe imizuzwana emi-3, wonke amashaneli ayafutha |
||
| 8 | FAKA ukhiye | Iyacindezela | Qinisekisa umsebenzi noma uye kumenyu elandelayo |
Isistimu inikwe amandla
- Ngemva kokufakwa kwezintambo ngendlela efanele ngokokubamba, vula amandla bese ungena esimweni sokulinganisa.
Isimo sokusebenza
Isilinganiso
- Ngaphansi kwesimo sokulinganisa, Indawo 1, 2, 3 isibonisi okwamanje: isiteshi sokulinganisa nenani lokushisa, inani lomswakamo, inani lokushisa, inani lomswakamo elijikelezayo nokuboniswa kwamashaneli amathathu enzwa.
Lawula
Lapho inani lokushisa kwemvelo noma inani lomswakamo lanelisa isimo sokusethwa kusengaphambili , ukuqala i-heater noma ifenisha, kuyilapho izibani zezinkomba ezihambisanayo (Indawo4) , lapho i-heater yehluleka, isebenza ngaphandle kwesimo esivamile sokusebenza, inkomba ehambisanayo yezibani zamaphutha okushisa. ukunikeza okwesabisayo.
Ukuhlolwa kokulawula
- Ngaphansi kwesimo esivamile sokusebenza, bamba ukucindezela ukhiye wokuqondisa kwesokunxele cishe imizuzwana emi-3, wonke amashaneli avunyelwe ashisayo; bamba ngokucindezela inkinobho ekhomba kwesokudla phezu kwamasekhondi angu-3, wonke amashaneli avunyelwe ayavuthela.
I-alamu
- Lapho i-heater yehluleka, isebenza ngaphandle kwesimo esivamile sokusebenza, inkomba ehambisanayo yezibani zokushisa-iphutha ukunikeza okwesabisayo.
- lapho izinga lokushisa lidlula inani elibekiwe, idatha yesiteshi esihambisanayo iyabaneka. Setha kabusha lapho imitha ngokwayo yehluleka.
Imodi yokusetha isistimu
Imodi yokusetha yesistimu yokungena/yophuma
- Ngaphansi kwesimo esivamile sokusebenza, bamba ucindezela ukhiye we-SET cishe imizuzwana emi-3, faka imodi yokuhlela uhlelo, shaya okuthi ENTER bese ufaka amagama okudlula, inani elimisiwe lokuletha njengo-0000, uma amagama okudlula elungile (bonisa YEBO ), faka kokuyinhloko. imenyu ngokuzenzakalelayo.
- Ngemva kokungena kumenyu enkulu , Isibonisi seNdawo 1 “CH1”, cindezela okuthi ENTER, faka ukulungiselelwa kwepharamitha yokusebenza yesiteshi 1, cindezela ukhiye wesokunxele/kwesokudla ukuze ushintshele kwenye imenyu enezinga elifanayo, le menyu yezinga ino-“CH2”, “CH3”, “COMM “,”DISP”，”CTRL”，”VERn”,imisa ipharamitha esebenzayo yesiteshi 2, isiteshi 3,ukuxhumana, imodi yokubonisa, ukubheka inguqulo yesofthiwe ngokulandelana.
Ukusetha amapharamitha wesiteshi
Inqubo yokusetha ipharamitha ye-CH1, CH2,CH3 yinto eyodwa futhi efanayo. Ukuthatha i-CH1 njengesibample , ukuchaza ngokucacile: Ngemva kokusetha uhlelo lokungena, imenyu nokuboniswa kwedatha kuNdawo 1, ngemva kokusetha isiteshi sokungena, Inombolo yesi-2 yokubonisa ukulandelana kwesiteshi. Bonisa ngaphambi kokungena.CH1:
| Example | Incazelo | |
| 1 | I-CH1 | Chofoza kanye okuthi ENTER, faka ukulungiselelwa kwepharamitha yesiteshi 1 |
| 2 | Akunalutho |
Chofoza kanye okuthi FAKA isibonisi ngendlela elandelayo:
| Example | Incazelo | |
|
1 |
ON |
Vumela isiteshi 1, ukhethe ukhiye wesobunxele/kwesokudla ukuze "uvule"/"cime", chofoza okuthi ENTER ukuze uqinisekise |
|
2 |
1 |
Isilungiselelo samanje yisiteshi sokuqala |
Ukukhetha “kuvuliwe”，Chofoza okukodwa FAKA isibonisi kanje
| Example | Incazelo | |
|
1 |
H.omile |
Chofoza kanye okuthi ENTER ukuze ungene, usetha inani lomswakamo lokuqala inqubo yokushisisa nokukhipha umswakama |
|
2 |
1 |
Isilungiselelo samanje yisiteshi sokuqala |
Chofoza kanye okuthi FAKA isibonisi ngendlela elandelayo
| Example | Incazelo | |
|
1 |
85 |
Chofoza kanye ukhiye wesobunxele/kwesokudla ukuze ubuyekeze, bamba ukucindezela ukuze ukhule/unciphise ngokushesha, chofoza okuthi FAKA ukuze uqinisekise |
|
2 |
1 |
Isilungiselelo samanje yisiteshi sokuqala |
Chofoza kanye okuthi FAKA isibonisi ngendlela elandelayo
| Example | Incazelo | |
|
1 |
UKUSHISA |
Chofoza kanye okuthi ENTER ukuze ungene, usetha inani lokushisa lokuqala inqubo yokushisisa nokukhuphuka kwezinga lokushisa |
|
2 |
1 |
Isilungiselelo samanje yisiteshi sokuqala |
Chofoza kanye okuthi FAKA isibonisi ngendlela elandelayo
| Example | Incazelo | |
|
1 |
5.0 |
Chofoza kanye ukhiye wesobunxele/kwesokudla ukuze ubuyekeze, bamba ukucindezela ukuze ukhule/unciphise ngokushesha, chofoza okuthi FAKA ukuze uqinisekise |
|
2 |
1 |
Isilungiselelo samanje yisiteshi sokuqala |
Chofoza kanye okuthi FAKA isibonisi ngendlela elandelayo
| Example | Incazelo | |
|
1 |
I-ALM.H |
Chofoza kanye okuthi ENTER , ukusetha i-alamu yephutha le-ifopen |
|
2 |
1 |
Isilungiselelo samanje yisiteshi sokuqala |
Chofoza kanye okuthi FAKA isibonisi ngendlela elandelayo
| Example | Incazelo | |
|
1 |
VALIWE |
ukukhetha ukhiye wesokunxele/wesokudla ukuze "kuvule"/"cime", chofoza u-ENTER ukuze uqinisekise |
|
2 |
1 |
Isilungiselelo samanje yisiteshi sokuqala |
Chofoza kanye okuthi FAKA isibonisi ngendlela elandelayo
| Example | Incazelo | |
|
1 |
UMlandeli.C |
Chofoza kanye okuthi ENTER , kusetha inani lokushisa ukuze uqale ukwehlisa izinga lokushisa elivunguzayo |
|
2 |
1 |
Isilungiselelo samanje yisiteshi sokuqala |
Chofoza kanye okuthi FAKA isibonisi ngendlela elandelayo
| Example | Incazelo | |
|
1 |
40.0 |
Chofoza kanye ukhiye wesobunxele/kwesokudla ukuze ubuyekeze, bamba ukucindezela ukuze ukhule/unciphise ngokushesha, chofoza okuthi FAKA ukuze uqinisekise |
|
2 |
1 |
Isilungiselelo samanje yisiteshi sokuqala |
Chofoza kanye okuthi FAKA isibonisi ngendlela elandelayo
| Example | Incazelo | |
|
1 |
HYS.H |
Chofoza kanye okuthi ENTER ukuze ungene, usetha inani le-hysteresis lokushisisa ukuze kususwe umswakama |
|
2 |
5 |
Chofoza kanye ukhiye wesokunxele/kwesokudla ukuze ubuyekeze , chofoza okuthi FAKA ukuze uqinisekise |
|
1 |
I-HYS.d |
Chofoza kanye okuthi ENTER ukuze ungene, usetha inani le-hysteresis lokushisisa ukuze kususwe umswakama |
|
2 |
5 |
Chofoza kanye ukhiye wesokunxele/kwesokudla ukuze ubuyekeze , chofoza okuthi FAKA ukuze uqinisekise |
|
1 |
I-HYS.U |
Chofoza kanye okuthi ENTER ukuze ungene, usetha inani le-hysteresis lokushisisa ukuze kususwe umswakama |
|
2 |
5 |
Chofoza kanye ukhiye wesokunxele/kwesokudla ukuze ubuyekeze , chofoza okuthi FAKA ukuze uqinisekise |
Chofoza kanye okuthi Faka, buyisela imenyu enkulu, sebenzisa ukhiye wesobunxele/kwesokudla ukuze ukhethe enye imenyu eyinhloko futhi usethe into ongayikhetha. Ukuxhumana “I-COMM” ingasetha ikheli Lendawo ( 1～247) kanye nenani lesilinganiso se-baud yokuxhumana (1200, 2400,4800,9600,19200) . Imodi yokubonisa"dISP" isetshenziselwa ukusetha amashaneli amathathu: isikhawu ekubukweni kokulinganisa okujikelezayo; ukujikeleza okuvaliwe noma isikhawu sama-2s, 4s, 6s, 8s. Ukuma okungahleliwe kwe-AI kumenyu enkulu, chofoza okukodwa okuthi SET ukuze ukhethe isitoreji noma cha bese uphuma ekusethweni kwesistimu, bese ubuyisela emuva imodi evamile yokusebenza.
Setha iphasiwedi yesistimu
- Cindezela okuthi SET bese u-ENTER ngesikhathi esisodwa cishe imizuzwana emithathu, bonisa: “CodE”, Chofoza kanye okuthi ENTER ukuze ungene, thayipha iphasiwedi yesistimu yamanje. Chofoza kanye okuthi ENTER ukuze uqinisekise iphasiwedi ethayiphiwe, igama eliyimfihlo elibhalwe ukuthi “yebo”, bese ushintshela ku-“n.Cod” ngokuzenzakalelayo, ukufakwa ngokuchofoza kanye ukuze uthayiphe iphasiwedi entsha, cindezela u-ENTER ukuze ukhethe isitoreji noma cha, bese uphuma.
- Kumasethingi angahleliwe, uma phakathi kwemizuzu engu-1, kungekho khiye osebenzayo ocindezelwayo, isistimu ibuyela esimweni sokulinganisa ngokuzenzakalelayo isilungiselelo asigcinwa.
Umdwebo wokugeleza koHlelo lomsebenzisi
| Umlingiswa | Incazelo | Umlingiswa | Incazelo |
| Inqubekela phambili | Finyelela ukuhlela | CoMM | Ukuxhumana |
| IkhodiE | Iphasiwedi | Addr | Ikheli |
| xxx | Umfanekiso nabanye | Bhude | Isilinganiso se-Baud |
| CH1/CH2/CH3 | Finyelela iziteshi 1/2/3 | I-diSP | Isilungiselelo sokubonisa |
| H.omile | Ukushisa ukususa umswakama | d.Cyc | Isibonisi esiyindilinga |
| UKUSHISA | Ukushisa ukuze kukhuphuke izinga lokushisa | I-CdL | Ubude bokuxhumana
isikhawu sefrequency |
| I-ALM.H | I-alamu ye-heater yocingo oluphukile | I-VERn | Inombolo yenguqulo yesofthiwe |
| Umlandeli.C | Vuthela ukuze unciphise izinga lokushisa | n.Ikhodi | Ithayipha iphasiwedi |
| Hys.H | Inani le-hysteresis lokushisisa okufanele lisuswe
umswakama |
GCINA | Isitoreji |
| Hys.d | Inani le-hysteresis lokushisisa lizokhuphuka
izinga lokushisa |
i-ruPt | Ukwehluleka kwenzwa |
| Hys.U | Inani le-hysteresis lokushaya elizoncishiswa
izinga lokushisa |
I-SEL | ukukhetha okukhiphayo okufanelekile |
| tr.1/tr.2 | Letha izinhlelo zokufinyelela | tr.Lo | izinhlelo ziphansi |
| tr.Sawubona | ukuhlela okusezingeni eliphezulu | ||
| I-CTRL | Ukusetha okuphoqiwe kokushisisa/ukufutha | x.xH | Isikhathi , 0.0H: Qhubeka |
Imanuwali yokuxhumana
Ukuxhumana
Lesi sahluko sichaza ikakhulukazi indlela yokusebenzisa isofthiwe ukusebenzisa lolu chungechunge imitha ngokuxhumana esibonakalayo. Kudingeka ukuthi uthole ulwazi lwephrothokholi ye-MODBUS futhi ube nokuqonda okujwayelekile kokusebenza kwemitha kanye nokusetshenziswa kwayo ngemva kokufunda okunye okuqukethwe yile manuwali. Okuqukethwe kulesi sahluko kuhlanganisa: ukwethulwa kafushane kwephrothokholi ye-MODBUS, incazelo eningiliziwe yefomethi yesicelo sokuxhumana, imininingwane yesicelo yethebula lemitha kanye nepharamitha yekheli.
Ukuxhumana kwe-MODUS
I-WHD Series Intelligent Temperature & Humidity Controller. Iphrothokholi ye-MODBUS ichaza ikhodi yokukhokha enemininingwane, ukulandelana kwedatha nokunye okuqukethwe okudingekayo koshintsho oluthile lwedatha. Iphrothokholi ye-MODBUS isebenzisa imodi yokuxhumana eyisigamu se-duplex ocingweni olulodwa lokuxhumana. Lokho kusho amasiginali wokudluliswa kwentambo okuhlukile ngendlela ephambene. Okokuqala, isignali yekhompuyutha engusokhaya ifuna ikheli leyunithi yetheminali ekhethekile, bese iyunithi yetheminali ithumela isignali esabelayo edluliswa kukhompyutha yokusingatha ngendlela ephambene. Iphrothokholi ye-MODBUS ivumela kuphela ukuxhumana phakathi kwe-mainframe(i-PC, i-PLC njll.) kanye neyunithi yetheminali, ayikuvumeli ukushintshwa kwedatha phakathi kwemishini yetheminali ehlukene. Iyunithi yetheminali ngayinye ngeke ibe nentambo yokuxhumana ngenkathi iqalisa, iphendula kuphela kusignali ye-rogatory ngokwayo.
Isikhathi sokuphendula sokusesha
Iyasesha
Ikhodi yokusebenza yolwazi lokusesha itshela iyunithi yesigqila ekhethiwe okufanele yenze ukuthi yiziphi izinhlobo zomsebenzi. Ingxenye yedatha ihlanganisa noma yiluphi ulwazi olungeziwe lapho iyunithi yesigqila izosebenzisa umsebenzi. Okwesiboneloample, ikhodi yokusebenza 03 edingekayo yokufunda gcina irejista evela kuyunithi yezinceku futhi ubuyisele okuqukethwe kwakho. Ingxenye yedatha kufanele iqukathe ulwazi oluzothunyelwa kuyunithi yezigqila: funda ukuthi irejista isuka kuyiphi kanye nenombolo yeRejista.Iphutha lokuthola indawo ihlinzeka ngeyunithi yesigqila ngendlela engaqinisekisa uma okuqukethwe kolwazi kulungile.
Ephendula
Uma iyunithi yesigqila iletha impendulo evamile,ikhodi yokusebenza yolwazi lwempendulo iyimpendulo yekhodi yokusebenza kulwazi lokuthungatha.Ingxenye yedatha ihlanganisa ukuqoqa idatha yeyunithi yesigqila: njengenani lerejista noma izwe. Uma kwenzeka iphutha, ikhodi yokusebenza izolungiswa ukuze kuboniswe ukuthi ulwazi lwempendulo alulungile, okwamanje, ingxenye yedatha iqukethe ikhodi echaza leli phutha. Iphutha ekutholeni indawo ivumela iyunithi enkulu ukuthi iqinisekise uma ulwazi lusetshenziswa.
Imodi yokudlulisa
- Imodi yokudlulisa iwuchungechunge lokucushwa kwedatha kumafreyimu wedatha kanye nomthetho we-finity osetshenziselwa ukudluliswa kwedatha.
- Imodi yokudlulisa ehambisana nemodi ye-MODBUS protocol-RTU ichazwa kanje.
Ibhithi ngayinye
- 1 isiqalo kancane
- 8 izingcezu zedatha, okuncane okusebenzayo okuletha kuqala
- Ayikho i-parity check bit
- 1 ima kancane
Iphutha ekuhloleni: I-CRC(isheke lokungaphelelwa umsebenzi wombuthano)
Iphrothokholi
Uma ifremu yedatha ifinyelela kuyunithi yetheminali, ingena ekhelini elicingayo lisuka “embobeni” elula .Iyunithi ikhipha “imvilophu” (ikhanda ledatha) bese ifunda idatha, bese yenza umgomo odingwa idatha uma lingekho iphutha.Ngemva kwalokho. , iyunithi yengeza idatha ekhiqiziwe ukuze "imboze" futhi ibuyisela uhlaka lwedatha kumthumeli. Idatha yezimpendulo ebuyisiwe ihlanganisa: Ikheli leyunithi yesigqila esibulalayo, Umsebenzi owenziwe, Idatha ekhiqiziwe kanye nesheke. Ayikho impendulo eyimpumelelo uma kwenzeka noma yiliphi iphutha, noma buyela ohlakeni olungamanga.
Ifomethi yohlaka lwedatha
| Ikheli | Umsebenzi | Idatha | Hlola |
| 8-bits | 8-bits | N x 8-amabhithi | 16-bits |
Isifunda sekheli
Isifunda sekheli esiyisiqalo sohlaka siqukethe ibhayithi( amabhithi angu-8 amakhodi kanambambili). I-decimalist ingu-0-255, futhi isistimu isebenzisa u-1-247. Amabhithi abonisa ikheli leyunithi yetheminali eqokwe abasebenzisi abathola idatha kukhompyutha yomsingathi exhunyiwe. Ikheli leyunithi yetheminali ngayinye kufanele likhetheke, futhi indawo eseshwayo izoletha ukusesha kwamakheli. Lapho itheminali ibuyisela impendulo, idatha yekheli lesigqila lempendulo itshela ikhompuyutha engusokhaya ukuthi iyiphi itheminali exhumana nayo.
Isifunda somsebenzi
Ikhodi yesifunda somsebenzi itshela itheminali eseshwayo ukuthi yimuphi umsebenzi okufanele wenziwe. Amakhodi okusebenza asetshenziswa kumitha ami kanje.
| Ikhodi | Incazelo | Isenzo |
| 03 noma 04 | Funda irejista yedatha | Thola inani kanambambili lamanje elilodwa noma ambalwa erejista |
| 16 | Setha ngaphambilini ukubhalisa okuningi | Setha inani kanambambili ochungechungeni lwe-multi-register |
Idethi yesifunda
- Isifunda sedatha sihlanganisa idatha ukuthi iyiphi itheminali edingekayo ukuze kwenziwe umsebenzi othile noma okungu-sampiholwa lapho izimpendulo zetheminali ziseshwa.
- Okuqukethwe kwedatha mhlawumbe inani lenombolo, ikheli lereferensi noma inani lokusetha. Okwesiboneloample: Umsebenzi
Iphutha ekuhloleni indawo
Isifunda sokuhlola sivumela iphutha phakathi kwekhompuyutha engusokhaya kanye nokudluliswa kwetheminali. Kwesinye isikhathi ngenxa yomsindo kagesi nokunye ukuphazamiseka, isethi yedatha ingashintsha ngenkathi idluliswa isuka kwenye iyunithi iye kwenye, ukuhlola iphutha kungaqinisekisa umsingathi noma itheminali ukuthi angayiphenduli idatha eshintshile.Kuthuthukisa ukuvikeleka nokusebenza kahle kwesistimu. Ukuhlola amaphutha kusebenzisa indlela ye-CRC16.
Iphrothokholi
Isifunda se-CRC sithatha amabhayithi angu-2, inani kanambambili amabhithi angu-16. Inani le-CRC libalwa ngeyunithi yokudlulisa, bese yengeza kuhlaka lwedatha. Iyunithi yomamukeli ibhala inani le-CRC futhi ngenkathi ithola idatha, bese iqhathaniswa nenani lesifunda se-CRC.Uma kokubili kungafani, kukhona iphutha.
Ngenkathi i-CRC isebenza，Setha kusengaphambili amabhithi angu-16 ubhalisa 1 kusengaphambili, bese usebenzisa amabhithi angu-8 ebhayithi ngayinye kufreyimu yedatha kanye nenani lamanje lerejista Ngokuqhubekayo.Amabhithi edatha angu-8 kuphela ebhayithi ngayinye abamba iqhaza ekwakheni i-CRC, engathonywa isiqalo kancane, yima. kancane kanye nokulinganisa kancane. Ngenkathi udala i-CRC. Amabhithi angu-8 ebhayithi ngayinye ngokukhethekile NOMA anokuqukethwe kurejista. Umphumela uhanjiswa kubhithi ephansi, "0" isetshenziswa kubhithi ephezulu. I-LSB iyaphuma futhi izotholwa, uma 1, irejista yenza umsebenzi okhethekile NOMA onenani elimisiwe elimisiwe(OA001H), uma ibhithi eliphansi kakhulu lingu-0, ungenzi lutho. Ukusebenza ngenhla kuqhubeka ngokuphindaphindiwe kuze kuqedwe ukunyakaza okungu-8 bit. Lapho ibhithi lokugcina lihamba, amabhithi angu-8 alandelayo enza umsebenzi okhethekile NOMA onenani lamanje lerejista. ngenkathi isebenza omunye wathi 8 bit ezihamba okukhethekile NOMA operation. Amabhayithi e-AII ayasebenza, inani le-CRC inani lokugcina.
Ukugeleza ukuze udale i-CRC:
- Setha kusengaphambili irejista yamabhithi ayi-16 OFFFFH kusengaphambili, ebizwa ngerejista ye-CRC.
- Amabhithi angu-8 ebhayithi yokuqala kuhlaka lwedatha enza umsebenzi okhethekile NOMA ngebhayithi ephansi kurejista ye-CRC futhi agcine umphumela kurejista ye-CRC.
- Hambisa irejista ye-CRC kancane uye kwesokudla, chaza u-0 ophezulu, khipha okuphansi kakhulu futhi ukuhlole.
- Uma ingxenye ephansi ingu-0, phinda isinyathelo sesi-3; uma kungu-1, irejista yenza umsebenzi okhethekile NOMA onenani elimisiwe elimisiwe (OA001H)
- Phinda isinyathelo sesi-3 nesesi-4 kuze kufike elesishiyagalombili. Amabhithi angu-8 wonke ashintshiwe.
- Phinda isinyathelo sesi-2 ukuya ku-5 ukuze ubhekane namabhithi angu-8 alandelayo kuze kube wonke amabhayithi enziwa.
- Inani le-CRC inani lokugcina lerejista ye-CRC.
Ngaphezu kwalokho, kunendlela yoku-akhawunti ye-CRC ngokumisa kuqala itafula kusengaphambili. Isici esiyinhloko ukushesha kwe-akhawunti, kodwa ithebula lidinga indawo yokugcina enkulu.
Incazelo yefomethi yokuxhumana
ExampLes kanjena isetshenziswa njengamathebula (hexadecimal).
| Addr | Okujabulisayo | Idatha iqala kabusha | Idatha iqala reg lo | Idatha #of reg sawubona | Idatha #of reg lo | CRC16 bheka | CRC16 sawubona |
| 01H | 03H | 00H | 00H | 00H | 03H | 05H | CBH |
Ukufunda( ikhodi yokusebenza 03 noma 04)
Isesha uhlaka lwedatha
Lo msebenzi uvumela umsebenzisi ukuthi athole ipharamitha yesistimu kanye nedatha ye-sampiholwa futhi irekhodwe yiyunithi. Ayikhawulelwe kunombolo yedatha edingwa ikhompuyutha engusokhaya kodwa ayikwazi ukweqa ububanzi bekheli obuchaziwe. I-ex elandelayoampngibonisa ukuthi kusukela ku-01 isigqila kukhompuyutha ukufunda ukufundwa kwedatha okuqoqiwe okubili, inani lokushisa elingu-CH1 kanye nenani lomswakama, ikheli lenani lokushisa ngu-0003H,ikheli lomswakama inani ngu-0004H, kokubili ubude buyi-2 byte.
| Addr | Okujabulisayo | Idatha iqala kabusha | Idatha iqala reg lo | Idatha #of reg sawubona | Idatha #of reg lo | CRC16 bheka | CRC16 sawubona |
| 01H | 03H | 00H | 01H | 00H | 02H | 95H | CBH |
Uhlaka lwedatha yempendulo
Impendulo ihlanganisa ikheli lekhompyutha yesigqila, ikhodi yokusebenza, ubude bebhayithi bedatha, idatha kanye nokuhlola amaphutha kwe-CRC. Ukulandela isibample yimpendulo yokufunda izinga lokushisa elingu-CH1, inani lomswakama.
| Addr | Okujabulisayo | Ukubala kwe-Byte | Idatha1 sawubona | Idatha ye-1 | Idatha 2 sawubona | Idatha ye-2 | CRC16 bheka | CRC16 sawubona |
| 01H | 03H | 04H | 01H | 20H | 02H | 5EH | 7AH | 9DH |
- izinga lokushisa= (0120H)/OAH = 288/10 = 28.8℃
- umswakama= (025EH)/OAH = 606/10 = 60.6%
Ithebula lekheli lemingcele yokufunda liboniswa kanje
| Addr | Okuqukethwe Kwedatha | Uhlobo lwedatha | Funda/Bhala | Izwi lomyalo | Qaphela |
|
0 |
Isimo sokusebenza:bit0～bit3 izindlela zokuqala Isimo sokusebenza:bit 4 ～ bit7 izindlela zesibili
Isimo sokusebenza:bit8～bit11 izindlela zesithathu Isimo se-Bit0 heater 0=ejwayelekile 1=iphutha Isimo senzwa ye-Bit1 0=evamile 1=iphutha Bit2 Isimo sokushisa 0=iyayeka 1=ukushisisa Isimo sokuqhuma kwe-Bit3 0=iyayeka 1=ukuqhuma |
Okungasayiniwe int |
R |
03 |
0; 4095 |
| 1 | Inani lezinga lokushisa likalwa esiteshini 1 | ungene ngemvume | R | 03 | |
| 2 | Inani lomswakamo likalwa esiteshini 1 | ungene ngemvume | R | 03 | |
| 3 | Inani lezinga lokushisa likalwa esiteshini 2 | ungene ngemvume | R | 03 | |
| 4 | Inani lomswakamo likalwa esiteshini 2 | ungene ngemvume | R | 03 | |
| 5 | Inani lezinga lokushisa likalwa esiteshini 3 | ungene ngemvume | R | 03 | |
| 6 | Inani lomswakamo likalwa esiteshini 3 | ungene ngemvume | R | 03 | |
|
7 |
Ikheli lokuxhumana lemitha |
Akusayiniwe
int |
R/W |
03, 04 / 16 |
1; 247 |
|
8 |
Imitha yokuxhumana kwe-baud rate |
Akusayiniwe
int |
R/W |
03, 04 / 16 |
0～4 bonisa 1200⽞19200
ngokulandelana |
|
9 |
Imvume ye-alamu kanye nemvume yesiteshi bit0～bit1 izindlela zokuqala
bit2 -bit3 izindlela zesibili I-bit4～bit5 iyindlela yesithathu ukutholwa kwephutha kwe-bit0 kwe-heater yokuqala: 0 imvume 1 vimbela I-Bit1 yisiteshi sokuqala esivuliwe: 0 vumela ukuvinjelwa okungu-1 |
Okungasayiniwe int |
R/W |
03, 04 / 16 |
0; 63 |
|
10 |
Imodi yokubonisa imitha |
Akusayiniwe
int |
R/W |
03, 04 / 16 |
Isikhathi sokuhamba ngebhayisikili(S),0FFH
khombisa okungewona amabhayisikili |
| 11 | Izinga lokushisa lihlelelwe ukuvuthela esiteshini 1 | ungene ngemvume | R/W | 03, 04 / 16 | 0; 1000 |
| 12 | Umswakamo usethelwe ukushisisa esiteshini 1 | ungene ngemvume | R/W | 03, 04 / 16 | 10; 999 |
| 13 | Izinga lokushisa lihlelelwe ukushisisa esiteshini 1 | ungene ngemvume | R/W | 03, 04 / 16 | - 400 - 1000 |
|
14 |
Inani le-hysteresis esiteshini 1 |
Akusayiniwe
int |
R/W |
03, 04 / 16 |
1～40(ibhayithi ephansi) |
| 15 | Izinga lokushisa lihlelelwe ukuvuthela esiteshini 2 | ungene ngemvume | R/W | 03, 04 / 16 | 0; 1000 |
| 16 | Umswakamo usethelwe ukushisisa esiteshini 2 | ungene ngemvume | R/W | 03, 04 / 16 | 10; 999 |
| 17 | Izinga lokushisa lihlelelwe ukushisisa esiteshini 2 | ungene ngemvume | R/W | 03, 04 / 16 | - 400 - 1000 |
|
18 |
Inani le-hysteresis esiteshini 2 |
Akusayiniwe
int |
R/W |
03, 04 / 16 |
1～40(ibhayithi ephansi) |
| 19 | Izinga lokushisa lihlelelwe ukuvuthela esiteshini 3 | ungene ngemvume | R/W | 03, 04 / 16 | 0; 1000 |
| 20 | Umswakamo usethelwe ukushisisa esiteshini 3 | ungene ngemvume | R/W | 03, 04 / 16 | 10; 999 |
| 21 | Izinga lokushisa lihlelelwe ukushisisa esiteshini 3 | ungene ngemvume | R/W | 03, 04 / 16 | - 400 - 1000 |
|
22 |
Inani le-hysteresis esiteshini 3 |
Akusayiniwe
int |
R/W |
03, 04 / 16 |
1～40(ibhayithi ephansi) |
|
23 |
I-Hysteresis yokushisisa nokupholisa esiteshini 1 |
Okungasayiniwe int |
R/W |
03 |
1 ～ 40(I-byte ephezulu iyafudumeza, i-byte ephansi iwukupholisa komoya
ukuqhuma) |
|
24 |
I-Hysteresis yokushisisa nokupholisa esiteshini 2 |
Okungasayiniwe int |
R/W |
03 |
1 ～ 40(I-byte ephezulu iyafudumeza, i-byte ephansi iwukupholisa komoya
ukuqhuma) |
|
25 |
I-Hysteresis yokushisisa nokupholisa esiteshini 3 |
Okungasayiniwe int |
R/W |
03 |
1 ～ 40(I-byte ephezulu iyafudumeza, i-byte ephansi iwukupholisa komoya
ukuqhuma) |
Hlela kusengaphambili ukubhalisa okuningi (Ikhodi yomsebenzi 16)
Isesha uhlaka lwedatha
Inani lokushisa elibekwe ukuqalisa i-heater ku-Channel 1 ngu-5℃, ikheli layo lokubhalisa ngu-0012H.
Ilethwa ikhompuyutha yokusingatha:
| Addr | Okujabulisayo | Idatha iqala kabusha | Idatha iqala reg lo | Idatha ye-reg Number Sawubona | Idatha ye-reg Number Lo | Idatha yinde | Idatha sawubona | Idatha ye | CRC16 bheka | CRC16 sawubona |
| 01H | 10H | 00H | 0DH | 00H | 01H | 02H | 00H | 32H | 26H | 98H |
Uhlaka lwedatha yempendulo
| Addr | Okujabulisayo | Idatha iqala kabusha | Idatha iqala reg lo | Idatha ye-reg Number Sawubona | Idatha ye-reg Number Lo | CRC16 bheka | CRC16 sawubona |
| 01H | 10H | 00H | 0DH | 00H | 01H | 90H | 0AH |
ISITHASISELO
Inzwa
Okujwayelekile
Inzwa ye-WHD Series Intelligent Temperature & Humidity Controller isebenzisa imodi yokuxhuma yangaphandle, kanye nezindlu ezikhethekile ezine-advantagumoya omuhle, ukubukeka kobuhle, ivikela ingxenye yangaphakathi ngempumelelo, ithuthukisa impilo yesevisi, ukukhweza kalula nokufaka izintambo.
Thayipha incazelo
I-WHD Series Inhloso ehlakaniphile lokushisa nenzwa yesilawuli somswakama:
| Uhlobo | Umsebenzi | Izintambo | Imodi yokukhweza | Usayizi we-Outline |
| WH-3 | Umswakama owodwa wezinga lokushisa | 
I-V+, V-, CLK, Idatha ixhunywe netheminali yezintambo efaniswayo yesilawuli ngokulandelanayo. |
Uhlobo lomhlahlandlela
Kulungisiwe |
|
Amadokhumenti / Izinsiza
 |
I-AcreL 259 WHD Temperature and Humidity Controller [pdf] Incwadi Yeziqondiso 259, WHD Temperature and Humidity Controller, Humidity Controller, Controller |
