UM1075
Imaniwali yosebenzisayo
ST-LINK/V2 in-circuit debugger/programmer
kwe-STM8 kanye ne-STM32
Isingeniso
I-ST-LINK/V2 iwuhlelo lokususa iphutha/uhlelo olungaphakathi kwesifunda lwe-STM8 kanye ne-STM32 microcontrollers. I-single wire interface module (SWIM) kanye ne-JTAG/i-serial wire debugging (SWD) interfaces isiza ukuxhumana nanoma iyiphi i-STM8 noma i-STM32 microcontroller esebenza ebhodini lohlelo.
Ngokungeziwe ekunikezeni ukusebenza okufanayo kwe-ST-LINK/V2, i-ST-LINK/V2-ISOL ifaka ukuhlukaniswa kwedijithali phakathi kwe-PC kanye nebhodi lesicelo eliqondiwe. Iphinde imelane ne-voltagkuze kufike ku-1000 V RMS.
I-interface ye-USB enesivinini esigcwele yenza ukuxhumana ne-PC kanye:
- Amadivayisi we-STM8 nge-ST Visual Develop (STVD) noma isofthiwe ye-ST Visual Program (STVP) (etholakala kwa-STMicroelectronics)
- Amadivayisi we-STM32 nge-IAR™, Keil ® , STM32CubeIDE, STM32CubeProgrammer, kanye ne-STM32CubeMonitor izindawo zokuthuthukisa ezididiyelwe.
Izici
- Amandla angu-5 V anikezwe isixhumi se-USB
- Isixhumi esibonakalayo esihambisana nesivinini esigcwele se-USB 2.0
- Intambo ye-USB ejwayelekile-A ukuya ku-Mini-B
- Izici eziqondene ne-SWIM
- 1.65 kuya ku-5.5 V isicelo voltagisekelwa kusixhumi esibonakalayo se-SWIM
- Izindlela ze-SWIM ezinejubane eliphansi nezinesivinini esikhulu ziyasekelwa
- Izinga lesivinini sohlelo lwe-SWIM: 9.7 kanye no-12.8 Kbytes/s, ngokulandelana, ngesivinini esiphansi nesiphezulu
- Ikhebula lokubhukuda lokuxhuma kuhlelo lokusebenza nge-ERNI ejwayelekile mpo (ref: 284697 noma 214017) noma isixhumi esivundlile (ref: 214012)
- Intambo yokubhukuda yokuxhuma kuhlelo lokusebenza ngesihloko sephini noma isixhumi se-pitch esingu-2.54 mm - JTAG/SWD (Serial Wire Debug) izici ezithile
- 1.65 kuya ku-3.6 V isicelo voltagesekelwe ku-JTAG/Isixhumi esibonakalayo se-SWD kanye nokokufaka kokubekezelela okungu-5 V (a)
– JTAG ikhebula lokuxhuma ku-J ejwayelekileTAG 20-pin pitch 2.54 mm isixhumi
- Usekela i-JTAG ukuxhumana, kufika ku-9 MHz (okuzenzakalelayo: 1.125 MHz)
- Isekela i-serial wire debug (SWD) kufika ku-4 MHz (okuzenzakalelayo: 1.8 MHz), kanye nentambo ye-serial viewer (SWV) ukuxhumana, kufika ku-2 MHz - Isici sokuvuselela i-firmware esiqondile siyasekelwa (i-DFU)
- Isimo se-LED, siyacwayiza ngesikhathi sokuxhumana ne-PC
- 1000 V RMS high isolation voltage (ST-LINK/V2-ISOL kuphela)
- Ukushisa okusebenzayo kusuka ku-0 kuye ku-50 degrees Celsius
Ulwazi loku-oda
Ukuze u-ode i-ST-LINK/V2, bheka kuThebula le-1.
Ithebula 1. Uhlu lwamakhodi e-oda
| Ikhodi ye-oda | Incazelo ye-ST-LINK |
| I-ST-LINK/V2 | I-debugger/umhleli wohlelo |
| ST-LINK/V2-ISOL | I-in-circuit debugger/umhleli onokuhlukaniswa kwedijithali |
a. I-ST-LINK/V2 ingaxhumana nezinto eziqondiwe ezisebenza ngaphansi kuka-3.3 V kodwa ikhiqize amasignali okukhiphayo kule voltage level. Okuhlosiwe kwe-STM32 kuyakubekezelela lokhu kuphuphumatage. Uma ezinye izingxenye zebhodi eliqondiwe zinengqondo, sebenzisa i-ST-LINK/V2-ISOL, STLINK-V3MINIE, noma i-STLINK-V3SET nge-adaptha ye-B-STLINK-VOLT ukuze ugweme umthelela wokugcwala ngokweqile.tage umjovo ebhodini.
Okuqukethwe komkhiqizo
Amakhebuli alethwe ngaphakathi komkhiqizo aboniswa kuMfanekiso 2 nakuMfanekiso 3. Ahlanganisa (kusuka kwesokunxele kuye kwesokudla):
- Intambo ye-USB ejwayelekile-A ukuya ku-Mini-B (A)
- ST-LINK/V2 ukulungisa iphutha nokuhlela (B)
- Isixhumi se-SWIM esibiza kancane (C)
- Iribhoni eliyisicaba le-SWIM elinesixhumi esijwayelekile se-ERNI ekugcineni kwesinye (D)
- JTAG noma iribhoni eliyisicaba le-SWD nele-SWV elinesixhumi samaphini angu-20 (E)
Ukucushwa kwezingxenyekazi zekhompuyutha
I-ST-LINK/V2 yakhelwe eduze kwedivayisi ye-STM32F103C8, ehlanganisa i-Arm esebenza kahle kakhulu ®(a) Cortex®
-M3 ingqikithi. Itholakala kuphakheji ye-TQFP48.
Njengoba kukhonjisiwe kuMfanekiso 4, i-ST-LINK/V2 inikeza izixhumi ezimbili:
- Isixhumi se-STM32 se-JTAG/ SWD kanye SWV interface
- Isixhumi se-STM8 sesixhumi esibonakalayo se-SWIM
I-ST-LINK/V2-ISOL inikeza isixhumi esisodwa se-STM8 SWIM, STM32 JTAG/SWD, kanye ne-SWV interface.
- A = STM32 JTAG kanye nesixhumi sethagethi ye-SWD
- B = STM8 SWIM target connector
- C = STM8 SWIM, STM32 JTAG, kanye nesixhumi sethagethi ye-SWD
- D = Umsebenzi wokuxhumana we-LED
4.1 Ukuxhumana ne-STM8
Ukuze kuthuthukiswe izinhlelo zokusebenza ezisuselwe kuzilawuli ezincane ze-STM8, i-ST-LINK/V2 ingaxhunywa ebhodini eliqondiwe ngamakhebuli amabili ahlukene, kuye ngesixhumi esitholakala ebhodini lohlelo lokusebenza.
Lawa makhebuli yilawa:
- Iribhoni eliyisicaba lokubhukuda elinesixhumi esijwayelekile se-ERNI ekugcineni
- Ikhebuli yoku-SWIM enamaphini angu-4 amabili, izixhumi ezingu-2.54 mm noma izintambo ezihlukene ze-SWIM
4.1.1 Ukuxhumana okujwayelekile kwe-ERNI neribhoni eliyisicaba le-SWIM
Umfanekiso 5 ubonisa indlela yokuxhuma i-ST-LINK/V2 uma isixhumi esijwayelekile se-ERNI 4-pin SWIM sikhona ebhodini lesicelo.
- A = Ibhodi lesicelo eliqondiwe elinesixhumi se-ERNI
- B = Intambo yocingo enesixhumi se-ERNI ekugcineni
- C = STM8 SWIM target connector
- Bheka Umfanekiso 11
Umfanekiso 6 ubonisa ukuthi iphinikhodi 16 ayikho kusixhumi esiqondiwe se-ST-LINK/V2-ISOL. Le phinikhodi engekho isetshenziswa njengokhiye wokuphepha kusixhumi sekhebula, ukuze kuqinisekiswe indawo efanele yekhebula le-SWIM kusixhumi esiqondiwe ngisho nezikhonkwane ezisetshenziselwa kokubili i-SWIM ne-J.TAG izintambo.
4.1.2 Uxhumano lwe-SWIM olubiza kancane
Umfanekiso 7 ubonisa indlela yokuxhuma i-ST-LINK/V2 uma i-4-pin, 2.54 mm, isixhumi se-SWIM esibiza kancane sikhona ebhodini lesicelo.
- A = Ibhodi lesicelo eliqondiwe elinamaphini angu-4, 2.54 mm, isixhumi esinezindleko eziphansi
- B = Ikhebula locingo elinesixhumi esinamaphini angu-4 noma intambo yocingo oluhlukene
- C = STM8 SWIM target connector
- Bheka Umfanekiso 12
4.1.3 Izimpawu zokubhukuda nokuxhumana
Ithebula le-2 lifingqa amagama esignali, imisebenzi, namasignali okuxhumana okuqondiwe lapho usebenzisa intambo yocingo ene-4-pin connector.
Ithebula 2. Ukuxhumana kweribhoni eyisicaba ye-SWIM ye-ST-LINK/V2
| Iphinikhodi | Igama | Umsebenzi | Uxhumano oluqondiwe |
| 1 | I-VDD | I-VCC eqondiwe(1) | I-MCU VCC |
| 2 | IDATHA | BHUNGA | Iphinikhodi ye-MCU SWIM |
| 3 | GND | UMHLABA | GND |
| 4 | SETHA KABUSHA | SETHA KABUSHA | Iphinikhodi ye-MCU RESET |
1. Ukunikezwa kwamandla okuvela ebhodini lesicelo kuxhunywe ku-ST-LINK/V2 yokulungisa iphutha kanye nebhodi lezinhlelo ukuze kuqinisekiswe ukuhambisana kwesignali phakathi kwawo womabili amabhodi.
Ithebula le-3 lifingqa amagama esignali, imisebenzi, namasignali okuxhumana okuqondiwe kusetshenziswa ikhebula yezintambo ezihlukene.
Njengoba intambo yocingo ehlukene ye-SWIM inezixhumi ezizimele zawo wonke amaphini ohlangothini olulodwa, kungenzeka ukuxhuma i-ST-LINK/V2-ISOL ebhodini lesicelo ngaphandle kwesixhumi esijwayelekile se-SWIM. Kule ribhoni eyisicaba, umbala othize kanye nelebula yokwenza lula ukuxhumeka kumareferensi okuqondiwe kuwo wonke amasignali.
Ithebula 3. SWIM ukuxhunywa kwekhebula elibiza kancane le-ST-LINK/V2-ISOL
| Umbala | Igama lephinikhodi yekhebula | Umsebenzi | Uxhumano oluqondiwe |
| Okubomvu | I-CCTV | I-VCC eqondiwe(1) | I-MCU VCC |
| Okuhlaza | UART-RX | Engasetshenzisiwe | Igodliwe (2) (ayixhunyiwe ebhodini eliqondiwe) |
| Okuluhlaza okwesibhakabhaka | UART-TX | ||
| Okuphuzi | I-BOOTO | ||
| iwolintshi | BHUNGA | BHUNGA | Iphinikhodi ye-MCU SWIM |
| Mnyama | GND | UMHLABA | GND |
| Emhlophe | SWIM-RST | SETHA KABUSHA | Iphinikhodi ye-MCU RESET |
1. Ukunikezwa kwamandla okuvela ebhodini lesicelo kuxhunywe ku-ST-LINK/V2 yokulungisa iphutha kanye nebhodi lezinhlelo ukuze kuqinisekiswe ukuhambisana kwesignali phakathi kwawo womabili amabhodi.
2. I-BOOT0, i-UART-TX, ne-UART-RX ibekelwe intuthuko yesikhathi esizayo.
I-TVCC, SWIM, GND, kanye ne-SWIM-RST ingaxhunywa kusixhumi se-pitch esibiza kancane esingu-2.54 mm noma ukuphina izihloko ezitholakala ebhodini eliqondiwe.
4.2 Ukuxhumana ne-STM32
Ngokuthuthukiswa kwezinhlelo zokusebenza ezisuselwe kuzilawuli ezincane ze-STM32, i-ST-LINK/V2 kufanele ixhunywe ohlelweni kusetshenziswa i-20-pin J ejwayelekile.TAG iribhoni flat enikeziwe.
Ithebula le-4 lifingqa amagama esignali, imisebenzi, namasignali okuhlosiwe okuhlosiwe we-standard 20-pin JTAG iribhoni eyisicaba ku-ST-LINK/V2.
Ithebula lesi-5 lifingqa amagama esignali, imisebenzi, namasignali okuxhumana okuqondiwe okujwayelekile okungu-20-pin JTAG iribhoni eyisicaba ku-ST-LINK/V2-ISOL.
Ithebula 4. JTAG/ukuxhumeka kwekhebula le-SWD ku-STLINK-V2
| Phina cha. | I-ST-LINK/V2 isixhumi (CN3) | I-ST-LINKN2 umsebenzi | Uxhumano oluqondiwe (JTAG) | Uxhumano oluqondiwe (SWD) |
| 1 | I-VAPP | I-VCC eqondiwe | I-MCU VDD(1) | I-MCU VDD(1) |
| 2 | ||||
| 3 | I-TRST | JTAG I-TRST | I-NJTRST | I-GND(2) |
| 4 | GND | GND | I-GNDK3) | I-GND(3) |
| 5 | TDI | JTAG I-TDO | I-JTDI | I-GND(2) |
| 6 | GND | GND | I-GND(3) | I-GND(3) |
| 7 | I-TMS SWDIO | JTAG TMS, SW 10 | I-JTMS | I-SWDIO |
| 8 | GND | GND | I-GND(3) | I-GND(3) |
| 9 | I-TCK SWCLK | JTAG TCK, SW CLK | I-JTCK | SWCLK |
| 10 | GND | GND | I-GND(3) | I-GND(3) |
| 11 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 12 | GND | GND | I-GND(3) | I-GND(3) |
| 13 | I-TDO SWO | JTAG TDI. SWO | I-JTDO | TRACESWOO) |
| 14 | GND | GND | I-GND(3) | I-GND(3) |
| 15 | I-NRST | I-NRST | I-NRST | I-NRST |
| 16 | GND | GND | I-GNDK3) | I-GND(3) |
| 17 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 18 | GND | GND | I-GND(3) | I-GND(3) |
| 19 | I-VDD | I-VDD (3.3 V) | Ayixhunyiwe | Ayixhunyiwe |
| 20 | GND | GND | I-GND(3) | I-GND(3) |
- Ukunikezwa kwamandla okuvela ebhodini lesicelo kuxhunywe ku-ST-LINK/V2 yokulungisa iphutha kanye nebhodi lezinhlelo ukuze kuqinisekiswe ukuhambisana kwesignali phakathi kwamabhodi.
- Xhuma ku-GND ukuze unciphise umsindo kuribhoni.
- Okungenani eyodwa yalezi phini kufanele ixhunywe phansi ukuze iziphathe kahle. Kunconywa ukuxhuma zonke.
- Ongakukhetha: Okwentambo yocingo Viewer (SWV) ukulandelela.
Ithebula 5. JTAG/ukuxhumeka kwekhebula le-SWD ku-STLINK-V2-ISOL
| Iphinikhodi | ST-LINK/V2 isixhumi (CN3) | Umsebenzi we-ST-LINKN2 | Ukuxhumana okuhlosiwe (JTAG) | Uxhumano oluqondiwe (SWD) |
| 1 | I-VAPP | I-VCC eqondiwe | I-MCU VDD(1) | I-MCU VDD(1) |
| 2 | ||||
| 3 | I-TRST | JTAG I-TRST | I-NJTRST | I-GND(2) |
| 4 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 5 | TDI | JTAG I-TDO | I-JTDI | I-GND(2) |
| 6 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 7 | I-TMS SWDIO | JTAG I-TMS. SW 10 | I-JTMS | I-SWDIO |
| 8 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 9 | I-TCK SWCLK | JTAG TCK, SW CLK | I-JTCK | SWCLK |
| 10 | Ayisetshenziswa(5) | Ayisetshenziswa(5) | Ayixhunyiwe(5) | Ayixhunyiwe(5) |
| 11 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 12 | GND | GND | I-GND(3) | I-GND(3) |
| 13 | I-TDO SWO | JTAG TDI, SWO | I-JTDO | I-TRACESW0(4) |
| 14 | Ayisetshenziswa(5) | Ayisetshenziswa(5) | Ayixhunyiwe(5) | Ayixhunyiwe(5) |
| 15 | I-NRST | I-NRST | I-NRST | I-NRST |
| 16 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 17 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 18 | GND | GND | I-GND(3) | I-GND(3) |
| 19 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 20 | GND | GND | I-GND(3) | I-GND(3) |
- Ukunikezwa kwamandla okuvela ebhodini lesicelo kuxhunywe ku-ST-LINK/V2 yokulungisa iphutha kanye nebhodi lezinhlelo ukuze kuqinisekiswe ukuhambisana kwesignali phakathi kwamabhodi.
- Xhuma ku-GND ukuze unciphise umsindo kuribhoni.
- Okungenani eyodwa yalezi phini kufanele ixhunywe phansi ukuze iziphathe kahle. Kunconywa ukuxhuma zonke.
- Ongakukhetha: Okwentambo yocingo Viewer (SWV) ukulandelela.
Ithebula 5. JTAG/ukuxhumeka kwekhebula le-SWD ku-STLINK-V2-ISOL
| Iphinikhodi | ST-LINK/V2 isixhumi (CN3) | Umsebenzi we-ST-LINKN2 | Ukuxhumana okuhlosiwe (JTAG) | Uxhumano oluqondiwe (SWD) |
| 1 | I-VAPP | I-VCC eqondiwe | I-MCU VDD(1) | I-MCU VDD(1) |
| 2 | ||||
| 3 | I-TRST | JTAG I-TRST | I-NJTRST | I-GND(2) |
| 4 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 5 | TDI | JTAG I-TDO | I-JTDI | I-GND(2) |
| 6 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 7 | I-TMS SWDIO | JTAG I-TMS. SW 10 | I-JTMS | I-SWDIO |
| 8 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 9 | I-TCK SWCLK | JTAG I-TCK. I-SW CLK | I-JTCK | SWCLK |
| 10 | Ayisetshenziswa(5) | Ayisetshenziswa(5) | Ayixhunyiwe(5) | Ayixhunyiwe(5) |
| 11 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 12 | GND | GND | I-GND(3) | I-GND(3) |
| 13 | I-TDO SWO | JTAG TDI. SWO | I-JTDO | I-TRACESW0(4) |
| 14 | Ayisetshenziswa(5) | Ayisetshenziswa(5) | Ayixhunyiwe(5) | Ayixhunyiwe(5) |
| 15 | I-NRST | I-NRST | I-NRST | I-NRST |
| 16 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 17 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 18 | GND | GND | I-GND(3) | I-GND(3) |
| 19 | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe | Ayixhunyiwe |
| 20 | GND | GND | I-GND(3) | I-GND(3) |
- Ukunikezwa kwamandla okuvela ebhodini lesicelo kuxhunywe ku-ST-LINK/V2 yokulungisa iphutha kanye nebhodi lezinhlelo ukuze kuqinisekiswe ukuhambisana kwesignali phakathi kwamabhodi.
- Xhuma ku-GND ukuze unciphise umsindo kuribhoni.
- Okungenani eyodwa yalezi phini kufanele ixhunywe phansi ukuze iziphathe kahle. Kunconywa ukuxhuma zonke.
- Ongakukhetha: Okwentambo yocingo Viewer (SWV) ukulandelela.
- Kusetshenziswa i-SWIM ku-ST-LINK/V2-ISOL (bona Ithebula 3).
Umfanekiso 9 ubonisa indlela yokuxhuma i-ST-LINK/V2 kokuthile kusetshenziswa i-JTAG ikhebula.
- A = Ibhodi lesicelo eliqondiwe no-JTAG isixhumi
- B = JTAG/SWD 20-wire flat cable
- C = STM32 JTAG kanye nesixhumi sethagethi ye-SWD
Ireferensi yesixhumi esidingekayo ebhodini lesicelo eliqondiwe yileli: 2x10C unhlokweni ogoqa 2x40C H3/9.5 (pitch 2.54) - HED20 SCOTT Idatha ye-PHSD80.
Qaphela: Kuzinhlelo zokusebenza ezishibhile, noma uma isixhumi esijwayelekile esingu-20-pin 2.54 mm-pitch sisikhulu kakhulu, kungenzeka ukusebenzisa TAG- Xhuma isixazululo. I TAG-I-adaptha yokuxhuma nekhebula inikeza izindlela ezilula nezithembekile zokuxhuma i-ST-LINK/V2 noma i-ST-LINK/V2ISOL ku-PCB ngaphandle kokudinga ingxenye yokukhwelana ku-PCB yohlelo lokusebenza.
Ukuze uthole imininingwane eyengeziwe ngalesi sixazululo kanye nolwazi lwe-PCB-footprint, vakashela www.tag-xhuma.com.
Izinkomba zezingxenye ezihambisana ne-JTAG kanye ne-SWD interface yilezi:
a) I-adaptha ye-TC2050-ARM2010 (ibhodi yokuhlanganisa-amaphini angu-20 ukuya kwangu-10)
b) I-TC2050-IDC noma i-TC2050-IDC-NL (Ayikho imilenze) (ikhebula lamaphini angu-10)
c) I-TC2050-CLIP egcina isiqeshana esizosetshenziswa ne-TC2050-IDC-NL (uma uthanda)
4.3 ST-LINK/V2 isimo se-LED
I-LED enelebuli engu-COM phezu kwe-ST-LINK/V2 ibonisa isimo se-ST-LINK/V2 (noma yiluphi uhlobo lokuxhumeka). Imininingwane:
- I-LED icwayiza ngokubomvu: ukubala kokuqala kwe-USB nge-PC kuyenzeka
- I-LED ibomvu: ukuxhumana phakathi kwe-PC ne-ST-LINK/V2 kuyasungulwa (ukuphela kokubala)
- I-LED icwayiza ngokuluhlaza/bomvu: Idatha ishintshaniswa phakathi kwethagethi ne-PC
- I-LED iluhlaza: ukuxhumana kokugcina kube yimpumelelo
- I-LED inombala osawolintshi: Ukuxhumana kwe-ST-LINK/V2 nethagethi kuhlulekile.
Ukumiswa kwesoftware
5.1 ST-LINK/V2 ukuthuthukiswa kwe-firmware
I-ST-LINK/V2 ishumeka indlela yokuthuthukisa i-firmware yokuthuthukiswa kwasendaweni ngembobo ye-USB. Njengoba i-firmware ingashintsha phakathi nokuphila komkhiqizo we-ST-LINK/V2 (ukusebenza okusha, ukulungiswa kweziphazamisi, ukusekelwa kwemindeni emisha ye-microcontroller), kunconywa ukuthi ngezikhathi ezithile uvakashele amakhasi azinikele www.st.com ukuze uhlale unolwazi lwakamuva ngenguqulo yakamuva.
5.2 Ukuthuthukiswa kwesicelo se-STM8
Bheka ku-ST toolset Pack24 enepheshi 1 noma yakamuva kakhulu, ehlanganisa i-ST Visual Develop (STVD) kanye ne-ST Visual Programmer (STVP).
5.3 Ukuthuthukiswa kwesicelo se-STM32 kanye nokuhlelwa kwe-flash
Izintambo zamathuluzi ezinkampani zangaphandle (IAR ™ EWARM, Keil ® MDK-ARM ™ ) zisekela i-ST-LINK/V2 ngokuvumelana nezinguqulo ezinikezwe kuThebula 6 noma inguqulo yakamuva etholakalayo.
Ithebula 6. Indlela amaketanga ezinkampani zangaphandle ayisekela ngayo i-ST-LINK/V2
| Ilungu langaphandle | I-Toolchain | Inguqulo |
| I-IAR™ | I-EWARM | 6.2 |
| I-Keil® | I-MDK-ARM™ | 4.2 |
I-ST-LINK/V2 idinga umshayeli we-USB ozinikele. Uma ukusethwa kwesethi yamathuluzi kungayifaki ngokuzenzakalelayo, umshayeli angatholakala evuliwe www.st.com ngaphansi kwegama elithi STSW-LINK009.
Ukuze uthole ulwazi olwengeziwe ngamathuluzi ezinkampani zangaphandle, vakashela okulandelayo webamasayithi:
Ama-Schematics
Ilejendi yezincazelo zephinikhodi:
I-VDD = I-Target voltage umqondo
IDATHA = SWIM DATA umugqa phakathi kwethagethi nethuluzi lokususa iphutha
GND = Ivolumu yomhlabathitage
SETHA KABUSHA = Ukusetha kabusha isistimu eqondiwe
Ilejendi yezincazelo zephinikhodi:
I-VDD = I-Target voltage umqondo
IDATHA = SWIM DATA umugqa phakathi kwethagethi nethuluzi lokususa iphutha
GND = Ivolumu yomhlabathitage
SETHA KABUSHA = Ukusetha kabusha isistimu eqondiwe
Umlando wokubuyekeza
Ithebula 7. Umlando wokubuyekeza idokhumenti
| Usuku | Buyekeza | Izinguquko |
| 22-Ephreli-11 | 1 | Ukukhishwa kokuqala. |
| 3-Juni-11 | 2 | Ithebula 2: Izixhumanisi zeribhoni le-SWIM eliyisicaba le-ST-LINK/V2: wengeze umbhalo waphansi 1 kumsebenzi othi “I-VCC eqondisiwe”. Ithebula 4: JTAG/ Ukuxhumeka kwekhebula le-SWD: wengeze umbhalo waphansi kumsebenzi othi "Target VCC". Ithebula 5: Indlela amaketanga amathuluzi enkampani yangaphandle ayisekela ngayo i-ST-LINK/V2: ibuyekeze “Izinguqulo” ze-IAR ne-Keil. |
| 19-Aug-11 | 3 | Kwengezwe imininingwane yomshayeli we-USB eSigabeni 5.3. |
| 11-May-12 | 4 | Kwengezwe i-SWD ne-SWV ku-JTAG izici zokuxhumana. Ithebula 4 Eliguquliwe: JTAG/ukuxhumana kwekhebula le-SWD. |
| 13-Sep-12 | 5 | Kwengezwe ikhodi ye-oda ye-ST-LINKN2-ISOL. Kubuyekeziwe Isigaba 4.1: Ukuthuthukiswa kwesicelo se-STM8 ekhasini 15. Kwengezwe Inothi 6 kuThebula 4. Kungezwe Inothi “Okwezinhlelo zokusebenza ezishibhile…” ngaphambi kweSigaba 3.3: STLINK/V2 isimo sama-LED ekhasini 14. |
| 18-Oct-12 | 6 | Kwengezwe Isigaba 5.1: Ukuthuthukiswa kwe-firmware ye-ST-LINK/V2 ekhasini 15. |
| 25-Mar-16 | 7 | Kubuyekezwe inani le-VRMS Kusethulo nezici. |
| 18-Oct-18 | 8 | Kubuyekeziwe Ithebula 4: JTAG/ukuxhumeka kwekhebula le-SWD kanye nemibhalo yayo yaphansi. Ukuhlelwa kombhalo omncane kuyo yonke idokhumenti. |
| 9-Jan-23 | 9 | Isingeniso Esibuyekeziwe, Izici, kanye neSigaba 5.3: Ukuthuthukiswa kohlelo lokusebenza lwe-STM32 nokuhlelwa kwe-flash. Ithebula 5 elibuyekeziwe: Indlela amaketanga amathuluzi enkampani yangaphandle ayisekela ngayo i-ST-LINK/V2. Ukuhlelwa kombhalo omncane kuyo yonke idokhumenti. |
| 3-Ephreli-24 | 10 | Ithebula 4 JTAG/Izixhumanisi zekhebula le-SWD zihlukaniswe kuThebula 4: JTAG/ukuxhumeka kwekhebula le-SWD ku-STLINK-V2 nakuThebula 5: JTAG/ukuxhumeka kwekhebula le-SWD ku-STLINK-V2-ISOL. |
ISAZISO ESIBALULEKILE – FUNDA NGOKUQAPHELA
I-STMicroelectronics NV nezinkampani ezingaphansi kwayo (“ST”) igodla ilungelo lokwenza izinguquko, ukulungisa, izithuthukisi, ukuguqulwa, nokuthuthukiswa kwemikhiqizo ye-ST kanye/noma kulo mbhalo nganoma yisiphi isikhathi ngaphandle kwesaziso. Abathengi kufanele bathole ulwazi lwakamuva olufanele ngemikhiqizo ye-ST ngaphambi kokufaka ama-oda. Imikhiqizo ye-ST ithengiswa ngokulandela imigomo nemibandela ye-ST yokuthengisa ekhona ngesikhathi sokuvunywa kwe-oda. Abathengi banomthwalo wemfanelo kuphela ekukhetheni, ekukhethweni, nasekusetshenzisweni kwemikhiqizo ye-ST futhi i-ST ayithathi sikweletu sosizo lwesicelo noma idizayini yemikhiqizo yabathengi.
Ayikho ilayisensi, eshiwo noma eshiwoyo, kunoma yiliphi ilungelo lempahla yengqondo elinikezwa i-ST lapha.
Ukudayiswa kabusha kwemikhiqizo ye-ST nezinhlinzeko ezihlukile kulwazi olubekwe lapha kuzovala noma yisiphi isiqinisekiso esinikezwe i-ST salowo mkhiqizo.
Ilogo ye-ST kanye ne-ST yizimpawu zokuthengisa ze-ST. Ukuze uthole ulwazi olwengeziwe mayelana nezimpawu zokuthengisa ze-ST, bheka ku www.st.com/trademarks. Wonke amanye amagama omkhiqizo noma wesevisi ayimpahla yabanikazi abafanele.
Ulwazi olukule dokhumenti luthatha indawo futhi luthatha indawo yolwazi olwalunikezwe ngaphambilini kunoma yiziphi izinguqulo zangaphambili zalo mbhalo.
© 2024 STMicroelectronics – Wonke amalungelo agodliwe
Amadokhumenti / Izinsiza
 |
I-ST-LINK-V2 Ku-Circuit Debugger Programmer [pdf] Imaniwali yosebenzisayo ST-LINK-V2, ST-LINK-V2-ISOL, ST-LINK-V2 Ku-Circuit Debugger Programmer, ST-LINK-V2, In Circuit Debugger Programmer, Circuit Debugger Programmer, Debugger Programmer |