I-Surenoo SLC2004B Series Display Character LCD Display
Sicela uchofoze isithombe esilandelayo ukuze uthenge ama-sample
I-Reference Controller Datasheet
Umhlahlandlela Wokukhetha I-LCD yezinhlamvu
UKU-ODA ULWAZI
Ithebula le-SLC2004B Series
SLC2004B Series Im age
*Inombolo yesithombe sochungechunge ihambisana nenombolo yethebula lochungechunge olungenhla 1.1.
INKCAZO
Ukucaciswa kwesibonisi
| Into | Inani Elijwayelekile | Iyunithi |
| Ifomethi yokubonisa | 20 Izinhlamvu x 4 Imigqa | - |
| Bonisa Isixhumi | Phina Unhlokweni, 16/18 pin | - |
| Isixhumi se-FPC | N/A | - |
| Izinga Lokushisa Lokusebenza | -20 ~ +70 | ℃ |
| Izinga Lokushisa Lesitoreji | -30 ~ +80 | ℃ |
| Iphaneli Yokuthinta Uyazikhethela | Cha | - |
| Ukukhanya kwelanga kuyafundeka | - |
Ukucaciswa Kwemishini
| Into | Inani Elijwayelekile | Iyunithi |
| I-Outline Dimension | 146.0(W) x 62.5(H)x13.0(T) | mm |
| Indawo Ebonwayo | 123.5(W) x 43.0(H) | mm |
| Indawo Esebenzayo | 118.84(W) x 38.47(H) | mm |
| Usayizi Wechashaza | 0.92×1.10 | mm |
| I-Dot Pitch | 0.98×1.16 | mm |
Ukucaciswa kukagesi
| Into | Inani Elijwayelekile | Iyunithi |
| Iphakheji ye-IC | I-COB | - |
| Isilawuli | I-AIP31066 noma i-Equivalent KS0066 noma i-SPLC780 | - |
| Isixhumi esibonakalayo | 6800 8-bit Parallel, 6800 4-bit Parallel | - |
Ukucaciswa kwe-Optical
| Into | Inani Elijwayelekile | Iyunithi |
| Uhlobo LCD | Bheka Ithebula le-1.1 SLC2004B Series | - |
| Viewnge-Angle Range | 6:00 | - |
| Umbala Wokukhanya Kwasemuva | Bheka Ithebula le-1.1 SLC2004B Series | - |
| Umsebenzi we-LCD | 1/16 | - |
| Ukuchema kwe-LCD | 1/5 | - |
UMDWEBO OMHLE
Ukucushwa kwePin
| Iphinikhodi No | Phina Igama | Izincazelo |
| 1 | I-VSS | Indawo, 0V |
| 2 | I-VDD | I-Logic Power Supply |
| 3 | V0 | I-vol esebenzayotage ye-LCD |
| 4 | RS | Khetha Irejista Yedatha / Yeziqondiso (H: Isignali Yedatha, L: Isignali Yemiyalo) |
| 5 | R/W | Funda / Bhala (H: Imodi yokufunda, L: Imodi yokubhala) |
| 6 | E | Nika amandla Isiginali |
| 7 | DB0 | I-Data Bit 0 |
| 8 | DB1 | I-Data Bit 1 |
| 9 | DB2 | I-Data Bit 2 |
| 10 | DB3 | I-Data Bit 3 |
| 11 | DB4 | I-Data Bit 4 |
| 12 | DB5 | I-Data Bit 5 |
| 13 | DB6 | I-Data Bit 6 |
| 14 | DB7 | I-Data Bit 7 |
| 15 | I-LED_A | I-Backlight Anode |
| 16 phezulu | I-LED_K | I-Backlight Cathode |
| 17 | NC | |
| 18 phezulu | NC |
VDD-V0=Ivolumu yokusebenzatage ye-LCD
Izilinganiso Eziphelele Eziphelele
Izici zikagesi
INDLELA YOKUHLOLA
Ileveli Yekhwalithi Eyamukelekayo
28B285B282BEach lot kufanele anelise izinga lekhwalithi elichazwe ngale ndlela elandelayo
| I-PARTITION | I-AQL | INCAZELO |
| A. Omkhulu | 0.4% | Ukungasebenzi kahle njengomkhiqizo |
| B. Mncane | 1.50/0 | Ukwanelisa yonke imisebenzi njengomkhiqizo kodwa unganeliseki ngezinga lezimonyo |
Incazelo yegama elithi Loti
Ingxenye eyodwa isho inani lokulethwa kukhasimende ngesikhathi esisodwa.
Umbandela Wokuhlolwa Kwezimonyo
- UKUHLOLA NOKUHLOLA
- ISIVIVINYO SOMSEBENZI
- UKUHLOLA UKUBUKEKA
- INGCACISO YOKUPAKA
- ISIMO SOKUHLOLA
- Beka ngaphansi kwe-lamp (20WiÅ2) ebangeni elingu-100mm ukusuka
- Tshekisa uqonde 45 degree ngaphambili (emuva) ukuze uhlole ukubukeka kwe-LCD.
IZINGA LOKUHLOLA I-AQL
- SAMPINDLELA YOKULINGWA: MIL-STD-105D
- SAMPUHLELO LOKUPHAKATHI: SINGLE
- IPHUMA ELIKHULU: 0.4% (OKUKHULU)
- UKUPHUMA OKUNCANE: 1.5% (OKUNCANE)
- IZINGA JIKELELE: II/EJWAYELEKILE
I-Module Cosmetic Criteria
| CHA. | Into | Umbandela Wokwahlulela | Ukwahlukanisa | |||
| 1 | Umehluko ku-Spec. | Akukho okuvunyelwe | Okukhulu | |||
| 2 | Ukucwecwa Kwephethini | Ayikho iphethini ye-substrate exebukayo futhi entantayo | Okukhulu | |||
| 3 | Amaphutha e-Soldering | Akukho ukusoda okungekho | Okukhulu | |||
| Alikho ibhuloho elihlanganisiwe | Okukhulu | |||||
| Akukho ukusoda okubandayo | Okuncane | |||||
| 4 | Melana nokushiyeka ku-substrate | I-foil yethusi engabonakali(￠0.5mm noma ngaphezulu) kuphethini ye-substrate | Okuncane | |||
| 5 | Ukwanda kwe-metallicForeign matter | Alukho uthuli lwe-soldering | Okuncane | |||
| Akukho ukukhuphuka kwezindaba ze-metallic zangaphandle (Akungeqi￠0.2mm) | ||||||
| 6 | Ibala | Ayikho ibala ezonakalisa izimonyo kabi | Okuncane | |||
| 7 | Ipuleti elishintsha umbala | Alikho ipuleti elifiphalayo, eligqwalile futhi liyashintsha umbala | Okuncane | |||
| 8 | Inani le-solder 1.Izingxenye zokuhola | Uhlangothi lwe-soldering lwe-PCB I-Solder ukwenza i-a'Filet' nxazonke umthofu.I-Solder akufanele ifihle ifomu lokuhola kahle.(kakhulu)Uhlangothi lwezingxenye(Uma kwenzeka 'Nge-Hole PCB') I-Solder ukuze ifinyelele ohlangothini lwe-Components ye-PCB |
Okuncane | |||
| 2.Amaphakheji ayisicaba | Kuphakathi kokuthi 'uzwane' (A) noma 'ukuphulukisa' (B) kokuhola okuzohlanganiswa 'Filet Ifomu lokuhola lizothathwa phezu kwe-Solder. |
A | B | Okuncane | ||
| 3.Ama-chips | (3/2) H≧h≧(1/2)H |
h | H | Okuncane | ||
| 9 | Ukulimala kwe-Backlight |
|
Bona uhlu← |
| 10 | Izinkinga ze-PCB |
|
Bona uhlu← |
| 11 | Amaphutha e-Soldering |
|
Okuncane |
Umbandela Wezimonyo Zesikrini (Asisebenzi)
| Cha. | Isici | Ukwahlulela Umbandela | Ukwahlukanisa | |
| 1 | Amabala | Ngokuhambisana ne-Screen Cosmetic Criteria (Operating) No.1. | Okuncane | |
| 2 | Imigqa | Ngokuvumelana ne-Screen Cosmetic Criteria (Ukusebenza) No.2. | Okuncane | |
| 3 | Amabhamuza ku-Polarizer | Okuncane | ||
| Usayizi: d mm | I-Qty eyamukelekile endaweni esebenzayo | |||
| d≦0.3 0.3 | Ukunganaki 310 | |||
| 4 | Klwelwa | Ngokuvumelana namabala nemigqa yokusebenza kwemibandela yezimonyo, Lapho ukukhanya kubonakalisa endaweni yephaneli, imihuzuko akufanele iphawuleke. | Okuncane | |
| 5 | Ukuminyana okuvumelekile | Iziphambeko ezingenhla kufanele zihlukaniswe ngaphezu kuka-30mm komunye nomunye. | Okuncane | |
| 6 | Umbala | Akumele kubonakale umbala ku- viewIndawo yamaphaneli e-LCD. Uhlobo olukhanyiswe ngemuva kufanele lwahlulelwe ngokukhanyiswa okungemuva esimeni kuphela. | Okuncane | |
| 7 | Ukungcola | Akumele kubonakale. | Okuncane | |
Umbandela Wezimonyo Zesikrini (Ukusebenza)
| Cha. | Isici | Ukwahlulela Umbandela | Ukwahlukanisa | |
| 1 | Amabala | A) Kucacile | Okuncane | |
| Usayizi:d mm | I-Qty eyamukelekile endaweni esebenzayo | |||
| d≦0.1 0.1 | Ukunganaki 620 | |||
| Qaphela: Kuhlanganisa nezimbobo zokukhonkwane namachashazi angalungile okufanele abe phakathi kosayizi wephikseli eyodwa.B) Akucacile | ||||
| Usayizi:d mm | I-Qty eyamukelekile endaweni esebenzayo | |||
| d≦0.2 0.2 | Ukunganaki 620 | |||
| 2 | Imigqa | Kucace Qaphela: () – Ubuningi Obumukelekayo endaweni esebenzayo L – Ubude (mm)W -Ububanzi(mm)∞-DisregardB) Akucacile |
Okuncane | |
'Sula' = Umthunzi nosayizi akushintshwa yi-Vo.
'Akucacile' = Umthunzi nosayizi kushintshwa nguVo.
| Cha. | Isici | Ukwahlulela Umbandela | Ukwahlukanisa |
| 3 | Umugqa wokuhlikihla | Akumele kubonakale. | |
| 4 | Ukuminyana okuvumelekile | Iziphambeko ezingenhla kufanele zihlukaniswe ngaphezu kuka-10mm komunye nomunye. | Okuncane |
| 5 | Uthingo | Akumele kubonakale. | Okuncane |
| 6 | Usayizi wamachashazi | Ukuze ube ngu-95%~105%kasayizi wamachashazi (Uhlobo.) emdwebeni. | Okuncane |
| Ukushiyeka okuncane kwechashazi ngalinye (ex.pin-hole) kufanele kuthathwe njenge-spot'. (bona Inqubo Yezimonyo Zesikrini (Esebenzayo) No.1) | |||
| 7 | Ukukhanya (kuphela Imojula yokukhanyisa emuva) | Ukukhanya Okufanayo kumelwe kube BMAX/BMIN≦2- BMAX :Ubukhulu.inani ngesilinganiso ngamaphoyinti angu-5- BMIN : Inani elincane ngesilinganiso ngamaphoyinti angu-5Hlukanisa indawo esebenzayo ibe ngu-4 ngokuqondile nangokuvundlile. Kala amaphuzu angu-5 aboniswe emfanekisweni olandelayo. |
Okuncane |
| 8 | Qhathanisa Ukufana | Ukungafani Okungafani kufanele kube BmAX/BMIN≦2 Kala amaphoyinti angu-5 aboniswe emfanekisweni olandelayo.Imigqa edayishiwe ihlukanisa indawo esebenzayo ibe ngu-4 ngokuqondile nangokuvundlile. Amaphuzu okulinganisa atholakala phakathi kwezigaba zomugqa onedeshi.  Qaphela: BMAX – Max.value ngesilinganiso ngamaphoyinti angu-5. BMIN – Min.value ngesilinganiso ngamaphoyinti angu-5. O – Amaphuzu okulinganisa ngo-￠10mm. |
Okuncane |
Qaphela:
|
|||
IZIQINISEKISO ZOKUSEBENZISA
- Ukuphatha Izinyathelo Zokuqapha
- Le divayisi isengozini yokulimala kwe-Electro-Static Discharge (ESD). Qaphela izinyathelo zokuphepha ze-Anti-Static.
- Iphaneli yokubonisa ye-SUR yenziwe ngengilazi. Ungayifaki ekushayweni kwemishini ngokuyiwisa noma ngokuyithinta.
- Uma iphaneli yokubonisa ye-SUR yonakalisiwe futhi i-liquid crystal substance iphuma, qiniseka ukuthi awutholi lutho emlonyeni wakho. Uma into ithinta isikhumba noma izingubo zakho, zigeze usebenzisa insipho namanzi.
- Ungasebenzisi amandla eqile endaweni yesibonisi ye-SUR noma ezindaweni ezixhumene njengoba lokhu kungase kubangele ithoni yombala ihluke.
- I-polarizer emboze indawo yokubonisa ye-SUR yemojuli ye-LCD ithambile futhi iklwejwa kalula. Phatha le polarizer ngokucophelela.
- Uma indawo yokubonisa ye-SUR ingcoliswa, phefumulela phezulu bese uyisula kahle ngendwangu ethambile eyomile. Uma ingcoliswe kakhulu, manzisa indwangu ngenye yalezi ezilandelayo Isopropyl noma utshwala.
- Izincibilikisi ngaphandle kwalezo ezibalwe ngenhla zingalimaza i-polarizer. Ikakhulukazi, ungasebenzisi Amanzi.
- Zivocavoce ukuze unciphise ukugqwala kwe-electrode. Ukugqwala kwama-electrode kusheshiswa ngamaconsi amanzi, ukufiphala komswakama noma ukugeleza kwamanje endaweni enomswakama ophezulu.
- Faka i-SUR LCD Module ngokusebenzisa izimbobo ezifakwayo. Uma ukhweza imojula ye-LCD qiniseka ukuthi ayisonti, ihlanekezelwe futhi ihlanekezelwe. Ikakhulukazi, ungadonsi ngenkani noma ugobise ikhebula noma ikhebula le-backlight.
- Ungazami ukuqaqa noma ukucubungula imojuli ye-SUR LCD.
- Itheminali ye-NC kufanele ivuleke. Ungaxhumi lutho.
- Uma amandla esekethe enengqondo evaliwe, ungawasebenzisi amasignali okokufaka.
- Ukuze uvimbele ukucekelwa phansi kwezakhi ngogesi omile, qaphela ukugcina indawo yokusebenza efanele.
- Qiniseka ukuthi ugxilisa umzimba lapho uphatha amamojula e-SUR LCD.
- Amathuluzi adingekayo ukuze kuhlanganiswe, njengama-ayina ahlanganisiwe, kufanele asekelwe kahle.
- Ukuze unciphise inani likagesi omile okhiqizwayo, ungaqhubi ukuhlanganisa neminye imisebenzi ngaphansi kwezimo ezomile.
- Imojula ye-LCD imbozwe ngefilimu ukuvikela indawo eboniswayo. Ziqeqeshe ngokucophelela lapho uxebula le filimu evikelayo njengoba kungase kukhiqizwe ugesi omile.
- Izinyathelo Zokuqaphela Ukunikezwa Amandla
- Khomba futhi, ngaso sonke isikhathi, ubheke izilinganiso eziphelele zazo zombili abashayeli be-logic kanye ne-LC. Qaphela ukuthi kukhona umehluko phakathi kwamamodeli.
- Vimbela ukusetshenziswa kokuhlehla kwe-polarity ku-VDD ne-VSS, kodwa kafushane.
- Sebenzisa umthombo wamandla ohlanzekile ongenazo izinto ezidlulayo. Izimo zokuqinisa amandla ngezikhathi ezithile ziyanyakaza futhi zingase zeqe umkhawulo wezilinganiso zamamojula we-SUR.
- Amandla e-VDD emojuli ye-SUR kufanele futhi anikeze amandla kuwo wonke amadivayisi angase afinyelele isibonisi. Ungavumeli ibhasi ledatha ukuthi lishayelwe lapho ukunikezwa okunengqondo kwemojuli kuvaliwe.
- Izinyathelo Zokusebenza
- UNGAYIxhume noma ukhiphe imojuli ye-SUR uma isistimu inikwe amandla.
- Nciphisa ubude bekhebula phakathi kwemojuli ye-SUR ne-MPU yosokhaya.
- Kumamodeli anamalambu angemuva, ungawacimi ukukhanya kwangemuva ngokuphazamisa ulayini we-HV. Ukukhipha ama-inverters akhiqiza i-voltagama-extras angangena ngaphakathi kwekhebuli noma esibukweni.
- Sebenzisa imojula ye-SUR ngaphakathi kwemikhawulo yokucaciswa kwezinga lokushisa kwamamojula.
- Izinyathelo Zokuqaphela Mechanical/Environmental
- I-solder engafanele iyimbangela enkulu yobunzima bemojula. Ukusetshenziswa kwe-flux cleaner akunconyiwe ngoba zingangena ngaphansi koxhumano lwe-electrometric futhi kubangele ukwehluleka kwesibonisi.
- Mount SUR module ukuze ikhululeke ku-torque kanye nengcindezi yemishini.
- Ubuso bephaneli ye-LCD akufanele ukuthintwa noma ukuklwejwa. Indawo engaphambili yesibonisi iyi-polarizer yepulasitiki eklwebheka kalula. Gwema ukuthintana futhi uhlanze kuphela uma kunesidingo ngokotini othambile, omuncayo dampifakwe nge-petroleum benzene.
- Hlala usebenzisa inqubo ye-anti-static ngenkathi uphethe imojuli ye-SUR.
- Vimbela ukunqwabelana komswakama phezu kwemojuli futhi ubheke izingqinamba zemvelo zokulondoloza izinga
- Ungagcini elangeni eliqondile
- Uma ukuvuza kwe-liquid crystal material kufanele kwenzeke, gwema ukuthintana nale nto, ikakhulukazi ukungeniswa. Uma umzimba noma izingubo zingcoliswa uketshezi oluyikristalu, geza kahle ngamanzi nensipho
- Izinyathelo Zokuqaphela Isitoreji
- Lapho ugcina amamojula e-LCD, gwema ukuchayeka elangeni eliqondile noma ekukhanyeni kwe-fluorescent l.amps. Gcina amamojula e-SUR ezikhwameni (gwema izinga lokushisa eliphezulu / umswakama ophezulu kanye namazinga okushisa aphansi ngaphansi kwe-OC Noma nini lapho kungenzeka, amamojula e-SUR LCD kufanele agcinwe ezimweni ezifanayo lapho athunyelwe khona ephuma enkampanini yethu.
- Abanye
Amakristalu oketshezi aqina ngaphansi kwezinga lokushisa eliphansi (ngaphansi kwebanga lokushisa lesitoreji) okuholela ekumukiseni okunesici noma ukukhiqizwa kwamabhamuza omoya (amnyama noma amhlophe). Amabhamuza omoya nawo angakhiqizwa uma imojuli ingaphansi kwezinga lokushisa eliphansi. Uma amamojula e-SUR LCD esebenza isikhathi eside ebonisa amaphethini wokubonisa afanayo, amaphethini wokubonisa angase asale esikrinini njengezithombe eziyisipoki futhi kungase kubonakale okungahambi kahle kokungafani okuncane. Isimo sokusebenza esijwayelekile singatholwa kabusha ngokumisa ukusetshenziswa isikhathi esithile. Kufanele kuqashelwe ukuthi lesi simo asithinti kabi ukuthembeka kokusebenza. Ukuze unciphise ukuwohloka kokusebenza kwamamojula e-LCD okubangelwa ukubhujiswa okubangelwa ugesi omile njll., sebenzisa ukunakekela ukuze ugweme ukubamba izigaba ezilandelayo lapho uphatha amamojula.- Indawo eveziwe yebhodi lesekethe ephrintiwe.
- Izingxenye ze-Terminal electrode.
UKUSEBENZISA AMAMODULE E-LCD
- I-Liquid Crystal Display Modules
- I-SUR LCD yenziwe ngengilazi kanye ne-polarizer. Naka izinto ezilandelayo lapho uphatha.
- Sicela ugcine izinga lokushisa ngaphakathi kwebanga elithile ukuze ulisebenzise futhi uligcine. Ukucekelwa phansi kwe-polarization, ukukhiqizwa kwamabhamuza noma ukuxetshulwa kwe-polarizer kungase kwenzeke ngokushisa okuphezulu kanye nomswakama ophezulu.
- Ungazithinti, uphushe noma uzihlikihle ama-polarizer aveziwe nganoma yini eqinile kunomsizi wepensela ye-HB (ingilazi, ama-tweezers, njll.).
- I-N-hexane ituswa ukuhlanza izinto ezinamathelayo ezisetshenziselwa ukunamathisela ama-polarizer angaphambili/angemuva kanye nezibonisi ezenziwe ngezinto eziphilayo ezizolinyazwa amakhemikhali afana ne-acetone, i-toluene, i-ethanol ne-isopropylalcohol.
- Uma indawo yokubonisa ye-SUR iba uthuli, sula kancane ukotini omuncayo noma okunye okuthambile okufana ne-chamois efakwe ku-benzin ye-petroleum. Ungakhuhli kanzima ukuze ugweme ukulimaza indawo eboniswayo.
- Sula amathe noma amaconsi amanzi ngokushesha, ukuthintana namanzi isikhathi eside kungabangela ukubola noma ukufiphala kombala.
- Gwema ukuthinta amafutha namafutha
- Ukuminyana endaweni kanye nokuthintana namatheminali ngenxa yamakhaza kuzolimaza, kungcolise ama-polarizer. Ngemuva kokuthi imikhiqizo ihlolwe ezingeni lokushisa eliphansi kufanele ifudunyezwe esitsheni ngaphambi kokuthi ifike lapho ithintana nomoya wegumbi lokushisa.
- Ungabeki noma unamathisele lutho endaweni yesibonisi ye-SUR ukuze ugweme ukushiya amamaki evuliwe.
- Ungathinti isibonisi ngezandla ezingenalutho. Lokhu kuzongcolisa indawo yesibonisi futhi kwehlise izinga lokushisa phakathi kwamatheminali (ezinye izimonyo zinqunywa kuma-polarizer).
- Njengoba ingilazi ithambile. Ivamise ukuba noma igwetshwe ngesikhathi sokuphatha ikakhulukazi emaphethelweni. Sicela ugweme ukuwisa noma ukuthuka.
- Ifaka amamojula e-LCD
- Vala ingaphezulu ngepuleti lokuvikela elikhanyayo ukuze uvikele i-polarizer neseli ye-LC.
- Lapho uhlanganisela i-LCM kwezinye izinto zokusebenza, i-spacer kuya kubhithi phakathi kwe-LCM kanye nepuleti elifakayo kufanele libe nobude obanele ukuze kugwenywe ukubangela ingcindezi endaweni yemojuli, ibhekisele ekucacisweni ngakunye kwezilinganiso. Ukubekezelela isilinganiso kufanele kube ngu-÷ 0.1mm.
- Isexwayiso Sokuphatha Amamojula e-LCD
Njengoba i-SUR LCM ihlangene futhi yalungiswa ngezinga eliphezulu lokunemba; gwema ukusebenzisa ukushaqeka ngokweqile kumojula noma ukwenza noma yiziphi izinguquko noma ukuguqulwa kuyo.- Ungashintshi, uguqule noma uguqule umumo wethebhu ohlakeni lwensimbi.
- Ungenzi izimbobo ezengeziwe ebhodini lesifunda eliphrintiwe, uguqule ukuma kwalo noma uguqule izikhundla zezingxenye okumele zinamathiselwe.
- Ungalimazi noma uguqule ukubhalwa kwe-patter ebhodini lesekethe eliphrintiwe
- Ungaluguquli ngokuphelele umucu werabha wedube (irabha eqhubayo) noma isixhumi sophawu lokushisa.
- Ngaphandle kokuhlanganisa i-interface, ungenzi noma yiziphi izinguquko noma ukuguqulwa nge-solder iron iron.
- Ungawisi, ungagobi noma usonte i-SUR LCM.
- I-Electro-Static Discharge Control
- Njengoba le mojula isebenzisa i-CMOS LSI, kufanele kuqashelwe okufanayo ekukhishweni kwe-electrostatic njenge-CMOS IC evamile.
- Qiniseka ukuthi uphansi lapho unikeza i-LCM.
- Ngaphambi kokukhipha i-LCM kukesi layo lokupakisha noma ukulihlanganisa nesethi, qiniseka ukuthi imojuli nomzimba wakho kunamandla afanayo kagesi.
- Lapho u-soldering itheminali ye-LCM, qiniseka ukuthi umthombo wamandla we-AC wensimbi e-solder awuvuzi.
- Uma usebenzisa isikrudrayiva sikagesi ukuze unamathisele i-LCM, isikrudrayiva kufanele sibe namandla aphansi ukuze sinciphise ngangokunokwenzeka noma yikuphi ukudluliswa kwamagagasi kagesi kukhiqize izinhlansi ezivela kumhambisi wenjini.
- Ngokusemandleni akho yenza amandla kagesi ezingubo zakho zokusebenza kanye nebhentshi lomsebenzi abe amandla aphansi.
- Ukunciphisa ukukhiqizwa kukagesi omile qaphela ukuthi umoya osemsebenzini ungomiswa kakhulu. Kunconywa umswakama ohlobene no-50% -60%.
- Isexwayiso Sokudayiswa ku-SUR LCM
- Qaphela okulandelayo lapho uhlanganisa intambo yomthofu, ikhebuli yesixhumi nokunye ku-LCM.
- I-soldering iron lokushisa : 280 °C10 ° C -Isikhathi sokudambisa: 3-4 sec.
- I-Solder: i-eutectic solder. Uma kusetshenziswa i-soldering flux, qiniseka ukuthi ususa noma iyiphi i-flux esele ngemuva kokuqeda ukusebenza kwe-soldering. (Lokhu akusebenzi esimweni sohlobo lwe-flux olungeyona i-halogen.) Kunconywa ukuthi uvikele indawo ye-LCD ngekhava ngesikhathi sokuhlanganisa ukuze uvimbele noma yimuphi umonakalo ngenxa ye-flux spatters.
- Lapho uhlanganisa iphaneli ye-electroluminescent kanye nebhodi le-PC, iphaneli nebhodi akufanele kukhishwe izikhathi ezingaphezu kwezintathu. Le nombolo ephezulu inqunywa izinga lokushisa kanye nezimo zesikhathi ezishiwo ngenhla, nakuba kungase kube nokuhluka okuthile kuye ngezinga lokushisa lensimbi ehlanganisiwe.
- Uma ukhipha iphaneli ye-electroluminescent ebhodini le-PC, qiniseka ukuthi i-solder incibilike ngokuphelele, iphedi elidayisiwe ebhodini le-PC lingonakala.
- Ukuqapha Kokusebenza
- Viewi-ing angle iyahlukahluka ngokushintsha kwe-liquid crystal driving voltage (VO). Lungisa i-VO ukuze ubonise ukugqama okuhle kakhulu.
- Ukushayela i-SUR LCD ku-voltage ngaphezu komkhawulo ifinyeza impilo yayo.
- Isikhathi sokuphendula sibambezeleka kakhulu ezingeni lokushisa elingaphansi kwebanga lokushisa lokusebenza. Nokho, lokhu akusho ukuthi i-LCD izobe ingekho ekuhlelweni. Izolulama uma ibuyela ebangeni lokushisa elishiwo.
- Uma indawo yokubonisa ye-SUR iphushwa kanzima phakathi nokusebenza, isibonisi sizoba esingajwayelekile. Nokho, izobuyela kokujwayelekile uma ivaliwe bese iphinde ivuleke.
- Ukufingqa kumatheminali kungabangela ukusabela kwe-electrochemical okuphazamisa isekethe yetheminali. Ngakho-ke, kufanele isetshenziswe ngaphansi kwesimo esihlobene esingu-40 ° C, 50% RH.
- Lapho ukhanyisa amandla, faka isignali ngayinye ngemva kwevolthi ephozithivu/negethivutage uzinzile.
- Iwaranti Enomkhawuko
- Ngaphandle uma kuvunyelwene phakathi kwe-SUR nekhasimende, i-SUR izoshintsha noma ilungise noma yimaphi amamojula ayo e-LCD atholakala engasebenzi kahle lapho ehlolwa ngokuhambisana nezindinganiso zokwamukela i-SUR LCD (amakhophi atholakala uma ecelwa) isikhathi esingangonyaka owodwa kusukela ngosuku lokuthunyelwa. Ukukhubazeka kwezimonyo/okubukwayo kufanele kubuyiselwe ku-SUR zingakapheli izinsuku ezingu-90 zokuthunyelwa. Ukuqinisekiswa kwalolo suku kuzosekelwe kumadokhumenti wempahla. Isibopho sezomthetho se-SUR sikhawulelwe ukulungisa kanye/noma ukushintshwa kwemigomo ebekwe ngenhla. I-SUR ngeke ibe nesibopho sanoma yimiphi imicimbi elandelayo noma elandelanayo.
- Inqubomgomo Yokubuyisela
Ayikho iwaranti enganikezwa uma izinyathelo ezishiwo ngenhla zinganakwa. I-ex ejwayelekileampukwephulwa kwemithetho yilezi:- Ingilazi ye-LCD ephukile. -Iso le-PCB lonakele noma lishintshiwe.
- Amakhondaktha e-PCB alimele.
- Umjikelezo ulungiswe nganoma iyiphi indlela, okuhlanganisa nokungezwa kwezingxenye.
- PCB tampihlanganiswe ngokugaya, ukuqopha noma ukudweba ukuvenisha.
- I-soldering noma ukuguqula i-bezel nganoma iyiphi indlela. Ukulungiswa kwemojuli kuzofakwa ku-invoyisi ekhasimendeni ngemva kwesivumelwano sobabili. Amamojula kufanele abuyiselwe anencazelo eyanele yokuhluleka noma amaphutha. Noma yiziphi izixhumi noma ikhebula elifakwe ikhasimende kufanele lisuswe ngokuphelele ngaphandle kokulimaza i-PCB eyelet, amakhondakta namatheminali.
Isiphetho semininingwane
I-Shenzhen Surenoo Technology Co., Ltd. www.surenoo.com
I-Skype: Surenoo365
imibuzo ejwayelekile ukubuzwa
Iliphi Izinga Lekhwalithi Elamukelekayo elishiwo esigabeni Semibandela Yokuhlola?
Izinga Lekhwalithi Elamukelekayo lichazwe eSigabeni 5.1 semanuwali yomsebenzisi futhi linikeza imihlahlandlela yokunquma amazinga ekhwalithi amukelekayo ngesikhathi sokuhlolwa.
Amadokhumenti / Izinsiza
 |
I-Surenoo SLC2004B Series Display Character LCD Display [pdf] Imaniwali yosebenzisayo I-SA3 LC2004B, SLC2004B Series Display Character LCD Display, SLC2004B Series, Display Character LCD Display, Character LCD Display, LCD Display, Display |