I-lcdwiki E32R40T LCD Isibonisi Sesikrini Sokuthinta
Imininingwane
- Product Name: LCDWIKI 4.0inch ESP32-32E E32R40T&E32N40T
- Bonisa Imojuli: 4.0inch ESP32-32E
- Inombolo Model: CR2025-MI3275
- Webindawo: www.lcdwiki.com
Amandla emkhiqizweni
Sebenzisa ikhebuli yohlobo C esebenza ngamandla kagesi kanye nomsebenzi wokudlulisa idatha ukuze uxhume ikhompuyutha emkhiqizweni futhi unike amandla umkhiqizo. Njengoba kukhonjisiwe esithombeni esingezansi:
Faka i-USB-to-serial port driver
- Locate the USB-SERIAL_CH340.zip package in the “7-工具软件_Tool_software” folder and decompress it.
- go to the folder after decompression, double-click “CH341SER.EXE” executable program, pop up the installation window, and then click “Install” button to continue the installation, as shown in the following picture:
After the installation is successful, click the window OK button to exit. Connect the computer USB to the development board and power on, and then enter the computer device manager, you can see that the CH340 port is identified under the port, as shown in the following picture:
Shisa umgqomo file
- Open the “Flash_Download” folder in “8-快速使用_Quick_Start”, locate the “flash_download_tool” folder, open the folder, and double-click the exe executable file kwe-flash_download_tool. Njengoba kukhonjisiwe esithombeni esingezansi:
- After opening the Flash download tool, ChipType select “ESP32”,WorkMode select “Develop”,LoadMode keep the default (UART), and then click “OK” button, as shown below:
Faka isixhumi esibonakalayo sethuluzi lokulanda i-Flash, khetha kuqala umgqomo file ukusha, umgqomo file in the data package “8-快速使用_Quick_Start /bin” directory, as shown in the following figure:
- Chofoza inkinobho enamachashazi amathathu phakathi ukuze ukhethe umgqomo file ezinyathelweni ezingenhla. Ngemva kokukhetha, hlola ibhokisi elingaphambili bese usetha ikheli elivuthayo ngokuthi “0”, njengoba kukhonjisiwe esithombeni esilandelayo:
- Set SPI SPEED to “80MHz”, SPI MODE to “DIO”, and keep other Settings default, as shown in the following figure:
- Set COM, as long as the product is normally connected to the computer, COM port will be automatically recognized, click the drop-down menu to select. Set BAUD, click the drop-down menu to select, the larger the value, the faster the burning speed, but can not exceed the maximum transmission rate supported by the USB-to-serial chip. As shown in the picture below:
- Click the “START” button to enter the burning state. During the burning process, the status changes: “Waiting for synchronous power-on” -> “Downloading” -> “FINISH”, and the progress bar will also be loaded, as shown in the following picture:
Qalisa uhlelo
Ngemva kweBin file ishisiwe, cindezela inkinobho yokusetha kabusha yomkhiqizo noma amandla kumkhiqizo futhi, futhi ungabona umphumela wokusebenza wohlelo, njengoba kukhonjisiwe esithombeni esingezansi:
imibuzo ejwayelekile ukubuzwa
- Q: Ngiwenza kanjani amandla kumkhiqizo?
A: Use a Type-C cable with power supply and data transmission function to connect the computer to the product. - Q: Ngisifaka kanjani isishayeli se-USB-to-Serial Port?
A: Locate and decompress the USB-SERIAL_CH340.zip package, then run CH341SER.EXE for installation. - Umbuzo: Ngiwushisa kanjani umgqomo file?
A: Open the Flash_Download folder, run flash_download_tool, select ESP32 as ChipType, and follow the steps mentioned in the manual.
Amadokhumenti / Izinsiza
 |
I-lcdwiki E32R40T LCD Isibonisi Sesikrini Sokuthinta [pdf] Umhlahlandlela Womsebenzisi I-E32R40T, E32N40T, E32R40T LCD Isibonisi Sesikrini Sokuthinta, E32R40T, Isibonisi Sesikrini Se-LCD, Isibonisi Sesikrini Sokuthinta, Isibonisi Sesikrini, Isibonisi |